Parker F1 Series User manual

Effective: June, 2018
Supersedes: December, 2016
Bulletin HY30-5501-M1/UK
Service Manual
Series F1/T1

2Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series F1/T1
HY30-5501-M1/UK
List of contents Page
New attributes on F1/T1 ............................................................................3
...........................................................4
Check of shaft seal....................................................................................5
..............................................................6
Direction of rotation ...................................................................................8
...........................................................................................9
..............................................................................................10
Split view / spare parts ............................................................................ 11
Split view / spare parts (motor)................................................................12
Spare part kits and tools.......................................................................... 13
Conversion factors
1 cm3 3
Offer of Sale
Please contact your Parker representation for a detailed ”Offer of Sale”.
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED
HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
-
WARNING
!

3 Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series F1/T1
Bulletin HY30-5501-M1/UK
F1/T1
The F1/T1 series offers many additional
container lifts, skip loaders, forest cranes,
-
tions.
-
-
New features of the F1/T1 are:
-
ments
... thanks to:
All of this in addition to previous
features:
temperture shocks
ISO standard
F1-25/-41/-51/-61.
F1-81/-101.

4Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series F1/T1
HY30-5501-M1/UK
eliminates a separate drain line to the tank. F1 is
direct to PTO´s with ZF standard.
F1 is a piston pump with sherical pistons (1)
oto the shaft (3). When the shaft
rotates, the pistons move up and down in the cylin-
connects the cylinder barrel to the drive shaft, cau-
Design and function
F1 frame size 25 41 51 61 81 101
Displacement [cm3/rev] 25,6 40,9 51,1 59,5 81,6 102,9
1) [l/min]
2) 1852)
Max operating pressure [bar]
continuous 350 350
intermittent 400 400
Shaft speed [rpm]
1) 2600 2400 2200 2200 2000 2) 1800 2)
at 400 bar1) 2)
Torque [Nm]
Input power [kW]
Weight
on mineral oil at a viscosity of 30 mm2/s (cSt).
2) Valid with 21/2” inlet (suction) line.
Pump cross section
2
4
6
41
5

5 Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series F1/T1
Bulletin HY30-5501-M1/UK
Check of Shaft Seal and seal towards PTO
-
Indication hole is placed under the protection cover.
Note:
-

6Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series F1/T1
HY30-5501-M1/UK
-
ter and a relief valve.
Rpm
F01-025 1000 21,6
F01-041 1000 34,2
F01-051 1000 44,1
F01-061 1000 54,9
F01-081 1000
F01-101 1000 88,2
Test instrument with
valve

Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series F1/T1
Bulletin HY30-5501-M1/UK
Checking the performance of F1 motor
drain line and keep the drain port above a suitable container. Run the unit at normal speed
-
Pres-
sure
(bar)
(l/min)
F01-025-M 150 2.0
F01-041-M 150 2.5
F01-051-M 150 2.5
F01-061-M 150 2.5
F01-081-M 150 3.0
F01-101-M 150 3.0
F01-121-M 150 3.0

8Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series F1/T1
HY30-5501-M1/UK
3.
couple of turns. Take the mandrel which co-
-
sible to turn the mandrel 90°, down in the
-
Direction of rotation
The factory assembled direction of rotation,
appears on the label and by arrows on the
vs. shaft rotation. The direction of rotation
Remove the four cap screws and turn the
Nm.
-
Start-up
Make sure the entire hydraulic system is
5 Nm.
Disassembling
2.
protective washer (item 236).
Center screw
Plastic seal
1.
shaft upwards.

9 Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series F1/T1
Bulletin HY30-5501-M1/UK
6.
-
barrel support is kept in position in the bar-
rel with a snap function.
4.
Disassemble the end cap.
5.
Take out the shaft, the pistons, the barrel
support and the cylinder barrel from the
Only on the prototypes!

10 Pump and Motor Division
Trollhättan, Sweden
Service Manual
Series F1/T1
HY30-5501-M1/UK
Assembling
2.
Place the pistons and the barrel support in
the cylinder barrel. Place the shaft over the
pistons and on the barrel support. Turn the
-
ble the cylinder barrel on the end cap. En-
3.
4.
in two steps. First step with the assemble
tool alone. Second step with assemble tool
outher diameter of the casette seal with hy-
Fasten the assembly screw a couple of
possible. Reassemble the protective wash-
Fasten the end cap in a vice with the center
shaft upwards.
1.
Pressed in two steps.
Turn the shaft
at least on rev.
to ensure correct