Parkside Performance PKHAP 20-Li A1 User manual

CORDLESS HAMMER DRILL 20V PKHAP 20-Li A1
AKKU-KOMBIHAMMER 20 V
Originalbetriebsanleitung
IAN 364899_2101
CORDLESS HAMMER DRILL 20V
Translation of the original instructions
CIOCAN COMBI CU
ACUMULATOR 20 V
Traducerea instrucţiunilor de utilizare original
ΕΠΑΝΑΦΟΡΤΙΖΟΜΕΝΟ
ΚΡΟΥΣΤΙΚΟ ΔΡΑΠΑΝΟ 20 V
Μετάφραση των αυθεντικών οδηγιών λειτουργίας
AKU KOMBINIRANI ČEKIĆ 20 V
Prijevod originalnih uputa za uporabu
AKU KOMBINOVANI ČEKIĆ 20 V
Prevod originalnog uputstva za upotrebu

GB/CY Translation of the original instructions Page 1
HR Prijevod originalnih uputa za uporabu Stranica 15
RS Prevod originalnog uputstva za upotrebu Strana 29
RO Traducerea instrucţiunilor de utilizare original Pagina 43
GR/CY Μετάφραση των αυθεντικών οδηγιών λειτουργίας Σελίδα 57
DE/AT/CH Originalbetriebsanleitung Seite 71
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.
Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama
uređaja.
Pre čitanja rasklopite obe strane sa slikama te se upoznajte sa svim funkcijama uređaja.
Înainte de a citi instrucţiunile, priviţi imaginile şi familiarizaţi-vă cu toate funcţiile aparatului.
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις λειτουργίες
της συσκευής.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.

A
KOMPERNASS H. GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY

20V max.
18V
All Parkside tools and the chargers PLG 20 A1/A4/C1/A2/C2/
A3/C3/PDSLG 20 A1 of the X20V Team series are compatible with the
PAP 20 A1/A2/A3/B1/B3 battery pack.
Charging times
Charging currents
2 Ah
Battery pack
PAP 20 A1/B1
3 Ah
Battery pack
PAP 20 A2
4 Ah
Battery pack
PAP 20 A3/B3
max. 2.4 A
Charger PLG 20 A1/A4/C1
60 min
2,4 A
90 min
2,4 A
120 min
2,4 A
max. 3.5 A
Charger PLG 20 A2/C2
45 min
3,5 A
60 min
3,5 A
80 min
3,5 A
max. 4.5 A
Charger PLG 20 A3/C3
35 min
3,8 A
45 min
4,5 A
60 min
4,5 A
max. 4.5 A
Charger PDSLG 20 A1
35 min
3,8 A
45 min
4,5 A
60 min
4,5 A

PKHAP 20-Li A1 GB│CY │ 1■
Contents
Introduction............................................................2
Intended use........................................................................2
Depicted components.................................................................2
Package contents ....................................................................2
Technical specifications ...............................................................3
General power tool safety warnings .......................................4
1. Work area safety ..................................................................4
2.Electricalsafety...................................................................4
3. Personal safety....................................................................4
4. Power tool use and care ............................................................5
5. Use and handling of the cordless electrical power tool.....................................5
6.Service..........................................................................6
Appliance-specific safety instructions for hammer drills .......................................6
Original accessories/auxiliary equipment .................................................6
Safety guidelines for battery chargers ....................................................6
Before use ............................................................. 7
Charging the battery pack (seefig.A)....................................................7
Attaching/disconnecting the battery pack to/from the appliance...............................7
Checking the battery charge level .......................................................7
Use................................................................... 7
Additional handle....................................................................7
Depthstop.........................................................................7
Operation .............................................................8
Select operating mode................................................................8
Preselecting the rotation speed..........................................................8
Switching on and off .................................................................8
Changing the direction of rotation .......................................................8
Maintenance and cleaning................................................9
Disposal............................................................... 9
Kompernass Handels GmbH warranty ....................................10
Service...............................................................11
Importer .............................................................11
Translation of the original Conformity Declaration ...........................12
Ordering a replacement battery..........................................13
Telephone ordering .................................................................13

PKHAP 20-Li A1
■ 2 │ GB│CY
CORDLESS HAMMER DRILL 20V
PKHAP 20-Li A1
Introduction
Congratulations on the purchase of your
new appliance. You have chosen a high-
quality product. The operating instructions
are part of this product. They contain important
information about safety, usage and disposal.
Before using the product, please familiarise your-
self with all of the operating and safety instructions.
Use the product only as described and for the
range of applications specified. Please also pass
these operating instructions on to any future owner.
Intended use
The appliance is suitable for:
▯ Hammer-drilling into brickwork, concrete and
stone
▯ Chiselling into concrete, stone and plaster
▯ Drilling into stone, wood and metal
Any other usage or modification of the appliance
is deemed to be improper and carries a significant
risk of accidents.
The manufacturer accepts no responsibility for
damage(s) attributable to misuse. The appliance
is not intended for commercial use.
Depicted components
1Function selector switch
Release button for the function selector switch
2ON/OFF switch
3Rotation direction switch/lock
4Release button for the battery pack
5Battery pack*
6Battery charge level button
7Battery display LED
8Rotation speed preselector dial
9LED work light
0Additional handle
qTool holder with dust protector cap
wLocking collar
eScrew for the depth stop
rDepth stop
tHigh-speed charger*
zRed charge control LED
uGreen charge control LED
iGrease
Package contents
1 cordless hammer drill 20V
1 additional handle
1 metal depth stop
1 carrying case
50 g grease
1 set of operating instructions

PKHAP 20-Li A1 GB│CY │ 3■
Technical specifications
Cordless Hammer Drill 20V PKHAP 20-Li A1
Rated voltage 20 V (DC)
Idle speed n00–950 rpm
Stroke rate 0–4700 rpm
Impact energy 3 J
Max. drill diameter 13 mm for steel
27 mm for wood
24 mm for concrete
Battery PAP 20 A3*
Type LITHIUM ION
Rated voltage 20 V (DC)
Capacity 4 Ah (80Wh)
Cells 10
High-speed battery charger PLG 20 A3*
INPUT
Rated voltage 230–240 V ~, 50 Hz
(AC)
Rated power
consumption 120 W
Fuse (internal) 3.15 A T3.15A
OUTPUT
Rated voltage 21.5 V (DC)
Rated current 4.5 A
Charging time approx. 60 min
Protection class II/ (double insulation)
* BATTERY AND CHARGER ARE NOT INCLUDED
ATTENTION! Hot surface.
There is a risk of burns.
Noise emission value
Noise measurement value determined in accord-
ance with EN 60745. The A-rated noise level of
the power tool is typically as follows
Hammer-drilling
Sound pressure level LpA = 93.6 dB (A)
Uncertainty K = 3 dB
Sound power level LWA = 104 dB (A)
Uncertainty K = 3 dB
Total vibration value
Total vibration values (vector total of three direc-
tions) determined in accordance with EN 60745:
Hammer-drilling (main handle)
a
h, AG = 5.677 m/s2, K = 1.5 m/s2
(additional handle)
a
h, AG = 6.334 m/s2, K = 1.5 m/s2
WARNING!
► The vibration level specified in these instruc-
tions has been measured in accordance
with the standardised measuring procedure
specified in EN 60745 and can be used to
make equipment comparisons. The specified
vibration emission value can also be used to
make an initial exposure estimate.
The vibration level varies depending on the
use of the power tool and may, in some
cases, be higher than the value specified in
these instructions.

PKHAP 20-Li A1
■ 4 │ GB│CY
NOTE
► Try to keep the vibration loads as low as
possible. Measures to reduce the vibration
load are, e.g. wearing gloves and limiting the
working time. Wherein all states of operation
must be included (e.g. times when the power
tool is switched off and times where the power
tool is switched on but running without load).
General power tool
safety warnings
WARNING!
►Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery
operated (cordless) power tool.
1. Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmos-
pheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of elec-
tric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entan-
gled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
3. Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
b) Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.

PKHAP 20-Li A1 GB│CY │ 5■
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use
of dust collection can reduce dust-related
hazards.
4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many acci-
dents are caused by poorly maintained power
tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits,
etc., in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
5. Use and handling of the cordless
electrical power tool
a) Charge a rechargeable battery using only
the charger recommended by the manufac-
turer. There is a risk of fire if a battery charger
designed for a particular type of battery is used
with other batteries.
b) Only the rechargeable battery units supplied
are to be used with an electrical power tool.
The use of other rechargeable battery units may
lead to the danger of injury or fire.
c) When they are not being used, store recharge-
able battery units away from paperclips, coins,
keys, nails, screws or other small metal objects
that could cause the contacts to be bridged.
Short-circuiting the contacts of a rechargeable
battery unit may result in heat damage or fire.
d) Fluids may leak out of rechargeable battery
units if they are misused. If this happens,
avoid contact with the fluid. If contact occurs,
flush the affected area with water. Seek addi-
tional medical help if any of the fluid gets into
your eyes. Escaping battery fluid may cause
skin irritation or burns.
e) Do not use a damaged or modified battery.
Damaged or modified batteries may behave
unexpectedly and cause fires, explosions or
pose a risk of injury.
f) Do not expose a battery to fire or excessively
high temperatures. Fire or temperatures in excess
of 130°C (265°F) can cause an explosion.

PKHAP 20-Li A1
■ 6 │ GB│CY
g) Follow all instructions regarding charging
and never charge the battery or the cordless
tool outside of the temperature range given in
the operating instructions. Incorrect charging
or charging outside of the permissible tempera-
ture range can destroy the battery and increase
the risk of fire.
CAUTION! RISK OF EXPLOSION!
Never charge non-rechargeable
batteries.
Protect the
rechargeable battery from heat, e.g. from
continuous exposure to sunlight, fire, water
and moisture. There is a risk of explosion.
6. Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of
the power tool is maintained.
b) Never try to repair damaged batteries. Main-
tenance of batteries should only be carried out
by the manufacturer or an approved customer
service centre.
Appliance-specific safety instructions
for hammer drills
■Wear hearing protection. Exposure
to loud noise can lead to hearing loss.
■Use the additional handles supplied with the
appliance. Loss of control can lead to injuries.
■Hold the appliance by the insulated handles
when you are carrying out work during which
the deployed tool may come into contact with
concealed power cables or its own power
cable. Contact with a live wire may electrify
exposed metal parts of the tool and could give
the operator an electric shock.
■Wear a dust mask.
WARNING! TOXIC DUST!
► Working with the tool can produce harmful/
toxic dusts which represent a health hazard
for the person operating the appliance and
for anyone else in the vicinity.
■CAUTION, POWER CABLES! DANGER!
Ensure that you are not likely to contact power,
gas or water supply lines when you are working
with the power tool. If necessary, check with a
service line detector before you start to cut or
drill into a surface.
Original accessories/auxiliary
equipment
■Use only the accessories and additional
equipment that are specified in the operating
instructions and are compatible with the
appliance.
Safety guidelines for battery
chargers
■ This appliance may be used by
children aged 8 years and above
and by persons with limited phys-
ical, sensory or mental capabilities
or lack of experience and knowl-
edge, provided that they are under
supervision or have been told how
to use the appliance safely and are
aware of the potential risks. Do not
allow children to use the appliance
as a toy. Cleaning and user mainte-
nance tasks may not be carried out
by children unless they are super-
vised.
The charger is suitable for
indoor use only.

PKHAP 20-Li A1 GB│CY │ 7■
WARNING!
■ To avoid potential risks, damaged mains
cables should be replaced by the manufac-
turer, their customer service department or
asimilarly qualified person.
Before use
Charging the battery pack
(seefig.A)
CAUTION!
► Always unplug the appliance before you
remove the battery pack5from or connect
itto the charger.
■ Never charge the battery pack5when the
ambient temperature is below 10°C or above
40°C.
♦ Connect the battery pack5to the high-speed
battery chargert(see fig. A).
♦ Insert the power plug into the socket. The
control LEDzlights up red to indicate that the
appliance is charging.
♦ The green LEDuindicates that the charging
process is complete and the battery pack5is
ready.
♦ Push the battery pack5into the appliance.
Attaching/disconnecting the battery
pack to/from the appliance
Attaching the battery pack
♦ Push the rotation direction switch3into the
middle position (lock).
Allow the battery pack5to click into the
handle.
Removing the battery pack
♦ Press the release button4and remove the
battery pack5.
Checking the battery charge level
♦ Press the battery charge level button6to
check the charge level of the battery.
The status/remaining charge will be shown on
the battery display LED7as follows:
RED/ORANGE/GREEN = maximum charge/
performance
RED/ORANGE = medium charge/performance
RED = low charge – charge the battery
Use
Additional handle
NOTE
► For safety reasons, you should never use this
appliance without the additional handle0
attached.
♦ Remove the additional handle0by turning it
in a clockwise direction (see fold-out page).
♦ Turn the additional handle0to the desired
position.
♦ Fix the additional handle0in the new position
by turning it anticlockwise.
Depth stop
♦ Undo the screw on the depth stop e.
♦ Insert the depth stoprinto the additional
handle0.
♦ Ensure that the toothing on the depth stopr
is facing downwards.
♦ Pull the depth stoprout until the distance
between the tip of the drill and the tip of the
depth stop corresponds with the required
drilling depth.
♦ Tighten the screw on the depth stop eto
lock the depth stop rinto place.

PKHAP 20-Li A1
■ 8 │ GB│CY
Tool/chuck
♦ Grease the tool holderqslightly before
inserting the tool.
♦ Check that the tool is properly locked by pulling
it. The system has radial play because of the
design.
Removing a tool
♦ Pull the locking collarwbackwards and
remove the tool.
Operation
Select operating mode
WARNING!
► Do not press the function selector switch1
until the appliance has come to a complete
standstill. Switching between functions while
the tool is still rotating can damage the appli-
ance.
Function selector switch
♦ Press and hold the release button on the
function selector switch1. Turn the function
selector switch1so that the required symbol
engages at the arrow mark:
Function Symbol
Drilling
Hammer drilling
Chisel position adjustment
Chiselling
Adjusting the chisel position
You can rotate the tool to the required position for
chiselling using this function.
♦ Turn the function selector switch1to the
position.
♦ Turn the tool in the tool holderqto the
required position.
♦ Turn the function selector switch1to the
position for the chiselling function.
Preselecting the rotation speed
You can use the rotation speed preselector dial8
to preselect the rotation speed. Level 1 (low rota-
tion speed) up to level 6 (high rotation speed).
Work out the correct settings by carrying out a test:
– Level 3–6: high speed: for hammer drilling/
chiselling in concrete or stone
– Level 1–3: low speed: for drilling in steel or
wood
Switching on and off
Switching the appliance on
♦ Press the ON/OFF switch2.
Switching the appliance off
♦ Release the ON/OFF switch2.
Changing the direction of rotation
♦ Change the direction of rotation by pressing
the rotation direction switch3towards the left
or right.

PKHAP 20-Li A1 GB│CY │ 9■
Maintenance and cleaning
WARNING! RISK OF INJURY!
Always switch the appliance off and
remove the battery before carrying out
any work on the appliance.
The appliance is maintenance-free.
■ The appliance must always be kept clean, dry
and free from oil or grease.
■ Use a soft, dry cloth to clean the housing.
Never use petrol, solvents or cleansers which
can damage plastic.
■ Never allow liquids to get into the appliance.
■ Clean the tool holderqregularly.
♦ To do this, pull the locking collarwbackwards
and pull the dust protector cap off the tool
holderq.
♦ Before fitting a tool into the tool holdeq,
grease it lightly.
■ If a lithium-ion battery is to be stored for an
extended period, the charge level should be
checked regularly. The optimum charge level is
between 50% and 80%. The optimum storage
environment is cool and dry.
NOTE
► Replacement parts not listed (such as batteries,
switches) can be ordered via our Service
hotline.
WARNING!
■ If the connecting cable needs to be replaced,
this must be carried out by the manufacturer
or an authorised representative in order to
avoid safety hazards.
Disposal
The packaging is made from environ-
mentally friendly material and can be
disposed of at your local recycling
plant.
Do not dispose of power tools
in your normal domestic waste!
European Directive 2012/19/EU
requires that worn-out power tools be
collected separately and recycled in an environ-
mentally compatible manner.
Do not dispose of batteries in
your normal household waste!
Defective or worn-out rechargeable
batteries must be recycled according
to Directive 2006/66/EC. Take the battery pack
and/or appliance to a nearby collection facility.
Please consult your local authorities regarding
suitable disposal of worn out power tools/battery
packs.
Dispose of the packaging in an envi-
ronmentally friendly manner. Note
the labelling on the packaging and
separate the packaging material
components for disposal if necessary. The pack-
aging material is labelled with abbreviations (a)
and numbers (b) with the following meanings:
1–7: plastics, 20–22: paper and cardboard,
80–98: composites.
Your local community or municipal
authorities can provide information on
how to dispose of the worn-out product.

PKHAP 20-Li A1
■ 10 │ GB│CY
Kompernass Handels GmbH
warranty
Dear customer,
This appliance comes with a 5-year warranty
valid from the date of purchase. In the event that
this product has any defects, you, the buyer, have
certain statutory rights. Your statutory rights are
not limited in any way by the warranty described
below.
Warranty conditions
The warranty period starts on the date of purchase.
Please keep your receipt in a safe place. This will
be required as proof of purchase.
If any material or manufacturing fault occurs within
5 years of the product’s date of purchase, we will
either repair or replace the product for you or
refund the purchase price (at our discretion). This
warranty service requires that you present the
defective appliance and the proof of purchase
(receipt) within the 5-year warranty period,
together with a brief written description of the fault
and of when it occurred.
If the defect is covered by the warranty, your
product will either be repaired or replaced by us.
The repair or replacement of a product does not
signify the beginning of a new warranty period.
The X 20 V Team Series battery pack comes with
a 3-year warranty valid from the date of purchase.
Warranty period and statutory claims
for defects
The warranty period is not prolonged by repairs
effected under the warranty. This also applies to
replaced and repaired components. Any damage
and defects present at the time of purchase must be
reported immediately after unpacking. Repairs
carried out after expiry of the warranty period shall
be subject to a fee.
Scope of the warranty
This appliance has been manufactured in accord-
ance with strict quality guidelines and inspected
meticulously prior to delivery.
The warranty covers material faults or production
faults. The warranty does not extend to product
parts subject to normal wear and tear or to fragile
parts which could be considered as consumable
parts such as switches or parts made of glass.
The warranty does not apply if the product has
been damaged, improperly used or improperly
maintained. The directions in the operating instruc-
tions for the product regarding proper use of the
product are to be strictly followed. Uses and
actions that are discouraged in the operating
instructions or which are warned against must be
avoided.
This product is intended solely for private use and
not for commercial purposes. The warranty shall be
deemed void in cases of misuse or improper
handling, use of force and modifications/repairs
which have not been carried out by one of our
authorised Service centres.
The warranty period does not apply to
■ Normal reduction of the battery capacity
overtime
■ Commercial use of the product
■ Damage to or alteration of the product by the
customer
■ Non-compliance with safety and maintenance
instructions, operating errors
■ Damage caused by natural hazards

PKHAP 20-Li A1 GB│CY │ 11 ■
Warranty claim procedure
To ensure quick processing of your case, please
observe the following instructions:
■ Please have the till receipt and the item number
(IAN)364899_2101 available as proof of
purchase.
■ You will find the item number on the type plate
on the product, an engraving on the product,
on the front page of the operating instructions
(below left) or on the sticker on the rear or
bottom of the product.
■ If functional or other defects occur, please
contact the service department listed either by
telephone or by e-mail.
■ You can return a defective product to us free of
charge to the service address that will be
provided to you. Ensure that you enclose the
proof of purchase (till receipt) and information
about what the defect is and when it occurred.
You can download these instructions
along with many other manuals,
product videos and installation
software at www.lidl-service.com.
This QR code will take you directly to the Lidl
service page (www.lidl-service.com) where you
can open your operating instructions by entering
the item number (IAN) 364899_2101.
NOTE
► For Parkside tools, please send us only the
defective item without the accessories (e.g.
battery, storage case, assembly tools, etc.).
WARNING!
►Have the appliances repaired by the
Service Centre or a qualified electrician
and only using genuine replacement parts.
This will ensure that the safety of the appli-
ance is maintained.
►Always ensure that the power plug or the
mains cable is replaced only by the manu-
facturer of the appliance or by an approved
customer service provider.This will ensure that
the safety of the appliance is maintained.
Service
Service Great Britain
Tel.: [phone]
E-Mail: [email protected]
CY Service Cyprus
Tel.: [phone]
E-Mail: [email protected]
IAN 364899_2101
Importer
Please note that the following address is not the
service address. Please use the service address
provided in the operating instructions.
KOMPERNASS HANDELS GMBH
BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com

PKHAP 20-Li A1
■ 12 │ GB│CY
Translation of the original Conformity Declaration
We, KOMPERNASS HANDELS GMBH, documents officer: Mr. Semi Uguzlu, BURGSTR. 21,
44867 BOCHUM, Germany, hereby declare that this product complies with the following standards,
normative documents and EC directives:
Machinery Directive
(2006/42/EC)
EMC (Electromagnetic Compatibility)
(2014/30/EU)
RoHS Directive
(2011/65/EU)*
* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object of the decla-
ration described above complies with the requirements of the Directive 2011/65/EU of the European Parliament and
Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic appliances.
Applied harmonised standards
EN 60745-1:2009/A11:2010
EN 60745-2-6:2010
EN 60335-1:2012/A2:2019
EN 60335-2-29:2004/A11:2018
EN 62233:2008
EN 55014-1:2017/A11:2020
EN 55014-2:2015
EN 61000-3-2:2014
EN IEC 61000-3-2:2019
EN 61000-3-3:2013
EN 61000-3-3:2013/A1:2019
EN 50581:2012
Type designation of machine: Cordless Hammer Drill 20V PKHAP 20-Li A1
Year of manufacture: 04–2021
Serial number: IAN 364899_2101
Bochum, 11/06/2021
Semi Uguzlu
- Quality Manager -
We reserve the right to make technical changes in the context of further product development.

PKHAP 20-Li A1 GB│CY │ 13 ■
Ordering a replacement battery
If you want to order a replacement battery for your appliance, you can do so easily via the Internet on
www.kompernass.com or by telephone.
Due to limited stocks, this item may sell out in a relatively short time.
NOTE
► Online ordering of replacement parts is not possible in all countries. In this case, please contact the
Service hotline.
Telephone ordering
Service Great Britain Tel.: [phone]
CY Service Cyprus Tel.: [phone]
To ensure that your order is processed swiftly, have the article number of your appliance to hand
(e.g. IAN 364899_2101) in case of questions. The article number can be found on the type plate
or the title page of these instructions.

PKHAP 20-Li A1
■ 14 │ GB│CY

PKHAP 20-Li A1 HR │ 15 ■
Sadržaj
Uvod ................................................................16
Namjenska uporaba ................................................................16
Prikazane komponente...............................................................16
Opseg isporuke ....................................................................16
Tehnički podaci ....................................................................17
Opće sigurnosne napomene za uporabu električnog alata ....................18
1. Sigurnost na radnom mjestu.........................................................18
2. Električna sigurnost. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3. Sigurnost osoba ..................................................................18
4. Korištenje i rukovanje električnim alatom ...............................................19
5. Korištenje i rukovanje baterijskim alatom ...............................................19
6.Servis..........................................................................20
Sigurnosne napomene specifične zaudarne bušilice .......................................20
Originalni pribor/dodatni uređaji ......................................................20
Sigurnosne napomene za punjače......................................................20
Prije uključivanja uređaja ...............................................21
Punjenje paketa baterije (vidi sliku A)......................................................21
Umetanje/vađenje paketa baterija izuređaja.............................................21
Provjera stanja baterije...............................................................21
Uključivanjeuređaja ...................................................21
Dodatna ručka .....................................................................21
Dubinski graničnik ..................................................................21
Rukovanje............................................................22
Odabir načina rada.................................................................22
Odabiranje broja okretaja ............................................................22
Uključivanje i isključivanje ............................................................22
Promjena smjera okretanja............................................................22
Održavanje i čišćenje ...................................................23
Zbrinjavanje..........................................................23
Jamstvo tvrtke Kompernass Handels GmbH ................................24
Servis ...............................................................25
Uvoznik ..............................................................25
Originalna izjava o sukladnosti ..........................................26
Narudžba zamjenske baterije ...........................................27
Telefonska narudžba ................................................................27

PKHAP 20-Li A1
■ 16 │ HR
AKU KOMBINIRANI ČEKIĆ 20 V
PKHAP 20-Li A1
Uvod
Čestitamo na kupnji Vašeg novog uređaja.
Time ste se odlučili za vrlo kvalitetan
proizvod.
Upute za uporabu dio su opreme ovog proizvoda.
One sadrže važne napomene za sigurnost, rukova-
nje i zbrinjavanje. Prije uporabe proizvoda upoznajte
se sa svim napomenama za rukovanje i svim sigur-
nosnim napomenama. Proizvod koristite isključivo
na opisani način i u navedenim područjima uporabe.
U slučaju predaje proizvoda trećim
osobama predajte i svu dokumentaciju.
Namjenska uporaba
Uređaj je prikladan za:
▯ Udarno bušenje u cigli, betonu i kamenu
▯ Klesanje u betonu, kamenu i žbuci
▯ Bušenje u kamenu, drvetu i metalu
Svaki drugi način uporabe i svaka izmjena uređaja
smatra se nenamjenskom i krije znatnu opasnost od
nezgode.
Proizvođač ne preuzima odgovornost za štete
nastale nenamjenskom uporabom uređaja.
Uređaj nije namijenjen za komercijalnu uporabu.
Prikazane komponente
1Prekidač za odabir funkcije
Tipka za deblokadu prekidača za odabir funkcije
2Prekidač za uključivanje/isključivanje
3Prekidač za odabir smjera okretanja/blokada
4Tipka za deblokadu paketa baterija
5Paket baterija*
6Tipka za stanje baterije
7LED indikator baterije
8Kotačić za predodabir broja okretaja
9LED radna svjetiljka
0Dodatna ručka
qPrihvatnik za alat s poklopcem za zaštitu od
prašine
wČahura za blokadu
eVijak za dubinski graničnik
rDubinski graničnik
tBrzi punjač*
zCrveno LED svjetlo za kontrolu punjenja
uZeleno LED svjetlo za kontrolu punjenja
iMast
Opseg isporuke
1 Aku kombinirani čekić 20 V
1 Dodatna ručka
1 Metalni dubinski graničnik
1 Kofer za nošenje
50 g mast
1 Upute za uporabu