Parkside PKO 270 A1 User manual

 
COMPRESSOR
Operation and Safety Notes
Original operating instructions
3

KKOMPRESSOR
Brugs- og sikkerhedsanvisninger
Original betjeningsvejledning
PKO 270 A1
 
ΑΕΡΟΣΥΜΠΙΕΣΤΗΣ
Υποδείξεις χειρισμού και ασφαλείας
Πρωτότυπες Οδηγίες χρήσης
  
KOMPRESSOR
Bedienungs- und Sicherheitshinweise
Originalbetriebanleitung
Anleitung_4010362:_ 27.05.2010 13:05 Uhr Seite 1

COMPRESSOR
 
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of
the device.

Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.
 
Πριν ξεκινήσετε την ανάγνωση, ανοίξτε τη σελίδα με τις εικόνες και εξοικειωθείτε με όλες τις
λειτουργίες της συσκευής.
  
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit
allen Funktionen des Gerätes vertraut.
GB/CY Operation and Safety Notes Page 6
DK Brugs- og sikkerhedsanvisninger Side 18
GR/CY Υποδείξεις χειρισμού και ασφαλείας Σελίδα 30
DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 44
KOMPRESSOR
ΑΕΡΟΣΥΜΠΙΕΣΤΗΣ KOMPRESSOR
Anleitung_4010362:_ 27.05.2010 13:05 Uhr Seite 2

3
1
10 98
12
13
1
2
3
4
5
6
7
11
2 3
COMPRESSOR KOMPRESSOR
ΑΕΡΟΣΥΜΠΙΕΣΤΗΣ KOMPRESSOR
16
18
19
20
17
14
G H
15
4
Anleitung_4010362:_ 27.05.2010 13:06 Uhr Seite 3

4
4 5
6 7
24
23
8
26
25,26
8
22 23
15
9
A
10
10
11
11 22 23
23
24
24 15
25 26 826 23 24
24
B
11
10
Anleitung_4010362:_ 27.05.2010 13:07 Uhr Seite 4

5
10
12 13
D
CD F
EC
16
21
11
max
min
18
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 5

6
GB/
CY
The reprinting or reproduction by any other
means, in whole or in part, of documentation
and papers accompanying products is
permitted only with the express consent of the
ISC GmbH. Subject to technical changes
Table of contents: Page
1. Introduction .............................................................................8
2. Safety information ...................................................................8-10
3. Layout .....................................................................................10
4. Intended use ...........................................................................10
5. Technical data.........................................................................11
6. Before starting the equipment .................................................11
7. Assembly and starting.............................................................11-12
8. Replacing the power cable......................................................12
9. Cleaning, maintenance, ordering of spare parts and storage..12-13
10. Disposal and recycling ............................................................14
11. Possible causes of failure........................................................15
12. Declaration of conformity ........................................................16
13. Warranty certificate .................................................................17
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 6

7
GB/
CY
Warning! The equipment is remote-controlled and may start-up without warning.
Note the instructions for use!
Wear ear-muffs.
Beware of electrical voltage
Beware of hot parts

Additional safety instructions
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 7

1. Introduction
 Important.
When using the equipment, a few safety
precautions must be observed to avoid injuries
and damage. Please read the complete
operating manual with due care. Keep this
manual in a safe place so that the information is
available at all times. If you give the equipment
to any other person, give them these operating
instructions as well. We cannot accept any
liability for damage or accidents which arise
due to a failure to follow these instructions and
the safety information.
2. Safety information
 IMPORTANT
Read all the safety regulations and
instructions. Any errors made in following the
safety regulations and instructions may result in
an electric shock, fire and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
2.1 Safety information
 Important. The following basic safety
actions must be taken when using this
compressor in order to protect the user
from electric shocks and the risk of injury
and fire.
Read and follow these instructions before
using the equipment.
■Keep your work area tidy
Untidy work areas can result in accidents.
■Make allowance for ambient conditions
Do not expose the compressor to rain.
Never use the compressor in damp or wet
locations. There is a risk of electric shock!
Provide good lighting. Do not use the
compressor near flammable liquids or
gases. There is a risk of explosion!
■Guard against electric shock
Avoid bodily contact with earthed parts (e.g.
pipes, radiators, cookers and refrigerators).
■Keep children away
Do not allow other persons to touch the
compressor or cable, keep them away from
your work area.
■Keep your compressor in a safe place
When not in use, the compressor must be
stored in a dry, locked room out of children’s
reach.
■Do not overload your compressor.
It will work better and safer when used
within its quoted capacity range.
■Wear suitable work clothes
Never wear loose fitting clothes or jewelry.
They may get caught in moving parts.
Rubber gloves and non-slip shoes are
recommended when working outdoors.
Wear a hair net if you have long hair. Risk of
injury.
■Do not use the cable for purposes other
than that for which it is designed.
Do not carry the compressor by its cable
and do not use the cable to pull the plug out
of the socket. Protect the cable from heat,
oil and sharp edges. The cable/plug could
become damaged.
■Take care of your compressor.
Keep your compressor clean to ensure that
it works efficiently and safely. Follow the
maintenance instructions. Check the power
plug and cable on a regular basis and have
them replaced by an authorized specialist if
they are damaged. Check the extension
cable regularly and replace it if damaged.
■Pull the power plug
When the equipment is not in use and
before carrying out any maintenance work.
■Avoid unintentional starting
Make sure that the switch is turned off when
connecting the equipment to the power
supply.
■When using an extension cable
outdoors
Check that it is approved for outdoor duty
and is marked accordingly.
■Be alert at all times
Keep an eye on your work. Use common
sense when working. Never use the
compressor when you are distracted.
■Check the compressor for damage
Before using the compressor again, check
8
GB/
CY
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 8

the safety devices or any slightly damaged
parts to ensure that they are in good
working order. Check that the moving parts
are working correctly, that they do not jam,
and that no parts are damaged. Make sure
that all parts are fitted correctly to ensure
that the equipment remains safe to use.
Unless otherwise stated in the operating
instructions, damaged guards and parts
have to be repaired or replaced by a
customer service workshop. Damaged
switches have to be replaced by a customer
service workshop. Never use an electric
power tool with a switch that cannot be
turned on and off.
■Important.
For your own safety you must only use the
accessories and additional units listed in the
operating instructions or recommended or
specified by the manufacturer. The use of
mounted tools or accessories other than
those recommended in the operating
instructions or catalog may place your
personal safety at risk.
■Repairs may only be carried out by a
qualified electrician
Repair work must only be carried out by a
trained electrician, otherwise the equipment
may cause accidents.
■Noise
Use ear muffs when you use the
compressor.
■Replacing the power cable
To prevent injury, damaged power cables
may only be replaced by the manufacturer
or a qualified electrician. There is a risk of
electric shock!
■Filling tires
Directly after filling tires, check the pressure
with a suitable pressure gauge, for example
at your filling station.
■Roadworthy compressors for building
site operations
Make sure that all lines and fittings are
suitable for the maximum permissible
operating pressure of the compressor.
■Place of installation
Set up the compressor on an even surface.
2.2 Safety instructions for working with
compressed air and blow-out pistols
■The compressor pump and lines can
become very hot during operation.
Touching these parts will burn you.
■The air which is sucked in by the
compressor must be kept free of impurities
that could cause fires or explosions in the
compressor pump.
■When releasing the hose coupling, hold the
hose coupling piece with your hand. This
way, you can protect yourself against injury
from the rebounding hose.
■Wear safety goggles when working with the
blow-out pistol. Foreign bodies or blown off
parts can easily cause injuries.
■Do not blow at people with the blow-out
pistol or clean clothes while on the body.
Risk of injury.
2.3. Safety information for paint spraying
■Do not process any paints or solvents with a
flash point below 55° C. There is a risk of
explosion!
■Do not heat up paints or solvents. There is a
risk of explosion!
■If hazardous liquids are processed, wear
protective filter units (face guards). Also,
adhere to the safety information provided by
the manufacturers of such liquids.
■The details and designations of the
Ordinance on Hazardous Substances,
which are displayed on the outer packaging
of the processed material, must be
observed. Additional protective measures
are to be undertaken if necessary,
particularly the wearing of suitable clothing
and masks.
■Do not smoke during the spraying process
and/or in the work area. There is a risk of
explosion! Paint vapors are easily
combustible.
■Never set up or operate the equipment in
the vicinity of a fire place, open lights or
sparking machines.
■Do not store or eat food and drink in the
work area. Paint vapors are harmful to your
health.
■The work area must exceed 30 m3and
sufficient ventilation must be ensured during
9
GB/
CY
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 9

spraying and drying. Do not spray against
the wind. Always adhere to the regulations
of the local police authority when spraying
combustible or hazardous materials.
■Do not process media such as white spirit,
butyl alcohol and methylene chloride with
the PVC pressure hose. These media will
destroy the pressure hose.
2.4 Operating pressure vessels
■You must keep your pressure vessel in
good working order, operate the vessel
correctly, monitor the vessel, carry out
necessary maintenance and repair work
immediately and meet the relevant safety
precautions.
■The supervisory authority may enforce
essential control measures in individual
cases.
■A pressure vessel is not allowed to be used
if it has faults or deficiencies that can
endanger workers or third parties.
■Check the pressure vessel for signs of rust
and damage each time before using. Do not
use the compressor with a damaged or
rusty pressure vessel. If you discover any
damage, then please contact the customer
service workshop.
Do not lose this safety information.
3. Layout
1. Transport handle
2. Pressure switch
3. Pressure regulator
4. Quick-lock coupling (regulated compressed
air)
5. Pressure gauge (for reading the preset
vessel pressure)
6. Pressure gauge (for reading the vessel
pressure)
7. Pressure vessel
8. Supporting foot
9. Drain plug for condensation water
10. Hub cap
11. Wheel
12. Oil drain plug
13. Compressor pump
14. Compressed air hose
15. Air filter
16. Oil sealing plug
17. ON/OFF switch
18. Oil – level window
19. Safety valve
20. Quick-lock coupling (unregulated
compressed air)
21. Oil filler opening
22. Nut (self-locking)
23. Spring washer
24. Nut
25. Screw
26. Washer
4. Intended use
The compressor is designed to generate
compressed air for compressed-air driven tools
which can be driven with an air volume of up to
approx. 270 l/min (e.g. tire inflator, blow-out
pistol and paint spray gun). Due to the limited
air output it is not possible to use the
compressor to drive tools with very high air
consumption (for example orbital sanders, rod
grinders and hammer screwdrivers).
The equipment may only be used for the tasks it
is designed to handle. Any other use is deemed
to be a case of misuse. The user/operator and
not the manufacturer will be liable for any
damage or injuries of any kind caused as a
result of this.
Please note that our equipment has not been
designed for use in commercial, trade or
industrial applications. Our warranty will be
voided if the equipment is used in commercial,
trade or industrial businesses or for equivalent
purposes.
10
GB/
CY
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 10

5. Technical data
Mains connection: 230 V ~ 50 Hz
Motor rating kW: 1.8 kW
Mode of operation S1
Compressor speed min-1: 2850
Operating pressure bar: max. 8
Pressure vessel capacity (in liters): 24
Theoretical suction power l/min.: approx. 270
Sound power level LWA in dB: 94
KWA uncertainty 4 dB
Protection type: IP20
Weight of the unit in kg: 26,5
Oil (15W 40) 0.3 l
6. Before starting the equipment
■Check the equipment for damage which
may have occurred in transit. Report any
damage immediately to the transport
company used to deliver the compressor.
■Install the compressor in the vicinity of the
point of consumption.
■Avoid long air lines and supply lines
(extension cables).
■Make sure that the intake air is dry and
dust-free.
■Do not install the compressor in a damp or
wet room.
■The compressor may only be used in
suitable rooms (with good ventilation and an
ambient temperature from +5 °C to 40 °C).
There must be no dust, acids, vapors,
explosive gases or inflammable gases in the
room.
■The compressor is designed to be used in
dry rooms. It is prohibited to use the
compressor in areas where work is
conducted with sprayed water.
■The oil level in the compressor pump has to
be checked before putting the equipment
into operation (see 9.4).
7. Assembly and starting
 Important.
Remove the transportation braces
(between the compression pump and
cladding) prior to initial start-up. If the
transportation braces are not removed,
heat can build up and cause the
compressor to ignite.
 Important.
You must fully assemble the appliance
before using it for the first time.
You will require the following tools for assembly
and installation:
2 x open-ended wrench size 13 mm (not
included)
7.1 Fitting the wheels (11)
Fit the supplied wheels as shown in Figure 5.
7.2 Fitting the supporting foot (8)
Fit the supplied supporting foot as shown in
Figure 6.
7.3 Fitting the air filter (15)
Remove the transportation stop (B) and screw
the air filter (15) to the equipment. (Fig. 7, 8).
7.4 Changing the transportation cover (A)
Remove the transportation cover from the oil
filler opening (21) and insert the supplied oil
sealing plug (16) into the oil filler opening. (Fig.
9,10).
7.5 Mains connection
■The compressor is equipped with a mains
cable with shock-proof plug. This can be
connected to any 230V ~ 50 Hz shock-proof
socket which is protected by a 16 A fuse.
■Before you use the machine, make sure that
the mains voltage complies with the
specifications on the rating plate.
■Long supply cables, extensions, cable reels
etc. cause a drop in voltage and can
impede motor start-up.
■In the case of low temperatures below
+5°C, motor start-up is jeopardized as a
11
GB/
CY
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 11

result of stiffness.
7.6 ON/OFF switch (Fig. 2)
Pull the ON/OFF switch (17) upwards to switch
on the compressor. To switch off the
compressor, press the ON/OFF switch down.
7.7 Adjusting the pressure: (Fig. 1,3).
■You adjust the pressure on the pressure
gauge (5) using the pressure regulator (3).
■The set pressure can be taken from the
quick-lock coupling (4).
■The vessel pressure can be read on the
pressure gauge (6).
■The vessel pressure can be taken from the
quick-lock coupling (20).
7.8 Adjusting the pressure switch (Fig. 1)
The pressure switch (2) is set at the factory.
Cut-in pressure approx. 6 bar
Cut-out pressure approx. 8 bar
7.9 Fitting the compressed air hose
(Fig. 1, 3)
Use the compressed air hose (14) if you intend
to carry out work at a greater distance from the
compressor. To do so, connect the nipple (H)
on the compressed air hose to one of the quick-
release couplings (4, 20). Then attach the
compressed air tool to the quick-release
coupling (G) on the compressed air hose.
8. Replacing the power cable
If the power cable for this equipment is
damaged, it must be replaced by the
manufacturer or its after-sales service or
similarly trained personnel to avoid danger.
9. Cleaning, maintenance,
ordering of spare parts and
storage
 Important.
Pull the power plug before doing any
cleaning and maintenance work on the
appliance.
Risk of injury by electric shock.
 Important.
Wait until the equipment has cooled down
completely. Risk of burns!
 Important.
Always depressurize the equipment before
carrying out any cleaning and maintenance
work. Risk of injury.
9.1 Cleaning
■Keep the equipment free of dirt and dust as
far as possible. Wipe the equipment with a
clean cloth or blow it down with compressed
air at low pressure.
■We recommend that you clean the
equipment immediately after you use it.
■Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be
aggressive to the plastic parts in the
equipment. Ensure that no water can get
into the interior of the equipment.
■You must disconnect the hose and any
spraying tools from the compressor before
cleaning. Do not clean the compressor with
water, solvents or the like.
9.2 Maintenance work on the pressure
vessel (Figure 1)
Important. To ensure a long service life of the
pressure vessel (7), drain off the condensed
water by opening the drain plug (9) each time
after using. Release the vessel pressure.
Check the pressure vessel for signs of rust and
damage each time before using. Do not use the
compressor with a damaged or rusty pressure
vessel. If you discover any damage, then
please contact the customer service workshop.
12
GB/
CY
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 12

 Important.
The condensation water from the pressure
vessel will contain residual oil. Dispose of
the condensation water in an
environmentally compatible manner at the
appropriate collection point.
9.3 Safety valve (Figure 3)
The safety valve (19) has been set for the
highest permitted pressure of the pressure
vessel. It is prohibited to adjust the safety valve
or remove its seal. Actuate the safety valve
from time to time to ensure that it works when
required. Pull the ring with sufficient force until
you can hear the compressed air being
released. Then release the ring again.
9.4 Check the oil level at regular intervals
(Figure 11)
Place the compressor on a level and straight
surface. The oil level must be between the two
marks MAX and MIN on the oil level window
(Fig. 18). Changing the oil: Recommended oil:
SAE 15W 40 or an alternative of the same
quality. Oil should be refilled for the first time
after 100 hours of operation; thereafter the oil
should be drained and refilled after every 500
hours in service.
9.5 Changing the oil (Figure 1,10, 11)
Switch off the engine and pull the mains plug
out of the socket. After releasing any air
pressure you can unscrew the oil drain plug
(12) from the compressor pump (13). To
prevent the oil from running out in an
uncontrolled manner, hold a small metal chute
under the opening and collect the oil in a
vessel. If the oil does not drain out completely,
we recommend tilting the compressor slightly.
When the oil has drained out, refit the oil drain
plug (12).
Dispose of the old oil at a drop-off point for
old oil.
To fill in the correct quantity of oil, ensure that
the compressor stands on an even surface. Fill
new oil through the oil filler opening (21) until it
comes up to the maximum level. This is marked
with a red dot on the oil level window (18)
(Figure 11). Do not exceed the maximum filling
quantity. Overfilling the equipment may result in
damage. Refit the oil sealing plug (16) into the
oil filler opening (21).
9.6 Cleaning the intake filter
(Figure 3, 12, 13)
The intake filter prevents dust and dirt being
drawn in. It is essential to clean this filter after at
least every 300 hours in service. A clogged
intake filter will decrease the compressor’s
performance dramatically. Open the thumb
screw (E) to the remove the intake filter. Then
pull off the filter cover (C). Now you can remove
the air filter (F) and the filter housing (D).
Carefully tap out the air filter, filter cover and
filter housing. Then blow out these parts with
compressed air (approx. 3 bar) and reinstall in
reverse order.
9.7 Storage
 Important.
Pull the mains plug out of the socket and
ventilate the appliance and all connected
pneumatic tools. Switch off the compressor
and make sure that it is secured in such a
way that it cannot be started up again by
any unauthorized person.
 Important.
Store the compressor only in a dry location
which is not accessible to unauthorized
persons.
Always store upright, never tilted! Oil may
leak out!
9.8 Ordering replacement parts
Please provide the following information on all
orders for spare parts:
■Model/type of the equipment
■Article number of the equipment
■ID number of the equipment
For our latest prices and information please go
to www.isc-gmbh.info
13
GB/
CY
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 13

10. Disposal and recycling
The equipment is supplied in packaging to
prevent it from being damaged in transit. The
raw materials in this packaging can be reused
or recycled. The equipment and its accessories
are made of various types of material, such as
metal and plastic. Defective components must
be disposed of as special waste. Ask your
dealer or your local council.
For EU countries only
Never place any electric power
tools in your household refuse.
To comply with European Directive 2002/96/EC
concerning old electric and electronic
equipment and its implementation in national
laws, old electric power tools have to be
separated from other waste and disposed of in
an environment-friendly fashion, e.g. by taking
to a recycling depot.
Recycling alternative to the return request:
Instead of returning the equipment to the
manufacturer, the owner of the electrical
equipment is obliged to ensure that the
equipment is properly disposed of if he
abandons ownership. The old equipment can
be returned to a suitable collection point, that
will dispose of the equipment in accordance
with the national recycling and waste disposal
regulations. This does not apply to any
accessories or aids without electrical
components supplied with the old equipment.
14
GB/
CY
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 14

15
GB/
CY
11. Possible causes of failure
Problem Cause Solution
The compressor does not
start.
1. No supply voltage.
2. Insufficient supply voltage.
3. Outside temperature is too
low.
4. Motor is overheated.
1. Check the supply voltage,
the power plug and the
socket-outlet.
2. Make sure that the
extension cable is not too
long. Use an extension cable
with large enough wires.
3. Never operate with an
outside temperature of
below +5° C.
4. Allow the motor to cool
down. If necessary, remedy
the cause of the overheating.
The compressor starts but
there is no pressure.
1. The non-return valve leaks.
2. The seals are damaged.
3. The drain plug for
condensation water (9)
leaks.
1. Replace the non-return
valve.
2. Check the seals and have
any damaged seals replaced
by a service center.
3. Tighten the screw by hand.
Check the seal on the screw
and replace if necessary.
The compressor starts,
pressure is shown on the
pressure gauge, but the
tools do not start.
1. Loose hose connections.
2. Leak in a quick-lock
coupling.
3. Insufficient pressure set on
the pressure regulator (3).
1. Check the compressed air
hose and tools and replace if
necessary.
2. Check the quick-lock
coupling and replace if
necessary.
3. Increase the set pressure
with the pressure regulator.
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 15

16
GB/
CY
kerklärt folgende Konformität gemäß EU-Richtlinie und
Normen für Artikel
texplains the following conformity according to EU
directives and norms for the following product
pdéclare la conformité suivante selon la directive CE et les
normes concernant l’article
Cdichiara la seguente conformità secondo la direttiva UE e
le norme per l’articolo
Nverklaart de volgende overeenstemming conform EU
richtlijn en normen voor het product
mdeclara la siguiente conformidad a tenor de la directiva y
normas de la UE para el artículo
Odeclara a seguinte conformidade, de acordo com a
directiva CE e normas para o artigo
lattesterer følgende overensstemmelse i medfør af
EU-direktiv samt standarder for artikel
Uförklarar följande överensstämmelse enl. EU-direktiv och
standarder för artikeln
qvakuuttaa, että tuote täyttää EU-direktiivin ja standardien
vaatimukset
.tõendab toote vastavust EL direktiivile ja standarditele
jvydává následující prohlášení o shodě podle směrnice
EU a norem pro výrobek
Xpotrjuje sledečo skladnost s smernico EU in standardi za
izdelek
Wvydáva nasledujúce prehlásenie o zhode podľa smernice
EÚ a noriem pre výrobok
Aa cikkekhez az EU-irányvonal és Normák szerint a
következő konformitást jelenti ki
Pdeklaruje zgodność wymienionego poniżej artykułu z
następującymi normami na podstawie dyrektywy WE.
eдекларира съответното съответствие съгласно
Директива на ЕС и норми за артикул
Hpaskaidro šādu atbilstību ES direktīvai un standartiem
Gapibūdina šį atitikimą EU reikalavimams ir prekės
normoms
Qdeclară următoarea conformitate conform directivei UE
şi normelor pentru articolul
zδηλώνει την ακόλουθη συμμόρφωση σύμφωνα με την
Οδηγία ΕΚ και τα πρότυπα για το προϊόν
Bpotvrđuje sljedeću usklađenost prema smjernicama EU
i normama za artikl
fpotvrđuje sljedeću usklađenost prema smjernicama EU
i normama za artikl
4potvrđuje sledeću usklađenost prema smernicama EZ i
normama za artikal
Tследующим удостоверяется, что следующие
продукты соответствуют директивам и нормам ЕС
1проголошує про зазначену нижче відповідність
виробу директивам та стандартам ЄС на виріб
5ја изјавува следната сообрзност согласно
ЕУ-директивата и нормите за артикли
ZÜrünü ile ilgili AB direktifleri ve normları gereğince
aşağıda açıklanan uygunluğu belirtir
Lerklærer følgende samsvar i henhold til EU-direktivet
og standarder for artikkel
ELýsir uppfyllingu EU-reglna og annarra staðla vöru
Konformitätserklärung
Einhell Germany AG · Wiesenweg 22 · D-94405 Landau/Isar
Kompressor PKO 270 A1 (Parkside)
Standard references: EN 1012-1; EN 60204-1; EN 55014-1;
EN 55014-2; EN 61000-3-2; EN 61000-3-3
Landau/Isar, den 25.01.2010
First CE: 10 Archive-File/Record: 4010360-10-4142860-10
Art.-No.: 40.103.62 I.-No.: 11010 Documents registrar: Siegfried Roider
Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar
Weichselgartner/General-Manager Wang/Product-Management
x
x
x
2009/105/EC
2006/95/EC
2006/28/EC
2005/32/EC
2004/108/EC
2004/22/EC
1999/5/EC
97/23/EC
90/396/EC
89/686/EC_96/58/EC
x
x
x
2006/42/EC
2004/26/EC
Emission No.:
2000/14/EC_2005/88/EC
Annex IV
Notified Body:
Notified Body No.:
Reg. No.:
Annex V
Annex VI
Noise: measured LWA = 90 dB (A); guaranteed LWA = 94 dB (A)
P = 1,8 KW;
Notified Body: TÜV Rheinland
12. Declaration of conformity
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 16

17
GB/
CY
13. GUARANTEE CERTIFICATE
Dear Customer,
All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely
event that your device develops a fault, please contact our service department at the address shown on this
guarantee card. Of course, if you would prefer to call us then we are also happy to offer our assistance under
the service number printed below. Please note the following terms under which guarantee claims can be made:
1. These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights.
We do not charge you for this guarantee.
2. Our guarantee only covers problems caused by material or manufacturing defects, and it is restricted to the
rectification of these defects or replacement of the device. Please note that our devices have not been
designed for use in commercial, trade or industrial applications. Consequently, the guarantee is invalidated
if the equipment is used in commercial, trade or industrial applications or for other equivalent activities. The
following are also excluded from our guarantee: compensation for transport damage, damage caused by
failure to comply with the installation/assembly instructions or damage caused by unprofessional
installation, failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or
current type), misuse or inappropriate use (such as overloading of the device or use of non-approved tools
or accessories), failure to comply with the maintenance and safety regulations, ingress of foreign bodies
into the device (e.g. sand, stones or dust), effects of force or external influences (e.g. damage caused by
the device being dropped) and normal wear resulting from proper operation of the device. This applies in
particular to rechargeable batteries for which we nevertheless issue a guarantee period of 12 months.
The guarantee is rendered null and void if any attempt is made to tamper with the device.
3. The guarantee is valid for a period of 3 years starting from the purchase date of the device. Guarantee
claims should be submitted before the end of the guarantee period within two weeks of the defect being
noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee
period remains applicable to the device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts fitted will not result in an extension of the guarantee period, and no new
guarantee will become active for the work performed or parts fitted. This also applies when an on-site
service is used.
4. In order to assert your guarantee claim, please send your defective device postage-free to the address
shown below. Please enclose either the original or a copy of your sales receipt or another dated proof of
purchase. Please keep your sales receipt in a safe place, as it is your proof of purchase. It would help us if
you could describe the nature of the problem in as much detail as possible. If the defect is covered by our
guarantee then your device will either be repaired immediately and returned to you, or we will send you a
new device.
Of course, we are also happy offer a chargeable repair service for any defects which are not covered by the
scope of this guarantee or for units which are no longer covered. To take advantage of this service, please send
the device to our service address.
EINHELL Hellas A. E.
Lasithiou Str. 4
14342 Nea Philadelphia
Tel. [phone] · Fax [phone]
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 17

18
DK
Indholdsfortegnelse Side
1. Indledning ...............................................................................20
2. Sikkerhedsanvisninger ...........................................................20-22
3. Maskinbeskrivelse ..................................................................22
4. Formålsbestemt anvendelse...................................................22-23
5. Tekniske data..........................................................................23
6. Før ibrugtagning......................................................................23
7. Montage og ibrugtagning ........................................................23-24
8. Udskiftning af netledning ........................................................24
9. Renholdelse, vedligeholdelse,
reservedelsbestilling og opbevaring........................................24-25
10. Bortskaffelse og genbrug ........................................................26
11. Mulige årsager til driftsudfald .................................................27
12. Overensstemmelseserklæring ................................................28
13. Garantibevis ...........................................................................29
Genoptryk eller anden kopiering af
dokumentation og følgedokumenter til
produkter, også i uddrag, er kun tilladt med
udtrykkelig tilladelse fra ISC GmbH. Ret til tekniske ændringer forbeholdes
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 18

19
DK
Advarsel! Enheden er fjernstyret og kan gå i gang uden varsel
Læs og følg betjeningsvejledningen!
Brug høreværn!
Advarsel mod elektrisk spænding
Advarsel mod varme dele

Supplerende sikkerhedsanvisninger
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 19

1. Indledning
 Vigtigt!
Ved brug af denne type maskiner er der visse
sikkerhedsforanstaltninger, der skal tages
højde for for at undgå skader på personer og
materiel. Læs derfor betjeningsvejledningen
grundigt igennem. Opbevar
betjeningsvejledningen et praktisk sted, så du
altid har den lige ved hånden. Husk at lade
betjeningsvejledningen følge med maskinen,
hvis du overdrager den til andre! Vi fraskriver os
ethvert ansvar for skader på personer eller
materiel, der måtte opstå som følge af, at
anvisningerne i denne betjeningsvejledning,
navnlig vedrørende sikkerhed, ikke overholdes.
2. Sikkerhedsanvisninger
 ADVARSEL
Læs alle sikkerhedsanvisninger og øvrige
anvisninger. Hvis sikkerhedsanvisninger og
øvrige anvisninger ikke følges nøje som
beskrevet, kan elektrisk stød, brand og/eller
svære kvæstelser være følgen.
Alle sikkerhedsanvisninger og øvrige
anvisninger skal opbevares.
2.1 Sikkerhedsanvisninger
 Vigtigt! Ved brug af kompressoren skal
følgende grundlæggende
sikkerhedsforanstaltninger iagttages som
beskyttelse mod elektrisk stød og for at
imødegå fare for kvæstelser og brand.
Nedenstående anvisninger skal læses,
inden maskinen tages i brug.
■Hold orden på arbejdsstedet
Uorden på arbejdsstedet øger faren for
ulykker.
■Tag højde for indvirkninger fra
omgivelserne
Udsæt ikke kompressoren for regn. Brug
ikke kompressoren i fugtige eller våde
omgivelser. Fare for elektrisk stød! Sørg for
god belysning. Anvend ikke kompressoren i
nærheden af brændbare væsker eller
gasser. Eksplosionsfare!
■Beskyt dig mod elektrisk stød
Undgå kropsberøring med jordforbundne
dele, for eksempel rør, varmeapparat,
komfur, køleskab.
■Hold børn på god afstand!
Lad ikke andre personer berøre kompressor
eller ledning, hold andre borte fra
arbejdsområdet.
■Opbevar kompressoren sikkert
Den ubenyttede kompressor skal
opbevares i et tørt, aflåst rum, uden for
børns rækkevidde.
■Overbelast ikke kompressoren
Du arbejder bedre og mere sikkert inden for
det angivne effektområde.
■Bær egnet arbejdstøj
Bær ikke smykker eller fyldigt,
løsthængende tøj. Dette vil kunne blive
trukket ind af bevægelige dele. Ved arbejde
i det fri anbefales det at bruge
gummihandsker og skridsikkert fodtøj. Brug
hårnet, hvis du har langt hår. Fare for
kvæstelse!
■Brug ikke kablet til utilsigtede formål
Træk ikke kompressoren i kablet, og hiv
ikke i kablet, når du trækker stikket ud af
stikdåsen. Beskyt ledningen mod varme,
olie og skarpe kanter. Ledning/Stik kan blive
beskadiget.
■Plej kompressoren omhyggeligt
Hold kompressoren ren, så du kan arbejde
sikkert og effektivt. Følg
vedligeholdelsesforskrifterne. Kontroller stik
og ledning med jævne mellemrum; i tilfælde
af beskadigelse skal udbedring ske ved
autoriseret el-fagmand. Kontroller med
jævne mellemrum forlængerledninger; en
beskadiget forlængerledning skal
omgående skiftes ud.
■Træk netstikket ud
Når maskinen ikke er i brug, før
vedligeholdelse.
■Undgå utilsigtet igangsætning
Forvis dig om, at der er slukket på
afbryderen, når tilslutningen til
strømforsyningsnettet oprettes.
■Udendørs forlængerledninger
Forlængerledninger til udendørs brug skal
være særligt godkendt til formålet - se
20
DK
Anleitung_4010362:_ 27.05.2010 13:08 Uhr Seite 20