Parkside PISG 80 A3 User manual

INVERTER WELDER
Operation and Safety Notes
Translation of the original instructions
IAN 310850
INVERTER-SCHWEISSGERÄT
Bedienungs- und Sicherheitshinweise
Originalbetriebsanleitung
DE
GB ATIE CHNI
INVERTER WELDER PISG 80 A3
NIIE

GB IE NI
Before reading, unfold the page containing the illustrations and familiarise yourself with all
functions of the device.
DE AT CH
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich
anschließend mit allen Funktionen des Gerätes vertraut.
GB/IE/NI Operation and Safety Notes Page 5
DE/AT/CH Montage-, Bedienungs- und Sicherheitshinweise Seite 21

–
(schwarz)
+
(rot)
1
2
4
10
9
3
5
6 7 11
8

D
C3 C4
C1 C2
A B
8 7
7
11
5

5GB/IE/NI
Table of contents
List of pictograms used .........................................................................Page 6
Introduction..............................................................................................Page 7
Intended use................................................................................................Page 7
Parts Description ..........................................................................................Page 7
Technical specifications.................................................................................Page 7
Scope of delivery.........................................................................................Page 7
Safety instructions..................................................................................Page 8
Safety hazardsduring arc welding..................................................................Page 9
Safety notices specific to the welding shield ....................................................Page 12
Tight and moist spaces..................................................................................Page 12
Protective clothing .......................................................................................Page 13
Protecting againstrays and burns ...................................................................Page 13
Prior to commissioning .........................................................................Page 13
Installing the welding shield ...............................................................Page 13
Start up .....................................................................................................Page 14
Welding.....................................................................................................Page 15
Maintenance and Cleaning ..................................................................Page 15
Information about warranty and service processing...................Page 16
Warranty terms............................................................................................Page 16
Extent of warranty........................................................................................Page 16
Processing of warranty claims........................................................................Page 17
Environmental instructions and disposal information..................Page 17
EU Conformity Declaration...................................................................Page 17

6GB/IE/NI
List of pictograms used
Caution!
Read instructions for use! WARNING Potential of serious to fatal injuries.
1~50Hz
Power input;
phase number, as well as
Alternating current symbol
and rated value of the fre-
quency
Caution! Risk of electric
shock!
Important notice!
Do not dispose of electrical
equipment in household
waste!
Dispose of packaging and
device in an environmentally-
friendly way!
Do not use the device out-
doors and never in rain! Manual arc welding with covered electrodes
Electric shock from the weld-
ing electrode can be fatal IP21S Protection type
Inhaling welding smoke can
be hazardous to your health. Suitable for welding with increased electric risk
Welding sparks can cause an
explosion or fire.
Single phase static frequency
converter-transformer
rectifier
Arc rays can damage the
eyes and injure the skin. HInsulation class
Electromagnetic fields can
interfere with the functionality
of pacemakers. Direct current
Attention, potential dangers! Made from recycling
material.
List of pictograms used

7GB/IE/NI
INVERTER WELDER
PISG 80 A3
zIntroduction
Congratulations! You have
chosen a high-quality unit
from our company. Familiar-
ise yourself with the product before using it
for the first time. In addition, please carefully
refer to the instructions for use and the safety
instructions below. Initial operation of this
tool must be performed by trained person-
nel.
KEEP OUT OF THE REACH OF
CHILDREN!
zIntended use
This welding tool is suitable for welding
metals such as carbon steel, alloy steel, other
stainless steels, copper, aluminium, titanium,
etc. The product has a control lamp, a ther-
mal protection indicator, and a cooling fan.
It further has a strap to safely lift and move
the product. Improper product handling
can be dangerous to persons, animals and
objects. Only use the product as described
and for its indicated purpose. Keep these
instructions in a safe place. When passing
this product on to others, please also include
all the documents. Any use other than the in-
tended is prohibited and potentially danger-
ous. Damages resulting from non compliance
or misuse are not covered by the warranty
and are not included in the manufacturer‘s
liability.
Note: Classification per EMV standard:
Class A per IEC 60974-10
Warning: Equipment categorised Class A
are intended for industrial use. When used
in other areas, electromagnetic tolerance
may not be warranted or failures may occur.
zParts Description
1
Carrying strap
2
Overheating control lamp
3
Control knob
4
Earth terminal
5
Electrode holder
6
Combination wire brush with chipping
hammer
7
Welding shield
8
Grip
9
ON / OFF switch
10
Mains lead
11
Protection glass
zTechnical specifications
Mains connection: 230V~ 50Hz
Max. welding current
and the respective
conventional load voltage: 10 A/20,4 V -
80 A/23,2 V
Rated value of the
Mains voltage: U1: 230 V
Highest rated value
of the mains current: I1max: 14,3 A
Maximum effective
input current: I1eff: 7,8 A
Rated value of the
no-load voltage: U0: 68 V
Protection class: IP21S
Weight: 3,2 kg
Duty cycle X: 30 %
Falling characteristic
zScope of delivery
1 Inverter welder
1 Welding shield
2 Welding cables
1 Combination wire brush with chipping
hammer
1 Carrying strap
5 Welding electrodes (2 x 1.6 mm;
2 x 2.0 mm; 1 x 2.5 mm)
1 Instructions for use
Introduction

8GB/IE/NI
zSafety instructions
Please carefully read the instruc-
tions for use and follow the spec-
ified notices. Familiarise yourself
with the tool, its proper use and
the safety notices using these in-
structions for use. The nameplate
contains all the technical data for
this welding tool, please learn
about the technical facts of this
tool.
This device may be used by
children aged 16 years and
up, as well as by persons with
reduced physical, sensory or
mental capacities, or lacking
experience and / or knowl-
edge, so long as they are
supervised or instructed in the
safe use of the device and un-
derstand the associated risks.
Do not allow children to play
with the appliance. Cleaning
and user maintenance should
not be performed by children
without supervision.
Only have repairs and / or
maintenance performed by
electrically skilled persons.
Only use the welding ca-
bles included (PISG 80 A3,
H01N2-D1x10 mm2).
During use the equipment
should not be located directly
against a wall, be covered,
or be jammed between other
equipment to ensure ample air
can be taken in through the
ventilation louvres. Verify the
equipment is correctly connect-
ed to the mains voltage. Avoid
any tensile load on the mains.
Unplug the mains plug from
the socket before transferring
the equipment to a different
location.
Always switch the equip-
ment off with the ON / OFF
switch when not in use. Set
the electrode holder down on
an insulated pad and allow
to cool for 15 minutes before
removing the electrodes from
the holder.
Pay attention to the condition
of the welding cables, the elec-
trode holders and the earth
terminals. Worn insulation and
conducting parts can produce
hazards and reduce the weld-
ing quality.
Arc welding produces sparks,
melted metal parts and smoke.
Therefore note: Remove any
flammable substances and
/ or materials from the work
area and its immediate sur-
roundings.
Ensure the work area is venti-
lated.
Safety instructions

9GB/IE/NI
Do not weld atop containers,
receptacles or pipes, which
do or did contain flammable
liquids or gasses.
WARNING Avoid any direct
contact with the welding
circuit. The no-load voltage
between the electrode holder
and earth terminal can be dan-
gerous, there is a risk of elec-
tric shock.
Do not store or use the equip-
ment in a moist or wet environ-
ment or in the rain. The Protec-
tion Provision IP21S applies in
this respect.
Protect the eyes with the ap-
propriate safety glass (DIN
Grad 9-10) to be installed in
the included welding shield.
Use gloves and dry protec-
tive clothing free from oil and
grease to protect the skin from
ultraviolet rays and the arc.
WARNING Do not use the
welding power source to thaw
pipes.
Remember:
The arc ray can damage the
eyes and cause burns to the
skin.
Arc welding produces sparks
and drops of molten metal, the
welded work piece begins to
glow and remains very hot for
a relatively long time. There-
fore do not touch the work
piece with bare hands.
Arc welding releases noxious
fumes. Be careful not to inhale
these as best possible.
Protect yourself from the danger-
ous effects of the arc and keep
persons not involved in the work
at least 2 m away from the arc.
ATTENTION!
Depending on mains condi-
tions at the connection point,
operating the welding equip-
ment may interfere with the
voltage supply for other loads.
When in doubt, please contact
your power supply company.
Operating the welding equip-
ment may interfere with the
functionality of other devices,
e.g. hearing aids, pacemak-
ers, etc.
zSafety hazards
during arc welding
Arc welding produces a variety
of safety hazards. It is therefore
particularly important for the
welder to observe the following
rules to avoid putting himself and
others in danger and to prevent
damage to persons and the
equipment.
Safety instructions

10 GB/IE/NI
Only have work to the mains
voltage end, e.g. to cables,
plugs, outlets, etc. performed
by a electrically skilled person
in accordance with national
and local regulations.
In the event of an accident,
immediately disconnect the
welding equipment from the
mains voltage.
If electrical contact voltage
occurs, immediately switch
the equipment off and have
it inspected by an electrically
skilled person.
Always ensure good electrical
contacts on the welding cur-
rent end.
Always wear insulating gloves
on both hands whilst welding.
These will protect from electric
shock (no-load voltage of the
welding current), from hazard-
ous rays (heat and UV rays)
and glowing metal and weld
splashes.
Wear solid, insulating shoes.
The shoes should also insulate
when exposed to moisture.
Low shoes are not suitable, as
glowing metal drops falling
could cause burns.
Wear suitable protective cloth-
ing, no synthetic garments.
Do not look into the arc with
unprotected eyes, only use a
welding shield with approved
protective glass per DIN. In
addition to light- and heat rays
which could result in blinding
or burns, the arc also emits UV
rays. Without adequate pro-
tection, this invisible ultraviolet
radiation causes very painful
conjunctivitis which is only
noticed a few hours later. UV
rays further cause burns simi-
lar to a sunburn in unprotected
areas of the body.
Persons near the arc or assis-
tants must also be informed of
the risks and outfitted with the
necessary protection. If neces-
sary, set up protective panels.
Ensure an adequate supply of
fresh air whilst welding, par-
ticularly in small spaces, as it
produces smoke and harmful
gasses.
Do not weld containers in
which gasses, fuels, mineral
oils, etc. were stored - even if
emptied a long time ago - as
residue poses an explosion
hazard.
Special regulations apply in
rooms posing fire- and explo-
sion hazards.
Welded joints exposed to
great strain and needing to
meet certain safety require-
Safety instructions