Partner EM-220 User manual

EM-220
User Manual

i
Copyright
This publication, including all photographs, illustrations and software, is protected under international
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no
representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark recognition
All product names used in this manual are the properties of their respective owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to
ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not
expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.
WARNING
This is a class A product. In a domestic environment this product may
causeradio interference in which case the user may be required to take
adequate measures.
Declaration of conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

ii
About this manual
This manual is intended for system administrators who are familiar with setting up a new system and
installing an operating system.
The manual consists of the following sections:
Chapter 1 Getting Started: This section covers unpacking and checking the
package contents, identifying components, installing the
battery pack, charging the battery and powering on.
Chapter 2 BIOS Setup Utility: The BIOS chapter provides information on navigating
and changing settings in the BIOS Setup Utility.
Chapter 3 Upgrading Components: This section provides information on upgrading
components.
Appendix: The appendix covers troubleshooting, information
on having the EM-220 serviced, and technical
specications.
Safety information
Before installing and using the EM-220, take note of the following precautions:
• Read all instructions carefully.
• SAR compliance for body-worn operations is restricted which provide at least 2 cm separation between
the device and the user’s body
• Do not place the unit on an unstable surface, cart, or stand.
• Do not block the slots and opening on the unit, which are provided for ventilation.
• Do not push objects in the ventilation slots as they may touch high voltage components and result in
shock and damage to the components.
• Do not place anything on the power cord. Place the power cord where it will not be in the way of foot
traffic.
• Follow all warnings and cautions in this manual and on the unit case.
• When replacing parts, ensure that your service technician uses parts specified by the manufacturer.
• Avoid using the system near water, in direct sunlight, or near a heating device.
• Never throw the battery into a fire or put it near a fire.
WARNING
Warning! Batteries may explode if not handled properly. Do not disas-
semble or dispose of them in re. Keep them away from children. Follow
local regulations when disposing of used batteries.
警告
不正確地更換電池會有爆炸的危險。僅可更換為廠商建議的相同電池或相同型
式電池。請依據廠商說明書棄置電池。
注意
用错误型号电池更换会有爆炸危险务必按照说明处置用完的电池。

iii
TABLE OF CONTENTS
CHAPTER 1 GETTING STARTED................................................ 1
Unpacking the machine..................................................................................1
Checking the package contents ....................................................................2
Identifying components .................................................................................3
Installing the battery pack ..............................................................................8
Charging the battery pack..............................................................................9
Powering on .................................................................................................10
CHAPTER 2 BIOS SETUP...........................................................11
About the Setup Utility .................................................................................11
Entering the Setup Utility ........................................................................12
BIOS navigation keys ..............................................................................12
Using BIOS .............................................................................................13
Main Screen.................................................................................................14
Advanced Settings .......................................................................................15
IDE Conguration ....................................................................................16
General ACPI Conguration ....................................................................17
USB Conguration ...................................................................................18
Boot Settings................................................................................................19
Boot Settings Conguration .....................................................................20
Boot Device Priority .................................................................................21
Hard Disk Drives......................................................................................22
Network Drives ........................................................................................23
Security Settings ..........................................................................................24
Chipset Settings...........................................................................................25
North Bridge Chipset Conguration .........................................................26
Exit Menu .....................................................................................................27
CHAPTER 3 UPGRADING COMPONENTS............................... 29
Safety and precautions ................................................................................29
Before you begin..........................................................................................30
Upgrading the hard drive..............................................................................31
Upgrading the memory module....................................................................33
Upgrading the Mini-PCIE card .....................................................................34
APPENDIX .................................................................................. 37
Troubleshooting ...........................................................................................37

iv
Tips for Troubleshooting...............................................................................37
General Problems .......................................................................................38
Having the EM-220 Serviced ......................................................................39
Specication.................................................................................................40
Revision history
Version 1.0, August 2011

1
CHAPTER 1
GETTING STARTED
This chapter describes the procedures from unpacking the EM-220, to powering it on. The following topics
are described.
• Unpacking the machine on page 1
• Checking the package contents on page 2
• Identifying components on page 3
• Installing the battery pack on page 8
• Charging the battery pack on page 9
• “Powering on” on page 10
Unpacking the machine
The machine and cable accessories are packed in a cardboard carton with foam padding for protection during
shipping.
Figure 1.1 Unpacking the
machine
Carefully unpack the machine and keep the packing materials. If you need to ship it in the future, repack it as
shown in Figure 1.1.

2 CHAPTER 1 GETTING STARTED
Checking the package contents
After you unpack the device, check that the following items are included.
If any item is missing or appears damaged, contact your dealer immediately.
AC adapter
Driver CD with drivers
and the user manual
PDF le.
EM-220
Metal Stylus
Battery
Power cord
Protection pack
Quick Start Guide
QSG

3
Identifying components
This section describes the parts and connectors on the machine.
Front view
1 2 3 4 5 6 7
98
Figure 1.2 Front view
Component Description
1 Power indicator
2 Battery charging indicator
3 HDD status indicator
4 WiFi On/ Off indicator
5 Bluetooth On/ Off indicator
6 3.5G LAN On/Off indicator (optional)
7 Built-in Microphone
8 Camera (optional)
9 10.1-inch touch panel

4 CHAPTER 1 GETTING STARTED
Left view
1
Figure 1.3 Left view
Component Description
1 5-in-1 media card slot
2 Express card slot
3 USB port
4 Power button
5 RJ45 LAN jack
6 DC IN
32 4 5 6

5
Right view
Figure 1.4 Right view
1 32 4 5
Component Description
1 VGA port
2 Ventilation hole
3 USB port
4 Headphone jack
5 Microphone jack

6 CHAPTER 1 GETTING STARTED
Rear view
Figure 1.5 Rear view
13 32 1
Component Description
1 Speaker
2 Battery pack
3 Charger pin: connect to a cradle for charging the battery.
Do not short-circuit these 2 charger pins. A short-circuit may cause
damage to the machine and present risks for electric shock or re.
IMPORTANT

7
Bottom view
Figure 1.6 Bottom view
12 1
3 4 5 6 7
Component Description
1 Mounting hole
2 Camera (optional)
3 Battery lock switch
4 Memory, WiFi module and 3.5G LAN module (optional) slots
5 Battery pack
6 HDD compartment
7 Battery release latch

8 CHAPTER 1 GETTING STARTED
Installing the battery pack
1. Overturn the EM-220
so that the bottom is
facing up toward you, as
shown in the right. Slide
the battery release latch
to the unlock position.
2. Align EM-220 battery
compartment pins to
the battery connector.
Slightly slide and press
the battery pack into the
compartment until the
battery lock switch is
bounced back.
3. As shown in the right,
slide the battery release
latch to the lock posi-
tion.

9
Charging the battery pack
Plug the AC adapter power cord into an electrical outlet, then connect the DC plug of the adapter cable to the
EM-220.Ittakesapproximately2–4hourstofullychargethebatteryforthersttime.Subsequentcharges
might take longer.
IMPORTANT
To protect and prolong the life of the battery, do not charge it for 24
hours or longer at a time.
NOTE
Charge the battery within a temperature range 0˚C to 45˚C.
Please make sure to perform 3 complete full charge and discharge
cycles to get optimal battery capacity. Failure to comply will result in
shorter battery lifespan.
IMPORTANT
If battery is not used, please store in dry area within a temperature
range of -10˚C ~ 20˚C. It is necessary to charge the battery once every
3 months to avoid battery degradation. Battery may become unusable
if the above is not respected.
IMPORTANT

10 CHAPTER 1 GETTING STARTED
Powering on
The power button located on the left side of the EM-220, press the power button the turn it on.
To force power off , long press the power button for 4~5 seconds.
NOTE

11
CHAPTER 2
BIOS SETUP
The primary function of the BIOS (Basic Input and Output System) is to identify and initiate component
hardware. The BIOS parameters are stored in non-volatile BIOS memory (CMOS). CMOS contents don’t get
erased when the computer is turned off. The following topics are described in this chapter.
• About the Setup Utility on page 11
• Main Screen on page 14
• Advanced Settings on page 15
• Boot Settings on page 19
• Security Settings on page 24
• Chipset Settings on page 25
• Exit Menu on page 27
About the Setup Utility
TheBIOSSetupUtilityenablesyoutocongurethefollowingitems:
• Hard drives, diskette drives, and peripherals
• Video display type and display options
• Password protection from unauthorized use
• Power management features
This Setup Utility should be used for the following:
• Whenchangingthesystemconguration
• WhenacongurationerrorisdetectedandyouarepromptedtomakechangestotheSetupUtility
• WhentryingtoresolveIRQconicts
• WhenmakingchangestothePowerManagementconguration
• When changing the User or Supervisor password

12 CHAPTER 2 BIOS SETUP
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of
built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message
appears:
Press DEL to run Setup
Press the delete key <Delete> to access the BIOS Setup Utility:
BIOS navigation keys
The BIOS navigation keys are listed below.
Key Function
←→ Select screens
↑↓ Select items
+ – Modiestheselectedeld’svalues
Enter Go to sub screen
F1 Displays the general help
F10 SavesthecurrentcongurationandexitsSetup
Esc Exits the current screen
Figure 2.1 Main BIOS screen

13
Using BIOS
When you start the Setup Utility, the main screen appears. The main screen of the Setup Utility displays a list
of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow
keys to move the highlight to other options. When an option is highlighted, execute the option by pressing
<Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option.
Other options lead to dialog boxes that prompt you for information.
Someoptions(markedwithatriangle►)leadtosubscreensthatenableyoutochangethevaluesforthe
option. Use the cursor arrow keys to scroll through the items in the sub screen.

14 CHAPTER 2 BIOS SETUP
Main Screen
This screen includes System BIOS Information, Processor, System memory and displays the System Time
and System Date.
System Overview
This screen displays System BIOS Information, Processor, System memory, System Time and System Date.
System Time/ System Date
The System Time and System Date items show the current date and time held by the machine. If you are
running a Windows OS, these items are automatically updated whenever you make changes to the Windows
Time and Date Properties utility.
Figure 2.2 Main Screen