Patton electronics CopperLINK 2172 User manual

USER
MANUAL
MODEL 2172
CopperLINK™ High Speed
Ethernet Extenders
SALES OFFICE
[phone]
TECHNICAL SUPPORT
[phone]
Part# 07M2172-UM
Doc# 03333U2-001
Rev. B
Revised 12/4/08
An ISO-9001Certified
Company
This is a Class A device and is intended for use in a
light industrial environment. It is not intended nor
approved for use in an industrial or residential
environment.

2
CONTENTS
1.0 Warranty Information ................................................................. 4
1.1 Compliance................................................................................... 4
EMC Compliance:......................................................................... 4
Safety Compliance: ...................................................................... 4
1.2 Radio and TV Interference (FCC Part 15) .................................... 4
1.3 CE Declaration of Conformity ....................................................... 5
1.4 Authorized European Representative........................................... 5
1.5 Service.......................................................................................... 5
1.6 Safety When Working With Electricity .......................................... 6
2.0 General Information.................................................................... 7
2.1 Features........................................................................................ 7
2.2 Description.................................................................................... 7
3.0 Installation................................................................................... 8
3.1 Connecting the Twisted-Pair Line Interface.................................. 9
3.2 Connecting the 10/100Base-T Ethernet Interface ...................... 11
3.3 Connecting Power ...................................................................... 12
4.0 Configuration ............................................................................ 12
4.1 Configuring the hardware DIP switches...................................... 12
4.2 Configuring DIP Switch S2 ......................................................... 14
Switch S2-1: Symmetric/Asymmetric Operation......................... 14
Switches S2-2 and S2-3: Data Rate........................................... 14
5.0 Operation................................................................................... 16
5.1 Power Up .................................................................................... 16
5.2 Front Panel LED Status Monitors ............................................... 17
ASpecifications ........................................................................... 18
A.1 LAN Connection .......................................................................... 18
A.2 Transmission Line ....................................................................... 18
A.3 CopperLINK Line Rate and CopperLINK Distance .................... 18
A.4 CopperLINK Surge Suppressor .................................................. 18
A.5 LED Status Indicators ................................................................. 18
A.6 Power Supply .............................................................................. 18
A.7 Temperature Range .................................................................... 18
A.8 Humidity ...................................................................................... 18
A.9 Dimensions ................................................................................. 18
BModel 2172 Series Factory
Replacement Parts and Accessories...................................... 19
CModel 2172 Series Interface Pin Assignment ........................ 20
C.1 10/100Base-T Interface .............................................................. 20
RJ-45.......................................................................................... 20
C.2 CopperLINK Interface ................................................................. 20

3
RJ-45.......................................................................................... 20
Terminal Block............................................................................ 20
DDistance Chart, Based on 24 AWG (0.5 MM).......................... 21

4
1.0 WARRANTY INFORMATION
Patton Electronics warrants all Model 2172 components to be free from
defects, and will—at our option—repair or replace the product should it
fail within one year from the first date of the shipment.
This warranty is limited to defects in workmanship or materials, and does
not cover customer damage, abuse or unauthorized modification. If this
product fails or does not performs as warranted, your sole recourse shall
be repair or replacement as described above. Under no condition shall
Patton Electronics be liable for any damages incurred by the use of this
product.These damages include, but are not limited to, the following: lost
profits, lost savings and incidental or consequential damages arising
from the use of or inability to use this product. Patton Electronics spe-
cifically disclaims all other warranties, expressed or implied, and the
installation or use of this product shall be deemed an acceptance of
these terms by the user.
Note Conformity documents of all Patton products can be viewed
online at www.patton.com under the appropriate product page.
1.1 COMPLIANCE
EMC Compliance:
• FCC Part 15, Class A
• EN55022, Class A
• EN55024
Safety Compliance:
• IEC/EN 60950-1
• AS/NZS 60950-1
1.2 RADIO AND TV INTERFERENCE (FCC PART 15)
This equipment generates and uses radio frequency energy, and if not
installed and used properly—that is, in strict accordance with the manu-
facturer's instructions—may cause interference to radio and television
reception. This equipment has been tested and found to comply with the
limits for a Class A computing device in accordance with the specifica-
tions in Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection from such interference in a commercial installa-
tion. However, there is no guarantee that interference will not occur in a
particular installation. If the equipment causes interference to radio or

5
television reception, which can be determined by disconnecting the
cables, try to correct the interference by one or more of the following
measures: moving the computing equipment away from the receiver, re-
orienting the receiving antenna, and/or plugging the receiving equipment
into a different AC outlet (such that the computing equipment and
receiver are on different branches).
1.3 CE DECLARATION OF CONFORMITY
We certify that the apparatus described above conforms to the require-
ments of Council Directive 2004/108/EC on the approximation of the
laws of the member states relating to electromagnetic compatibility; and
Council Directive 2006/95/EC on the approximation of the laws of the
member states relating to electrical equipment designed for use within
certain voltage limits.
The safety advice in the documentation accompanying this product shall
be obeyed. The conformity to the above directive is indicated by the CE
sign on the device.
1.4 AUTHORIZED EUROPEAN REPRESENTATIVE
D R M Green
European Compliance Services Limited.
Avalon House, Marcham Road
Abingdon,
Oxon OX14 1UD, UK
1.5 SERVICE
All warranty and non-warranty repairs must be returned freight prepaid
and insured to Patton Electronics. All returns must have a Return Materi-
als Authorization number on the outside of the shipping container. This
number may be obtained from Patton Electronics Technical Services at:
• Tel: [phone]
• Email: [email protected]
• URL: http://www.patton.com
Note Packages received without an RMA number will not be
accepted.

6
1.6 SAFETY WHEN WORKING WITH ELECTRICITY
• This device contains no user serviceable parts. The
equipment shall be returned to Patton Electronics for
repairs, or repaired by qualified service personnel.
• Mains Voltage: Ensure that the external power adapter
is a listed Limited Power Source. The mains outlet that
is utilized to power the devise shall be within 10 feet (3
meters) of the device, shall be easily accessible, and
protected by a circuit breaker. Ensure that the power
cable used meets all applicable standards for the coun-
try in which it is to be installed, and that it is connected
to a wall outlet which has earth ground.
• Hazardous network voltages are present in WAN ports
regardless of whether power to the unit is ON or OFF. To
avoid electric shock, use caution when near WAN ports.
When detaching the cables, detach the end away from
the device first.
• Do not work on the system or connect or disconnect
cables during periods of lightning activity.
In accordance with the requirements of council direc-
tive 2002/96/EC on Waste of Electrical and Electronic
Equipment (WEEE), ensure that at end-of-life you sepa-
rate this product from other waste and scrap and deliver
to the WEEE collection system in your country for recy-
cling.
This device is NOT intended nor approved for connec-
tion to the PSTN. It is intended only for connection to
customer premise equipment.
WARNING
WARNING

7
2.0 GENERAL INFORMATION
Thank you for your purchase of this Patton Electronics product. This
product has been thoroughly inspected and tested and is warranted for
one year for parts and labor. If any questions or problems arise during
installation or use of this product, contact Patton Electronics Technical
Support at [phone].
2.1 FEATURES
• Variable rate CopperLINK extender - Easy to configure
• Auto-MDIX Ethernet
• Configurable 10/100, Full/Half, and Auto-Negotiating Ethernet
• Extends network connections up to 6,000 ft (1.8 km) over 2-wire 24-
AWG unconditioned lines
• Switch selectable line rates up to 50 Mbps
• 6 symmetric or asymmetric settings via DIP switch
• Transparent operation
• LED indicators for Power, Link, and Ethernet Link & Activity
• Surge suppression up to 20 kA (8/20 μ s)
• Made in the USA
2.2 DESCRIPTION
The Patton Electronics Model 2172 CopperLink modems provide high-
speed LAN connections between peered Ethernet LANs, remote PC’s, or
any other network enabled 10/100Base-T device.
Operating in pairs, one Model 2172 is configured as the (L) Local unit
located at one end of the LAN extension and the other Model 2172 is con-
figured as the (R) Remote unit at the other end. The Model 2172 is config-
ured as a L or R via the switch on the rear panel. These units can
automatically forward LAN broadcasts, multicasts, and frames across a 2-
wire voice-grade twisted-pair link.The data is passed transparently
(unmodified) through the 2172s.The 2172s automatically add and delete
MAC addresses, only passing packets across the CopperLINK link that are
meant for the remote peered LAN.

8
Figure 1. Typical application
The pair of 2172 models work together to create a transparent extension
between two peered Ethernet LANs. Figure 1 shows a typical point-to-
point application.
3.0 INSTALLATION
To install the 2172 Ethernet Extender, do the following:
1. Connect the line interface between the units (refer to section 3.1,
“Connecting the Twisted-Pair Line Interface” on page 9)
Note See Figure 2 for the standalone unit’s rear panel arrangements.
2. Connect the Ethernet interface (refer to section 3.2, “Connecting the
10/100Base-T Ethernet Interface” on page 11).
3. Connect the power plug (refer to section 3.3, “Connecting Power” on
page 12).
The Interconnecting cables shall be acceptable for
external use and shall be rated for the proper applica-
tion with respect to voltage, current, anticipated tem-
perature, flammability, and mechanical serviceability.
CAUTION

9
Figure 2. Model 2172 standalone rear panel
3.1 CONNECTING THE TWISTED-PAIR LINE INTERFACE
The Model 2172 supports communication between two peer Ethernet
LAN sites over a distance of up to 6,000 ft (1.8 km) over 24 AWG
(0.5 mm) twisted-pair wire.
Note Actual distance and link performance may vary depending on
the environment and type/gauge of wire used.
Follow the steps below to connect the Model 2172 CopperLINK Inter-
faces.
Note The Model 2172 units work in pairs. One of the units must be
configured as a (L) Local unit, and the other unit must be config-
ured as a (R) Remote unit. It does not matter which end is the L
and which is the R. The link is always initiated by the R unit. As
long as the L unit is powered on, the R unit can establish a link
by being powered on or by having its power reset.
The Interconnecting cables shall be acceptable for
external use and shall be rated for the proper applica-
tion with respect to voltage, current, anticipated tem-
perature, flammability, and mechanical serviceability.
Line
Power
Madein theUSA
Power
Madein theUSA
Ethernet
Ethernet
2172
(RJ-45)
2172
(Terminal block)
Power
jack
Power
jack
Ethernet
port
Ethernet
port
RemLoc
Local/Remote
switch
Local/Remote
switch
RemLoc
CopperLINK twisted-pair
RJ-45 interface
CopperLINK twisted-pair
terminal block
interface
CAUTION

10
1. To function properly, the two Model 2172s must be connected
together using twisted-pair, unconditioned, dry, metal wire, between
19 (0.9mm) and 26 AWG (0.4mm). Leased circuits that run through
signal equalization equipment are not acceptable.
2. The Model 2172 is equipped with either an RJ-45 or a terminal block
interface jack that can be used on the CopperLINK interface. These
CopperLINK interfaces are a two-wire interface. Observe the sig-
nal/pin relationships on the Model 2172's CopperLINK interface jacks.
The RJ-45 connector on the Model 2172's twisted pair interface is polar-
ity insensitive and is wired for a two-wire interface. The signal/pin rela-
tionship is shown in Figure 3.
Figure 3. Model 2172 (RJ-45) twisted pair line interface.
The terminal block connector on the Model 2172's twisted pair interface
is polarity insensitive and is wired for a two-wire interface. The signal/pin
relationships is shown in Figure 4.
1 (no connection)
2 (no connection)
3 (no connection)
4 (RING)
5 (TIP)
6 (no connection)
7 (no connection)
8 (no connection)
1
2
3
4
5
6
7
8

11
Figure 4. Model 2172 (Terminal Block) twisted pair line interface.
3.2 CONNECTING THE 10/100BASE-T ETHERNET INTERFACE
The shielded RJ-45 port labeled Ethernet is the Auto-MDIX10/100Base-
T interface. This port is designed to connect directly to a 10/100Base-T
network. Figure 5 shows the signal/pin relationships on this interface.
You may connect this port to a hub or PC using a straight through or
crossover cable that is up to 328 ft long.
Figure 5. Model 2172 10/100Base-T RJ-45 Connector Pinout.
The Interconnecting cables shall be acceptable for
external use and shall be rated for the proper applica-
tion with respect to voltage, current, anticipated tem-
perature, flammability, and mechanical serviceability.
Ethernet Power
Made in the USA
RING TIP
Rem Loc
CAUTION
1 TX+/RX+
2 TX-/RX-
3 RX+/TX+
4 (no connection)
5 (no connection)
6 RX-/TX-
7 (no connection)
8 (no connection)
1
2
3
4
5
6
7
8

12
3.3 CONNECTING POWER
The Model 2172 does not have a power switch, so it powers up as soon
as it is plugged in.
An external AC or DC power supply is available separately. This connec-
tion is made via the barrel jack on the rear panel of the Model 2172. No
configuration is necessary for the power supply (See Appendix B for
domestic and international power supply and cord options).
DC power (supplied via the power supply jack to the 2172) must meet
the following requirements; DC power supplied must be regulated
+5VDC ±5%, 1.0A minimum. Center pin is +5V. The barrel type plug has
a 2.5/5.5/10mm I.D./O.D./Shaft Length dimensions.
4.0 CONFIGURATION
The Model 2172 has eight DIP switches for configuring the unit for a wide
variety of applications. This section describes switch locations and
explains the different configurations.
4.1 CONFIGURING THE HARDWARE DIP SWITCHES
Using a small flat-tip screwdriver, remove the protective cover located on
the underside of the Model 2172 (see Figure 6).
The Interconnecting cables shall be acceptable for
external use and shall be rated for the proper applica-
tion with respect to voltage, current, anticipated tem-
perature, flammability, and mechanical serviceability.
CAUTION

13
Figure 6. Removing protective cover
Figure 7 on page 13 shows the orientation of the DIP switches in the On
and Off positions.
Figure 7. DIP switch orientation
Power
Link
Ethernet
CopperLINK™
HighSpeedEthernetExtender
1234
ON
Push toggle up
for ON position
Switch toggle
Push toggle
down for
OFF position
1234
ON
S2
S2
5678
5678
S2
1234
ON
5 6 7 8
S2
RearFront

14
4.2 CONFIGURING DIP SWITCH S2
DIP switch S2 is where you configure the CopperLINK line rate, symmet-
ric or asymmetric, Ethernet, and Ethernet Shutdown. Table 1 summa-
rizes default positions of DIP switches S2-1 through S2-8. Detailed
descriptions of each switch follow the table.
Switch S2-1: Symmetric/Asymmetric Operation
Use switch S2-1 to configure the unit for symmetric or asymmetric opera-
tion..
Switches S2-2 and S2-3: Data Rate
Use switches S2-1, S2-2 and S2-3 to configure the CopperLINK line
rates.
Note See Appendix D on page 21 for line rate distances.
Table 1: S2 Summary
Position Description
S2-1 Symmetric/Asymmetric
S2-2 Line Rate
S2-3 Line Rate
S2-4 Ethernet configuration
S2-5 Ethernet configuration
S2-6 Ethernet configuration
S2-7 Ethernet Shutdown
S2-8 Remote Configuration
Table 2: Ethernet Auto Sense Selection Chart
S2-1 Setting
ON Symmetric Operation
OFF Asymmetric Operation
Table 3: Symmetric CopperLINK Line Rates Selection Chart
S2-2 S2-3 Symmetric Line Rate
ON ON 50 Mbps
ON OFF 25 Mbps
OFF OFF 10 Mbps
OFF ON Reserved

15
Note See Appendix D on page 21 for line rate distances.
Switches S2-4, S2-5 and S2-6: Ethernet Configuration
Use switches S2-4, S2-5 and S2-6 to configure Ethernet settings.
Table 4: Asymmetric CopperLINK Line Rates Selection Chart
S2-2 S2-3 Asymmetric Line Rates DS/US
ON ON 50 Mbps/2 Mbps
ON OFF 16 Mbps/2 Mbps
OFF OFF 4 Mbps/1 Mbps
Table 5: Ethernet configurations
S2-4 S2-5 S2-6 Ethernet Configurations
ON ON ON Auto-Negotiate
ON ON OFF 100Mb Full Duplex
ON OFF ON 100Mb Half Duplex
ON OFF OFF 10Mb Full Duplex
OFF ON ON 10Mb Half Duplex

16
Switch S2-7: Ethernet Shutdown
Use switch S2-7 to enable or disable Ethernet Shutdown.When Ethernet
Shutdown is enabled, the 2172 will disable the Ethernet interface when
there is no CopperLINK link detected. When Ethernet Shutdown is dis-
abled, the Ethernet interface will always be enabled.
Switch S2-8: Remote Configuration
Use switch S2-8 to enable or disable Remote Configuration.
Note The S2-8 switch applies to the R unit only. If enabled, the R will
follow the dip switch configuration of the L unit. If disabled, the R
unit will use its own dip switch setting to determine its Ethernet
operating mode and Ethernet Shutdown mode configuration.
The S2-8 switch does not affect the data rate. The data rate will
always follow the L configuration.
5.0 OPERATION
Once the Model 2172s are properly installed, they should operate trans-
parently. No user settings required. This section describes reading the
LED status monitors.
5.1 POWER UP
Before applying power to the Model 2172, please review section 3.3,
“Connecting Power” on page 12 to verify that the unit is connected to the
appropriate power source.
Table 6: Ethernet Shutdown
S2-7 Description
ON Ethernet Shutdown Enabled
OFF Ethernet Shutdown Disabled
Table 7: Ethernet Shutdown
S2-8 Description
ON Remote Configuration Enabled
OFF Remote Configuration Disabled

17
5.2 FRONT PANEL LED STATUS MONITORS
The Model 2172 features three front panel LEDs that monitor power, the
Ethernet signals, and the CopperLINK connection. Figure 8 shows the
front panel location of each LED. Table 8 on page 17 describes the LED
functions.
Figure 8. Model 2172 standalone unit front panel
Table 8: Front panel LED description
LED Description
Power Solid GREEN to indicate the unit is powered on.
Link Solid GREEN (ON) to indicate that the end-to-end
CopperLINK link between the Model 2172s is estab-
lished. The Link LED is OFF when the link is down.
Ethernet Solid GREEN indicates that 10/100Base-T Ethernet
link has been established. Flashes to indicate activity.
Power
LED
CopperLINK
Power
Link
Ethernet
Link LED
Ethernet LED
HighSpeedEthernet Extender

18
APPENDIX A
SPECIFICATIONS
A.1 LAN CONNECTION
• Shielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet
• CopperLINK Connection:
RJ-45 or Terminal Block
A.2 TRANSMISSION LINE
Two-wire unconditioned twisted pair.
A.3 COPPERLINK LINE RATE AND COPPERLINK DISTANCE
• Line Rate: 50 Mbps, symmetric upstream/downstream. Additional
symmetric and asymmetric rates are available via DIP switch settings.
• Distance: 6,000 ft (1.8 km) at 1 Mbps upstream/4 Mbps downstream
Note Distances depend on selected line rate and line conditions. See
Appendix D on page 21 for details.
A.4 COPPERLINK SURGE SUPPRESSOR
SIDACTOR with maximum current surge: 20 kA (8/20 μ s).
A.5 LED STATUS INDICATORS
• Power (Green)
• CopperLINK: Link (Green)
• Ethernet: Link (Green) & Activity (Flashing Green)
A.6 POWER SUPPLY
External AC and DC options:
• AC: 120 VAC, 220 VAC, and UI (120–240 VAC)
• DC: 12 VDC, 24 VDC and 48 VDC
• Power consumption: 450 mA at 5 VDC
A.7 TEMPERATURE RANGE
0–50°C
A.8 HUMIDITY
Up to 90% non-condensing.
A.9 DIMENSIONS
1.58H x 4.16W x 3.75D in. (10.6H x 4.1W x 8.8D cm)

19
APPENDIX B
MODEL 2172 SERIES FACTORY
REPLACEMENT PARTS AND ACCESSORIES
*Only required with optional UI power supply (08055DCUI)
Patton Model # Description
Base Models
2172/E CopperLINK Multi Rate 50 Mbps Ethernet Extender;
No power supply
2172/E-2PK CopperLINK Multi Rate 50 Mbps Ethernet Extender Kit (2 units pre-
set to local and remote); No power supply
2172/EUI-2PK CopperLINK Multi Rate 50 Mbps Ethernet Extender Kit (2 units pre-
set to local and remote); 110-240VAC
07M2172-UM
User Manual
Power Supplies
08055DCUI
08055-120-5-1
100-240VAC (+5V reg. DC/2A) Universal Input Adapter.
120 VAC (+5V reg. DC/1A) Input Adapter
12V-PSM 12 VDC Input Adapter
24V-PSM 24 VDC Input Adapter
48V-PSM 48 VDC Input Adapter
Power Cords*
0805US American Power Cord
0805EUR European Power Cord CEE 7
0805UK United Kingdom Power Cord
0805AUS Australian Power Cord
0805DEN Denmark Power Cord
0805FR France/Belgium Power Cord
0805IN India Power Cord
0805IS Israel Power Cord
0805JAP Japan Power Cord
0805SW Switzerland Power Cord

20
APPENDIX C
MODEL 2172 SERIES INTERFACE PIN ASSIGNMENT
C.1 10/100BASE-T INTERFACE
RJ-45
• Pin 1: TX+
• Pin 2: TX-
• Pin 3: RX+
• Pin 6: RX-
• Pins 4, 5, 7, 8: no connection
C.2 COPPERLINK INTERFACE
RJ-45
• Pin 4: RING
• Pin 5: TIP
• Pins 1, 2, 3, 6, 7, 8: no connection
Terminal Block
Figure 1. Model 2172 (Terminal Block) twisted pair line interface..
EthernetPower
Made in the USA
RING TIP
Rem Loc