Patton 07MSNOGA-DS5 User manual

SmartNode Open Gateway
Appliance
Quick Start Guide
Important—This is a Class A device and is intended for use in a light
industrial environment. It is not intended nor approved for use in an
industrial or residential environment.
REGULATORY MODEL NUMBER: 07MSNOGA-DS5
Part Number: 07MSNOGA-DS5, Rev. A
Revised: December 10, 2014
Sales Office: [phone]
Technical Support: [phone]
E-mail: [e-mail]
WWW: www.patton.com

2SNOGA Quick Start Guide
• Do not open the device when the power cord is con-
nected. For systems without a power switch and with-
out an external power adapter, line voltages are
present within the device when the power cord is con-
nected.
• For devices with an external power adapter, the power
adapter shall be a listed Limited Power Source The
mains outlet that is utilized to power the device shall
be within 10 feet (3 meters) of the device, shall be eas-
ily accessible, and protected by a circuit breaker in
compliance with local regulatory requirements.
• For AC powered devices, ensure that the power cable
used meets all applicable standards for the country in
which it is to be installed.
• For AC powered devices which have 3 conductor power
plugs (L1, L2 & GND or Hot, Neutral & Safety/Protec-
tive Ground), the wall outlet (or socket) must have an
earth ground.
• For DC powered devices, ensure that the interconnect-
ing cables are rated for proper voltage, current, antici-
pated temperature, flammability, and mechanical
serviceability.
• WAN, LAN & PSTN ports (connections) may have haz-
ardous voltages present regardless of whether the
device is powered ON or OFF. PSTN relates to inter-
faces such as telephone lines, FXS, FXO, DSL, xDSL,
T1, E1, ISDN, Voice, etc. These are known as “hazard-
ous network voltages” and to avoid electric shock use
caution when working near these ports. When discon-
necting cables for these ports, detach the far end con-
nection first.
• Do not work on the device or connect or disconnect
cables during periods of lightning activity.
In accordance with the requirements of council directive
2002/96/EC on Waste of Electrical and Electronic Equip-
ment (WEEE), ensure that at end-of-life you separate this
product from other waste and scrap and deliver to the
WEEE collection system in your country for recycling.
WARNING

SNOGA Quick Start Guide 3
1.0 What’s Included With the SNOGA
1. SNOGA
2. AC Power Adaptor
3. INS-KIT-2
•1 x D89 to RJ45 control port Adaptor (EIA-561)
•2 x RJ45 Cables 10ft
•Rubber Feet
4. Rack Ears and Hardware (already installed)
5. Electrical Safety Notice
6. Quick Start Guide
2.0 Steps for Setting Up the SNOGA
1. Plug a mouse into USB
2. Plug a keyboard into USB
3. Plug a monitor into either VGA or HDMI
4. Plug the power adaptor into the power connector on the back of the unit
Note Make sure the power adaptor is plugged in ALL the way and the
connector in locked in.
Figure 1. SNOGA basic connections

4SNOGA Quick Start Guide
3.0 Basic Application
Figure 2. SNOGA Application
Note Your favorite 3rd party switch is required for communication between
the SmartNode and the integrated PC.
4.0 List of SNOGA SKU’s and Their Related SmartNodes
Note For all SKU's please refer to the SmartWare CLI guide for information on
the SmartNode Command Line Interface and commands:
http://www.patton.com/manuals/07MSWR66_SCG-UM.pdf
Product SKU Related SmartNode
SNOGA/1E15V/EUI SN4981/1E15V/EUI
SNOGA/1E30V/EUI SN4981/1E30V/EUI
SNOGA/4E15VR/EUI SN4981/4E15VR/EUI
SNOGA/4BIS8V/EUI SN4661/4BIS8V/EUI
SNOGA/2BIS2JS2JO8V/EUI SN4661/2BIS2JS2JO8V/EUI
SNOGA/4BIS4JS4JO12V/EUI SN4661/4BIS4JS4JO12V/EUI
SNOGA/4JS4JO/EUI SN4660/4JS4JO8V/EUI
SNOGA/8BIS16V/EUI SN4661/8BIS16V/EUI
SNOGA/8JS/EUI SN4660/8JS8V/EUI

SNOGA Quick Start Guide 5
5.0 SmartNode Ports
5.1 SN 4600 Series
5.2 SN 4980 Series
Default IP Address:
192.168.1.1
T1/E1
PRI ports 0/3–0/0
ETH 0/0
10/100/1000Base-T port
RESET button
Console
RS-232 port
ETH 0/1
10/100/1000Base-T port
RS-232
ConsoleETH 0/0ETH 0/1
Reset
0/00/10/20/3
T1/E1

6SNOGA Quick Start Guide
A.0 Specifications
B.0 Compliance Information
B.1 Compliance
•EMC: EN55022 and EN5502
•FCC Part 15 Class A; Part 68; CS-03
•CE
•Safety: EN 60950
2.2 Radio and TV Interference (FCC Part 15)
This equipment generates and uses radio frequency energy, and if not installed and
used properly—that is, in strict accordance with the manufacturer's instructions—may
cause interference to radio and television reception. This equipment has been tested
and found to comply with the limits for a Class A computing device in accordance with
the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide
reasonable protection from such interference in a commercial installation. However,
there is no guarantee that interference will not occur in a particular installation. If the
equipment causes interference to radio or television reception, which can be deter-
mined by disconnecting the cables, try to correct the interference by one or more of the
following measures: moving the computing equipment away from the receiver, re-ori-
enting the receiving antenna, and/or plugging the receiving equipment into a different
AC outlet (such that the computing equipment and receiver are on different branches).
CPU / Socket Intel Celeron J1900 2.0/2.41 GHz
TDP 10 W
Memory 2x DDR3L SODIMM
Storage 1x mSATA (full size)
Graphics Intel HD 688/854 MHz
Video Signal 1x VGA, 1x HDMI
Network & Wireless 2x LAN 1000
I/O 8-bit DIO
Cooling Passive
Operating Temperature 0 to 60°C
Form Factor Mini-ITX
Length 170 (mm)
Width 170 (mm)
Input Power 12 DC V

SNOGA Quick Start Guide 7
B.3 CE Declaration of Conformity
Product Description: SmartNode Open Gateway Appliance
This equipment conforms to the requirements of Council Directive 1999/5/EC on the
approximation of the laws of the member states relating to Radio and Telecommunica-
tion Terminal Equipment and the mutual recognition of their conformity and the Direc-
tive 2011/65/EC relating to RoHS compliance.
The signed Declaration of Conformity can be downloaded from www.patton.com/certi-
fications/.
B.4 Authorized European Representative
D.R.M. Green
European Compliance Services Limited.
Avalon House, Marcham Road
Abingdon, Oxon OX14 1UD, UK
Copyright statement
Copyright © 2014, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electron-
ics assumes no liability for errors that may appear in this document.
Trademarks statement
The term SmartNode is a trademark of Patton Electronics Company. All other trade-
marks presented in this document are the property of their respective owners.
Patton support headquarters in the USA
•Online support: Available at www.patton.com
•E-mail support: E-mail sent to [email protected] will be answered within 1 busi-
ness day
•Telephone support: Standard telephone support is available five days a week—from
8:00 am to 5:00 pm EST (1300 to 2200 UTC/GMT)—by calling [phone]
•Support via VoIP: Contact Patton free of charge by using a VoIP ISP phone to call
sip:[email protected]
•Fax: [phone]
The safety advice in the documentation accompanying the
products shall be obeyed. The conformity to the above direc-
tive is indicated by the CE sign on the device.

8SNOGA Quick Start Guide
Alternate Patton support for Europe, Middle East, and Africa
(EMEA)
•Telephone support: Standard telephone support is available five days a week—from
9:00 am to 12:00 pm & 1:30 pm to 5:30 pm CET (0800 to 16:30 UTC/GMT)—by
calling [phone]
•Fax: [phone]
Warranty, Trademark, & Compliance Information
For warranty, trademark and compliance information, refer to the SmartNode Series
data sheet available Online at http://www.patton.com/datasheet/SNOGA_data-
sheet.pdf.