Patton SmartNode 4554 User manual

SmartNode 4554™
ISDN BRI PSTN Gateway
Quick Start Guide
Important
—This is a Class A device and is intended for use in a light industrial environment. It is not
intended nor approved for use in an industrial or residential environment.
Document Number: 13236U7-001 Rev. B
Part Number: 07MSN4554-QS
Revised: July 13, 2007
Sales Office: [phone]
Technical Support: [phone]
E-mail: [email protected]
WWW: www.patton.com

2 SmartNode 4554 Quick Start Guide
1.0 Power up the SmartNode
1. Connect the SN4554 to a power source using the included power supply and cable.
2. When the Power LED stops blinking and remains lit, the SN4554 is ready to configure.
• The SmartNode 4554 contains no user serviceable parts. The equip-
ment shall be returned to Patton Electronics for repairs, or repaired
by qualified service personnel.
• Mains Voltage: Do not open the case the power cord is attached. The
external power adaptor shall be a listed limited power source that
incorporates a disconnect device and shall be positioned within easy
reach of the operator. The mains outlet shall be within 10 feet (3
meters) of the device, shall be easily accessible, and protected by a
circuit breaker.
• The SmartNode 4554 is not shipped with power cables. For AC pow-
ered units, ensure that the power cable used meets all applicable
standards for the country in which it is to be installed, and that it is
connected to a wall outlet which has earth ground.
• Hazardous network voltages are present in WAN ports regardless of
whether power to the SmartNode 4554 is ON or OFF. To avoid elec-
tric shock, use caution when near WAN ports. when detaching the
cables, detach the end away from the SmartNode 4554 first.
• Do not work on the system or connect or disconnect cables during
periods of lightning activity.

SmartNode 4554 Quick Start Guide 3
2.0 Connect the SmartNode to your
local network
You must connect the SN4554 to an IP network that provides a DHCP server. Using the included black Ethernet
cable, connect the SN4554 RJ-45 Ethernet WAN port, labeled ETH (see figure 1 ), to an Ethernet hub or switch
on the same network as your PC. The Ethernet WAN interface is configured as a DHCP client.
Figure 1. Connecting the SN4554 to the network via a hub or switch
The interconnecting cables shall be acceptable for external use and shall be rated for
the proper application with respect to voltage, current, anticipated temperature, flam-
mability, and mechanical serviceability.
CAUTION
Ethernet Hub
or Switch
PC
DHCP
Server
LAN ISDN 2 ISDN 1
SN4554
ETH
port

4 SmartNode 4554 Quick Start Guide
3.0 Connect the SmartNode to an ISDN NT
1. Using a straight-though cable, terminated with RJ-45 connectors, connect the BRI port of your SN4554 to
a PBX or ISDN NT, as shown below:
The interconnecting cables shall be acceptable for external use and shall be rated for
the proper application with respect to voltage, current, anticipated temperature, flam-
mability, and mechanical serviceability.
CAUTION
LAN ISDN 2 ISDN 1
RJ-45, male RJ-45, male
3
4
5
6
3
4
5
6
ISDN NT
or PBX

SmartNode 4554 Quick Start Guide 5
4.0 Start the SmartNode Discovery Tool
1. Insert the CD included with your SN4554 into the CD drive on your PC.
2. Copy the file named SNDiscovery.exe from the CD to your PC.
3. At your PC, double-click the SNDiscovery.exe file name to activate the tool. The SmartNode Discovery Tool
window will display the IP Address, MAC Address, Device Type (model number) and Build (software
release) of your SN4554.
If your SN4554 does not appear:
• Make sure the SN4554 and your PC are on the same routed subnet
• Make sure any firewall programs on your PC are disabled
5.0 Access the Web Browser (GUI) Interface
1. In the SmartNode Discovery Tool window, select the line that displays the IP address of your SN4554.
Figure 2. SmartNode Discovery Tool window

6 SmartNode 4554 Quick Start Guide
2. Right-click the selected line, and select Webbrowser . The Login window will display.
Figure 3. Login window
3. Enter the username administrator . Do not enter a password. Instead simply click OK. Your web browser will
display the SN4554 home page.
Figure 4. SN4554 home page
6.0 Configuring your SmartNode
Once you have logged in you can use the browser-based graphical user interface (GUI) to configure and manage
your SN4554. The SN4554 home page displays three Immediate Actions buttons that allow you to store the cur-
rent configuration state, reload the device, and restore to factory defaults. The home page also displays certain
basic system information. You can always return to the home page by clicking Home in the navigation bar.

SmartNode 4554 Quick Start Guide 7
The GUI consists of the following main elements:
•
The “Navigation Bar” on the left edge presents you with a menu listing giving access to the various configura-
tion and status pages of the SN4554.
•
At the top of the page you see the “Current System Path” which displays the location and element currently
presented in the main area.
•
The rest of the page displays the configuration and status information for the different features of
the SN4554.
7.0 Additional Information
Refer to the SmartNode 4554 Getting Started Guide located on the CD-ROM shipped with your SN4554 device and
available online at www.patton.com/manuals. For detailed information about:
•
Installing, configuring, operating, and troubleshooting.
• Warranty, trademark & compliance
The CD-ROM also includes many freeware and shareware tools, including TFTP servers, and Telnet clients.
A.0 Customer and Technical Support
Toll-Free VoIP support: call sip:[email protected] with a VoIP SIP client
Online support: www .patton.com
E-mail support: [email protected] —answered within 1 business day
Telephone support:
• Standard: [phone] (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to
2200 UTC/GMT)
•
Alternate: [phone] (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800
UTC/GMT)
Fax: [phone] (USA) or [phone] ( Switzerland)
Whenever you modify the configuration your SN4554, immediately applies your
changes.Howver, your new settings ARE NOT PERMANENTLY SAVED (in non-volatile
memory [RAM]). To survive power failure or manual reload you must store your new
settings in non-volatile memory. To save your changes: return to the home page and
press the Save Current Configuration button.
IMPORTANT

8 SmartNode 4554 Quick Start Guide
B.0 Appendix—Factory default IP addresses
Factory default IP addresses and netmask configuration.
C.0 Compliance Information
C.1 Compliance
EMC Compliance:
•
EN55022, Class A
• EN55024
Safety Compliance:
•
IEC 60950-1
•
EN60950-1
•
AS/NZS 60950
Telecom:
•
TBR3
•
AS/ACIF S031
•
NZ ISDN Layer 3 Supplement
IP Address Network mask
WAN interface Ethernet 0 (0/0) DHCP Client n/a
LAN interface Ethernet 1 (0/1) 192.168.1.1 255.255.255.0
DHCP server address range (LAN) 192.168.1.10-192.168.1.99 255.255.255.0

SmartNode 4554 Quick Start Guide 9
C.2 EC Declaration of Conformity
(See section C.3 “EG-Konformitätserklärung” for German version.)
Product Description: SmartNode 4554
The products described above in the form as delivered are in conformity with the provisions of the following
European Directive:
R&TTE Directive 1999/5/EC
Guidelines of the European Parliament and the Committee for the Harmonization of the Legal Regu-
lations of the Member States concerning radio equipment and telecommunications terminal equip-
ment and the mutual recognition of their conformity.
The signed Declaration of Conformity can be downloaded from www.patton.com/certifications/.
The safety advice in the documentation accompanying the products shall be obeyed.
The conformity to the above directive is indicated by the CE sign on the device.

10 SmartNode 4554 Quick Start Guide
C.3 EG-Konformitätserklärung
(see section C.2 “EC Declaration of Conformity” for English version)
Produktbezeichnung : SmartNode 4554
Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften fol-
gender Richtlinie überein:
R&TTE 1999/5/EG
Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der
Mitgliedstaaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige
Anerkennung ihrer Konformität.
Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/
certifications/.
C.4 Authorized European Representative
D R M Green
European Compliance Services Limited.
Oakdene House, Oak Road
Watchfield,
Swindon, Wilts SN6 8TD, UK
Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten.
Die Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem
Gerät bestätigt.

SmartNode 4554 Quick Start Guide 11
Copyright statement
Copyright © 2007, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Electronics assumes no
liability for errors that may appear in this document.
Trademarks statement
The term SmartNode is a trademark of Patton Electronics Company. All other trademarks presented in this docu-
ment are the property of their respective owners.
Warranty
For warranty information, refer to the SmartNode 4554 Getting Started Guide located on the CD-ROM that came
with your IAD or available online at www.patton.com .
In accordance with the requirements of council directive 2002/96/EC on Waste of
Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate
this product from other waste and scrap and deliver to the WEEE collection system in
your country for recycling.

12 SmartNode 4554 Quick Start Guide
NOTES
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________