Patton SmartNode 4900 User manual

SmartNode 4900
IpChannel Bank
Quick Start Guide
Sales Office: [phone]
Technical Support: [phone]
E-mail: suppor[email protected]
WWW: www.patton.com
Document Number: 13217U7-001 Rev. C
Part Number: 07MSN4900-QS
Revised: January 13, 2010
Start Installation
For Quick
Start Installation
For Quick
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

Patton Electronics Company, Inc.
7622 Rickenbacker Drive
Gaithersburg, MD 20879 USA
Tel: [phone]
Fax: [phone]
Support: [phone]
Web: www.patton.com
E-mail: suppor[email protected]
Trademark Statement
Patton, the Patton logo, and SmartNode are registered trademarks of Patton Electronics
Company. The terms SmartWare and SmartView Management Center are trademarks of
Patton Electronics Company. All other trademarks presented in this document are the
property of their respective owners.
Copyright © 2010, Patton Electronics Company. All rights reserved.
The information in this document is subject to change without notice. Patton Elec-
tronics assumes no liability for errors that may appear in this document.
In no event shall Patton Electronics or its employees and associated companies be lia-
ble for any incidental, special, indirect or consequential damages whatsoever, including
but not limited to lost profits, arising out of or related to this manual or the informa-
tion contained within it, even if Patton Electronics has been advised of, known, or
should have known, the possibility of such damages.
Important Information
To use virtual private network (VPN) and/or AES/DES/3DES encryption capabilities
with the SmartNode 4900, you may need to purchase additional licenses, hardware,
software, network connection, and/or service. Contact [email protected] or
[phone] for assistance.
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

Introduction 3
SmartNode 4900 Quick Start Guide
Introduction
This Quick Start Guide leads you through the basic steps to set up a new SmartNode and to download a con-
figuration. Please note that this guide does not replace the detailed Software Configuration Guide and the Get-
ting Started Guide on the CD-ROM and available online at www.patton.com/voip .
SmartNodes can be used for a wide variety of IP and voice over IP applications. To support and ease the config-
uration of the SmartNodes configuration templates for the most important applications are available online at
http://www.patton.com/voip/appnotes.shtml .
Setting up a new SmartNode consists of the following steps:
1. Attach the power cable retainer clips to the unit
2. Connect a PC to the SmartNode, log in and configure your LAN IP address (see page 4 for details)
3. Connect the SmartNode to the LAN (see page 6)
4. Download a configuration example, adapt it to your network, and load it onto the SmartNode (see page 7)
Attaching the cable retainer clips
To secure the power cord, it is necessary to attach the metal retainer clips (if applicable to your model). Squeeze
the clip and insert into the holes in the screws on either side of the power connector on your unit. The clip will
pop into place.
Figure 1. Attaching the cable retainer clips
Note
Refer to the Getting Started Guide on the CD-ROM or on the Patton
website for detailed instrauctions about grounding and connecting
power to your unit.
For FXO (/JO) models: To maintain CE/EMC compliance,
attach the included snap-on ferrite clamp (Patton P/N 0818S-
02) to the 64/50 pin telco cable (not included but available
upon request) about four inches away from the FXO box telco
port connector.
IMPORTANT
Power cable
retainer clip
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

Connecting a PC, logging in, and configuring the LAN IP address 4
SmartNode 4900 Quick Start Guide
Connecting a PC, logging in, and configuring the LAN IP address
Connecting power and configuring the default IP address
Connect the SmartNode to the mains power supply using the included power supply and cable. When the
RUN LED stops blinking and remains lit, the SmartNode is ready.
The factory default IP settings are listed in table 1. If these addresses do not work with your network they must
be changed. Contact your network administrator if you are not sure which IP address to use in
your installation.
Note
The DHCP server is running on the ETH 0/1 of the SN4900 Series
models. All Ethernet ports are pre-configured and active.
Connecting to a PC and logging in
1. To access the SmartNode configuration, connect a PC equipped with an RS-232 console port to the Con-
sole port on the front of the SmartNode. Use the included black Ethernet cable and RJ45 to DB-9 adapter
for this purpose (Model 16F-561).
Figure 2. Connecting to the PC
2. Open a Terminal connection to the SmartNode. Use the Terminal program included with most PC operat-
ing systems (e.g. Hyper Terminal on Windows). The CD-ROM also includes some recommended termi-
nal programs.
Table 1. Factory default IP address and network mask configuration
Item IP Addresss(es) Network Mask
WAN interface Ethernet 0 (ETH 0/0) DHCP DHCP
LAN interface Ethernet 1 (ETH 0/1) 192.168.1.1 255.255.255.0
DHCP server address range 192.168.1.10-192.168.1.19 255.255.255.0
100-240V
(50-60 Hz)
1 AMP
UNITEQUIPPED WITH DUAL SUPPLIES
DISCONNECTBOTH SUPPLIES
BEFORESERVICING
UNITEQUIPPED WITH DUAL SUPPLIES
DISCONNECTBOTH SUPPLIES
BEFORESERVICING
100-240V
(50-60 Hz)
1 AMP
ETH 0/0
NIC ADDRESS
00:A0:BA:00:04:10
Console Telco Ports
50
1
Reset
ExpansionETH 0/1
Status Activity
Console port
Laptop PC
Model 16F-561
adapter and cable
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

Connecting a PC, logging in, and configuring the LAN IP address 5
SmartNode 4900 Quick Start Guide
3. Type administrator as the login prompt and press the Enter key after the password prompt (do not type
anything for the password). A prompt will appear consisting of the IP address and > character.
login: administrator
password:
172.16.40.1>
4. Following log in, the SmartNode is in operator execution mode (indicated by > character in the command
line prompt). With the commands enable and configure , you enter the configuration mode.
172.16.40.1> enable
172.16.40.1# configure
172.16.40.1(cfg)#
Changing the IP address
1. Select the context IP mode to configure an IP interface.
172.16.40.1(cfg)# context ip router
172.16.40.1(ctx-ip)[router]#
2. Set the IP address and network mask for the each IP interface ( eth0 , for example).
Note For the examples in this guide, a private network ( 172.16.1 ) IP
address is used.
172.16.40.1(ctx-ip)[router]# interface eth0
172.16.40.1(if-ip)[eth0]# ipaddress 172.16.1.10 255.255.255.0
2002-10-29T00:09:40 : LOGINFO : Link down on interface eth0.
2002-10-29T00:09:40 : LOGINFO : Link up on interface eth0.
172.16.1.10(if-ip)[eth0]#
3. Make this modified configuration your new start-up configuration. On the next start-up the system will
initialize itself using the modified configuration.
172.16.1.10 (if-ip)[eth0]# copy running-config startup-config
172.16.1.10 (if-ip)[eth0]#
Go to section “Connecting the SmartNode to the LAN” on page 6 to connect the SmartNode to
your network.
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

Connecting the SmartNode to the LAN 6
SmartNode 4900 Quick Start Guide
Connecting the SmartNode to the LAN
The 4900 Ethernet ports are auto MDX, therefore a straight-through wired cable can be used for host and
switch connections (see figure 3).
Figure 3. Connecting the SmartNode to the network
You can check the connection with the ping command to another host on the local LAN.
172.16.1.99(if-ip)[eth0]#ping <IP Address of the host>
Respectively from the host: ping 172.16.1.99
Note
To ping outside your local LAN, you will need to configure the
default gateway.
You may now start to configure the SmartNode from scratch using the CLI commands, but we recommend
that you start your configuration from a template. See “Downloading a configuration example, adapting it to
your network, and loading it onto the SmartNode” on page 7 for further details.
For a detailed description of the CLI refer to the SmartWare Software Configuration Guide (SCG) available on
the CD-ROM and online at: www.patton.com/voip .
100-240V
(50-60 Hz)
1 AMP
UNITEQUIPPED WITH DUAL SUPPLIES
DISCONNECTBOTH SUPPLIES
BEFORESERVICING
UNITEQUIPPED WITH DUAL SUPPLIES
DISCONNECTBOTH SUPPLIES
BEFORESERVICING
100-240V
(50-60 Hz)
1 AMP
ETH 0/0
NIC ADDRESS
00:A0:BA:00:04:10
Console Telco Ports
50
1
Reset
ExpansionETH 0/1
Status Activity
LAN (ETH 0/1)
Network
interface
PC or workstation
or Telnet
LAN
Internet or
WAN (optional)
WAN
(ETH 0/0)
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

Downloading a configuration example, adapting it to your network, and loading it onto the SmartNode 7
SmartNode 4900 Quick Start Guide
Downloading a configuration example, adapting it to your network,
and loading it onto the SmartNode
Patton provides a collection of configuration templates on the CD-ROM that came with the SmartNode
device—and also on the support page at www.patton.com/voip/appnotes.shtml —one of which may be simi-
lar enough to your application that you can use it to speed up configuring the SmartNode. Simply download
the configuration note that matches your application to your PC. Adapt the configuration as described in the
configuration note to your network (remember to modify the IP address) and copy the modified configuration
to a TFTP server. The SmartNode can now load its configuration from this server.
Note Patton regularly adds new configuration templates to the collection at
www.patton.com/voip/appnotes.shtml, so if you do not see your applica-
tion on the CD-ROM, it may have been added to the website.
Note If your application is unique and not covered by any of Patton’s configura-
tion templates, you can manually configure the SmartNode instead of load-
ing a configuration file template. In that case, refer to the SmartNode Series
SmartWare Software Configuration Guide for information on configuring the
SmartNode device.
In this example we assume the TFTP server on the host with the IP address 172.16.1.11 and the configuration
named SN.cfg in the root directory of the TFTP server.
172.16.1.99(if-ip)[eth0]#copy tftp://172.16.1.11/SN.cfg startup-config
Download...100%
172.16.1.99(if-ip)[eth0]#
After the SmartNode has been rebooted the new startup configuration will be activated.
172.16.1.99(if-ip)[eth0]#reload
Running configuration has been changed.
Do you want to copy the 'running-config' to the 'startup-config'?
Press 'yes' to store, 'no' to drop changes : no
Press 'yes' to restart, 'no' to cancel : yes
The system is going down
Additional information
For detailed information about configuring and operating guidance, set up procedures, and troubleshooting,
refer to the SmartNode Series SmartWare Software Configuration Guide and the SmartNode Getting Started Guide
on the enclosed Patton VoIP CD-ROM or at http://www.patton.com/voip/. On the CD-ROM you will also
find numerous freeware and shareware tools, including TFTP servers, Telnet clients, etc..
When you issue the reload command, the SmartNode will ask
if you want to copy the running configuration to the startup con-
figuration. Since you just downloaded a configuration file to the
startup configuration you must answer this question with NO.
Otherwise, the downloaded configuration will be overwritten
and lost!
IMPORTANT
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]

Certifications and approvals 8
SmartNode 4900 Quick Start Guide
Certifications and approvals
EC Declaration of Conformity
(see section “EG-Konformitätserklärung” for German version)
Product Description: SmartNode 4900
The products described above in the form as delivered are in conformity with the provisions of the following
European Directive:
R&TTE Directive 1999/5/EC
Guidelines of the European Parliament and the Committee for the Harmonisation of the Legal Regula-
tions of the Member States concerning radio equipment and telecommunications terminal equipment and
the mutual recognition of their conformity.
The signed Declaration of Conformity can be downloaded from www.patton.com/certifications/
EG-Konformitätserklärung
(see section “EC Declaration of Conformity” for English version)
Produktbezeichnung: SmartNode 4900
Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften
folgender Richtlinie überein:
R&TTE 1999/5/EG
Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der Mit-
gliedstaaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige
Anerkennung ihrer Konformität.
\
Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/certifications/
The safety advices in the documentation accompanying the products shall be obeyed. The
conformity to the above directive is indicated by the CE sign on the device.
Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten. Die
Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem
Gerät bestätigt.
VoIPon www.voipon.co.uk [email protected] Tel: [phone] Fax: [phone]