PAX A920 User manual

Terminal Charging Base
for PAX A920
Installation Guide



January, 2022

Contents
Introduction............................................................................................................................................... 3
Charging Base Overview .......................................................................................................................... 4
Requirement......................................................................................................................................... 4
Overview.............................................................................................................................................. 5
Charging Base Installation........................................................................................................................ 6
Installing the Terminal Silicone Sleeve ............................................................................................... 6
Installing the Terminal Charging Base................................................................................................. 7
Using the Charging Base .......................................................................................................................... 9
Using the Charging Base ..................................................................................................................... 9
LED Status Light ............................................................................................................................... 10

Terminal Charging
Base for PAX A920 Installation Guide
Copyright© 2021 PayFacto Inc. Page 3of10
Introduction
This document explains how to install the charging base for the PAX A920 terminal and included
silicone sleeve. The charging base makes it easy to recharge the terminal without having to remove the
siliconesleevetoensurethatthemicro-USBconnectorisproperlyseatedintheterminal’scharging
port.
NOTE: The terminal must be fitted with the PayFacto-
branded silicone sleeve for the best results. The
PayFacto silicone sleeve displays the PayFacto logo on
the back. You should not use the charging base for any
terminal not protected by the silicone sleeve.
This setup guide describes the following topics:

Charging Base Requirement
•
Charging Base Overview
•
◦
◦
Charging Base Installation
Install Terminal Silicone Sleeve
Install Terminal Charging Cable
•
◦
◦
Working with the Charging Base
Using the Charging Base
LED Status Light
•

Terminal Charging
Base for PAX A920 Installation Guide
Copyright© 2021 PayFacto Inc. Page 4of10
Requirement
To ensure the best charging results, you must use the original AC power adapter that came with
your PAX A920 terminal. The AC power adapter should have the PAX logo printed on one side as
shown below:

Terminal Charging
Base for PAX A920 Installation Guide
Copyright© 2021 PayFacto Inc. Page 5of10
Overview
Your PAX A920 terminal charging base includes the following components:
Charging base
1.
6-foot (180cm) USB to micro-
USB cable
2.
Protective silicone sleeve
3.

Terminal Charging
Base for PAX A920 Installation Guide
Copyright© 2021 PayFacto Inc. Page 6of10
1.
2.
3.
Installing the Terminal Silicone Sleeve
To protect your PAX A920 terminal from minor impact damage, you should install the silicone sleeve provided
with the terminal charging base as the charging base is designed specifically for terminals with the sleeve.
To install the silicone sleeve:
Insert the top of the terminal under the front-facing camera protection until the sleeve fits snugly onto
the terminal’s top.
Pull the bottom of the sleeve over the bottom edge of the terminal.
Repeat for any additional terminals you intend to place on the charging base.
NOTE: To add or change a SIM card, you need to remove
the sleeve from the terminal.

Terminal Charging
Base for PAX A920 Installation Guide
Copyright© 2021 PayFacto Inc. Page 7of10
1.
2.
Installing the Terminal Charging Base
Before you install and connect thecharging base, make sure that the desired location is within
reach of an AC outlet and that there is enough space to for the charging base and the terminal
when connected.
To install the charging base:
Turn the charging base over and locate the micro-USB port.
Insertthecable’smicro-USBplugintothebase’sport.

Terminal Charging
Base for PAX A920 Installation Guide
Copyright© 2021 PayFacto Inc. Page 8of10
3.
4.
5.
Secure the cable in the guide at the top of the charging base and turn the charging base over.
Connectthecable’sUSBplugintotheACadapter’sUSBport.
Plug the adapter into an AC outlet. The LED at the bottom edge of the base lights up.

Terminal Charging
Base for PAX A920 Installation Guide
Copyright© 2021 PayFacto Inc. Page 9of10
Using the Charging Base
To use the charging base, you need only place the terminal(s) on the base so the printer rests in the cradle at
the top of the charging base. If the status light remains blue after you place the terminal on the base, the
terminal is not seated correctly, and not connecting to the charging base’s gold pins.

Terminal Charging
Base for PAX A920 Installation Guide
Copyright© 2021 PayFacto Inc. Page 10of10
LED Status Light
The LED at the bottom edge of the charging base indicates the terminal’s charging status:
Blue: Charging base is plugged in, no
terminal connected.
Red/Yellow: Terminal is charging.
Green: Terminal is fully charged.