PB TEEN Beadboard Study Armoire User manual

www.pbteen.com
Beadboard Study Armoire
Pre-assembly:
•Please read all instructions before beginning
assembly.
•Two-person assembly is recommended.
•Save all packing materials until assembly is
complete to avoid accidentally discarding
smaller parts or hardware.
Parts included:
A– Armoire Top – 1 pc B – Armoire Base – 1 pc
Hardware Included:
C– Hex Bolt – 7 pcs D– Allen Key – 1 pc E– Wooden Dowel – 4 pcs
Tools Required:
Phillip Screwdriver (not included)
Assembly:
1. On a soft, scratch-free surface, such as a carpet or rug, remove parts from box.
2. Set up Armoire Base (B) in your desired place. Insert Wooden Dowels (E) into pre-drilled holes on
each corner of top. Pull out keyboard tray by pushing plastic button on both side glider as shown
in Fig 1.
Fig 1 Fig 2

www.pbteen.com
3. Carefully put Armoire Top (A) onto Armoire Base (B) by aligning the other end of Wooden Dowels
(E) with pre-drilled holes underneath bottom of Armoire Top (A).Open Armoire Base (B) doors,
insert Hex Bolts (C) through pre-drilled holes at the bottom of Armoire Base (B) top frame into
pre-drilled holes at the bottom of Armoire Top (A), tighten with Allen Key (D) as shown in Fig 2.
4. Put keyboard tray back into the Armoire Base (B) as shown in Fig 3.
5. Adjust the recessed levelers located at the base of each leg to keep the unit level as shown in Fig
3.
6. Adjustable shelves are pre-fixed. You can adjust the shelves by following steps below:
** Before removing the shelves, unscrews and remove screws, which are attached to shelf pegs
on the underside of the shelves, with a Phillips Head Screwdriver;
** Determine desired height for shelves using corresponding peg holes located on the interior
inside of the Armoire;
** Insert shelf pegs into the pre-drilled holes until fully secured. Place shelves onto the shelf pegs,
making sure shelves are stable. Reinsert and tighten screws back into the shelves by inserting the
screws though pre-drilled holes of shelf pegs into underside of the shelf. See Fig 4.
7. Hardware should be checked periodically for tightness.
Fig 3 Fig 4
Care Instructions:
•Avoid direct sunlight and excessive
temperatures.
•Dust often using a clean, soft, dry and lint-
free cloth.
•Slightly moisten cloth with water. A damp
cloth holds dust and prevents scratching.
•Waxing is not recommended on lacquered
finish.

www.pbteen.com
FURNITURE TIPPING RESTRAINT
WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision.
Manufacturer assumes no liability for improper installation or excessive loads placed on screws,
brackets or straps.
Young children may be injured by tipping furniture and the use of a tipping restraint is highly
recommended.
When properly installed, this restraint could provide protection against the unexpected tipping of
furniture. We recommend mounting this restraint to a wall stud.
Hardware included:
•(2) Brackets 48 x 21 x 10mm
•(1) Nylon Strap 300 x 12 x 8mm
•(2) Stud Mounting Screws 6 x 32mm
•(2) Product Side Mounting Screws 6 x 19mm
Note: For safe mounting it is essential to use the proper hardware for your wall type.
The included hardware is for drywall or stud mounting only. For other wall
types (ie: plaster, concrete, brick…) please consult your local hardware store.
1. Determine the final resting position of the furniture piece. Mark
location on the wall approximately 1” below the top of the back
of the furniture. Mark and drill pilot hole into the center of the
stud with a 3/32” drill bit. Attach a bracket to the stud with the
long screws provided.
2. On the back of the furniture, a bracket will need to be attached
to the furniture frame at the top. To do this, temporarily move
the furniture into its final position and mark the location of the
wall bracket on the furniture frame.
3. Move the furniture away from the wall and place a bracket on
the mark. Mark and drill holes for screws with a 3/32” drill bit.
Attach the bracket to the furniture with the short screws
provided.
4. Check to be sure the wall bracket is firmly screwed into wall
stud and the furniture bracket is firmly attached to the frame.
5. Move the piece of furniture into its final position so that the wall
bracket and furniture bracket are in alignment.
6. Thread the strap through brackets and tighten until snug. Do
not over- tighten.
7. Check to make sure the brackets are firmly installed and the
strap is secure.
Completed Anti-tip Kit Installation
Stud
Wallboard
Furniture Frame
Furniture Frame
Stu
d
Wallboard