RIGHT ANGLE NewHeights 4 Series User manual

Instruction #53430 • Dated: 02/21/2019
NewHeights™ Series 4 Eciente LT Flip
Workstation Assembly Instructions
Warranty: raproducts.com/warranty
1 of 12

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 2 of 12
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
USE THIS PRODUCT ONLY AS INSTRUCTED.
FAILURE TO COMPLY WITH ALL INSTRUCTIONS AND WARNINGS
MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY.
Basic Safety Instructions
1. Intended Use. This Product is exclusively designed for use as indoor ofce furniture in compliance with all instructions and safety warnings
in the user manual. Any different use, or use extending beyond the intended use, may result in property damage or bodily injury and is
prohibited. This Product should not be used, operated or maintained with additional components not authorized by K&A Manufacturing, Inc.
BY USING THIS PRODUCT OR ANY FEATURE OF THIS PRODUCT, YOU AGREE TO COMPLY WITH ALL PRODUCT TERMS
AND POLICIES, INCLUDING WITHOUT LIMITATION ANY SAFETY WARNINGS AND INSTRUCTIONS, PROVIDED BY
K&A MANUFACTURING, INC. AND ITS AFFILIATES. K&A MANUFACTURING, INC. SHALL ASSUME NO LIABILITY FOR ANY
DAMAGE OR INJURY CAUSED BY USE OF THE PRODUCT A) IN VIOLATION OF ANY SAFETY WARNINGS OR INSTRUCTIONS;
B) NOT AUTHORIZED BY K&A MANUFACTURING, INC.; OR C) BY EVENTS BEYOND K&A MANUFACTURING, INC.’S CONTROL.
DO NOT SIT, STAND OR CRAWL ON OR UNDER THE PRODUCT.
MAKE SURE NO OBSTACLES ARE IN THE PRODUCT’S PATH.
MAKE SURE ALL CORDS ARE LONG ENOUGH TO ACCOMMODATE ANY CHANGE IN HEIGHT.
DO NOT USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURER.
2. Electrical Height Adjustment. The height of this Product may be adjusted electronically. Contact with electrical voltage may cause serious
injury and death. Only use the Product in compliance with these instructions. This Product should not be used in environments with high
levels of humidity or moisture.
KEEP CORDS AND ELECTRICAL COMPONENTS AWAY FROM HEAT AND LIQUIDS.
DO NOT OPEN ANY OF THE COMPONENTS: CONTROL BOX OR KEYPAD.
DO NOT USE WITH A DAMAGED PLUG OR CORD.
DO NOT INSERT ANYTHING INTO ANY SEAM OR OPENING.
3. Setup and Use. This Product should only be used and operated in good condition. When in use, no one should sit, stand or crawl on or
under the Product. There is a danger of crushing, shearing, injury or damage. Keep the entire range of motion of the Product clear of all
obstacles. Devices and object on the Product can tip over, fall or be crushed by the Product.
KEEP HANDS AND FINGERS CLEAR.
KEEP ALL OBSTACLES CLEAR OF THE PRODUCT’S PATH.
4. Users. This Product is not intended for use with children, individuals with restricted physical, sensory or mental capabilities, or individuals
who lack experience or knowledge, unless they are supervised by a person who is responsible for their safety or they have received
instructions from a person who is responsible for their safety concerning how the Product must be used. Children should be closely
supervised to ensure that they do not play with the Product and its height adjustment mechanism to avoid risk of physical injury or
electric shock.
KEEP CHILDREN AWAY FROM THE PRODUCT, ITS CONTROL UNITS, AND KEYPADS.
WARNING
DANGER

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 3 of 12
G. 1/4”-20 x 1/2” Flat Head Socket Cap Screw x2
H. 1/4”-20 Low Crown Acorn Nut x2
I. 5/16”-18 x 3/8” Button Socket
Cap Screw x4
J. End Cap x2
K. .75 O.D. .320 I.D. .25 Thick Black Spacer x2
L. 10 x 5/8” Round Washer Head Recex
Drive Screw x13
M. 8 x 3/4” Pan Head Phillips/Square
Drive Screw x4
N. Black Cable Clamp x4
O. X-Socket Set Screw x2
Tools Required for Assembly
A. Power Driver with Adjustable Torque
B. #2 Phillips Head Driver Bit
C. #2 Square Head Drive Bit (Recommended)
D. 3/16” Allen Wrench
E. Adjustable Wrench
F. Tape Measure
A
F
B C
Hardware and Tools Included for Assembly (may have extra)
G H I J
K L M N
Parts
P. Motor x1
Q. Hex Rod x1
R. Pull Bar x1
S. Cross Support x1
T. End Cap x2
U. Plastic Wire Management x1
V. 2-Button Switch x1
V2. Four Button Programmable Up/Down Switch x1
Optional - If you have a programmable switch,
please refer to the installation instructions
included with the switch.
W. Control Box x1
P Q R
ST
UV
D
E
V2
W
O

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 4 of 12
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
USE THIS PRODUCT ONLY AS INSTRUCTED.
FAILURE TO COMPLY WITH ALL INSTRUCTIONS AND WARNINGS
MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY.
Basic Safety Instructions
1. Intended Use. This Product is exclusively designed for use as indoor ofce furniture in compliance with all instructions and safety warnings
in the user manual. Any different use, or use extending beyond the intended use, may result in property damage or bodily injury and is pro-
hibited. This Product should not be used, operated or maintained with additional components not authorized by RightAngle Products.
BY USING THIS PRODUCT OR ANY FEATURE OF THIS PRODUCT, YOU AGREE TO COMPLY WITH ALL PRODUCT TERMS AND POL-
ICIES, INCLUDING WITHOUT LIMITATION ANY SAFETY WARNINGS AND INSTRUCTIONS, PROVIDED BY RIGHTANGLE PRODUCTS
AND ITS AFFILIATES. RIGHTANGLE PRODUCTS SHALL ASSUME NO LIABILITY FOR ANY DAMAGE OR INJURY CAUSED BY USE OF
THE PRODUCT A) IN VIOLATION OF ANY SAFETY WARNINGS OR INSTRUCTIONS; B) NOT AUTHORIZED BY RIGHTANGLE PROD-
UCTS; OR C) BY EVENTS BEYOND RIGHTANGLE PRODUCT’S CONTROL.
DO NOT SIT, STAND OR CRAWL ON OR UNDER THE PRODUCT.
MAKE SURE NO OBSTACLES ARE IN THE PRODUCT’S PATH.
MAKE SURE ALL CORDS ARE LONG ENOUGH TO ACCOMMODATE ANY CHANGE IN HEIGHT.
DO NOT USE ATTACHMENTS NOT RECOMMENDED BY THE MANUFACTURER.
2. Electrical Height Adjustment. The height of this Product may be adjusted electronically. Contact with electrical voltage may cause serious
injury and death. Only use the Product in compliance with these instructions. This Product should not be used in environments with high
levels of humidity or moisture.
KEEP CORDS AND ELECTRICAL COMPONENTS AWAY FROM HEAT AND LIQUIDS.
DO NOT OPEN ANY OF THE COMPONENTS: LEGS, CONTROL BOX, OR KEYPAD.
DO NOT USE WITH A DAMAGED PLUG OR CORD.
DO NOT INSERT ANYTHING INTO ANY SEAM OR OPENING.
3. Setup and Use. This Product should only be used and operated in good condition. When in use, no one should sit, stand or crawl on or
under the Product. There is a danger of crushing, shearing, injury or damage. Keep the entire range of motion of the Product clear of all
obstacles. Devices and object on the Product can tip over, fall or be crushed by the Product.
KEEP HANDS AND FINGERS CLEAR.
KEEP ALL OBSTACLES CLEAR OF THE PRODUCT’S PATH.
4. Users. This Product is not intended for use with children, individuals with restricted physical, sensory or mental capabilities, or individuals
who lack experience or knowledge, unless they are supervised by a person who is responsible for their safety or they have received instruc-
tions from a person who is responsible for their safety concerning how the Product must be used. Children should be closely supervised to
ensure that they do not play with the Product and its height adjustment mechanism to avoid risk of physical injury or
electric shock.
KEEP CHILDREN AWAY FROM THE PRODUCT, ITS CONTROL UNITS, AND KEYPADS.
WARNING
DANGER

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 5 of 12
Step 1
• Insert hex rod through
motor and into column.
• Open the ip mechanism
and insert two cap screws
Gthrough the outermost
holes on the inside of the
ip mechanism.
• Thread on two acorn
nuts Hand fully tighten.
Step 2
• Hex Rod and Pull Tube Installation - Simultaneously slide
hex rod and pull tube into left leg assembly. You may need to
turn the hex rod forward slightly with an adjustable wrench
to get it to align with the hex drive, see Detail B.
The following instruction illustrates a RightAngle manufactured base and worksurface. If your worksurface is
from another manufacturer, you are responsible for the base and worksurface hole alignment.
Right Leg
Detail A
A
G H
DE
Q
G
H
P
A B
DE
B
Pull Bar
Back
Left
Leg
Detail B
Both ends
Do not turn more
than 1/6th of a turn or
the worksurface will
not be level.
R

Sticker
Step 3
• Tighten set screws in ends of pull tube.
O
Step 4
I JD
C
Detail C
Double check the cross
support location. It
must be square with
both columns.
After the cross
support is leveled
and fastened,
tighten all the
screws. Insert
end caps.
K&A Manufacturing • 800.298.4351 • www.raproducts.com/install
I
J
J
Q
O
6 of 11

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 7 of 12
Step 5
• Screw to worksurface.
• Four in each ip mechanism.
• Do not tighten screws until
cross support is installed.
L
Step 6
• Tighten the screws just enough so the pull
mechanism is able to slide in and out.
A B C K L
A B C
K L
Detail D
D
Tighten all the screws
to the worksurface.
L
K

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 8 of 12
Step 7
• Install switch, control box, clips, and
plastic wire management. Note: the
control box, switch and clips can
be installed in any location, wire
lengths permitting.
A B C
L M M
M
L
L
M
M
Control Box Orientation
must be mounted this way
Control box can be relocated but
the orientation of the box must
remain the same. Long side of
control box must align with long
side of the worksurface.
Step 8
Note:
if you have
a programmable
switch (shown), please refer
to the installation instructions
included with the switch.
Optional:
Programmable
Switch
Switch
N
N
Table will NOT operate unless the
control box is screwed tight into
the table without any play.

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 9 of 12
Step 9
Cable Routing Diagram
Switch Cable
Motor Cable
Power Cable
Power Cable
Control Box
End View
Motor Cable
Switch Cable
For the safety of the user and the workstation; the control box contains an internal sensor that is
sensitive to movement, vibration, and collision. For faultless operation, ensure all cables, electronics,
and accessories are cable managed and secured. Excessive load or weight must be distributed evenly.
Failure to follow these guidelines may cause intermittent functionality.
Caution:
U
W

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 10 of 12
Save for Reference
Standard Switch
Start Up Procedure:
• Plug the power cord into a standard 110V receptacle. A power surge protector
is recommended.
• Press the down arrow until the worksurface reaches its lowest position.
• The workstation is ready for use.
• If the table is not functioning normally or has lost power, perform the reset procedure.
Reset Procedure:
• Unplug the unit from the wall for 10 seconds.
• Clear all obstructions from the travel path of the desk.
• Plug the unit back in the wall.
• Press and hold the down arrow key until the table reaches its lowest position.
Add Container Stops:
• Move the table to the upper or lower desired height.
• Rapidly press 4 times. You will hear a musical tone.
• Rapidly press 2 times. A musical tone plays two times.
- To add the upper container stop press A musical tone plays two times.
- To add the lower container stop press A musical tone plays two times.
Remove Container Stops:
• Move the table to the upper or lower preset height.
• Rapidly press 4 times. You will hear a musical tone.
• Rapidly press 2 times. A musical tone plays two times.
- To delete the upper container stop press You will hear a musical tone.
- To delete the lower container stop press You will hear a musical tone.
Troubleshooting:
If you are having any problems with the operation, contact RightAngle Products at 800.298.4351
or [e-mail]
If the leg assemblies are at uneven heights, it is usually caused by an improperly installed hex rod. Disassemble one
of the leg assemblies from the worksurface and make sure both ends of the hex rod are properly engaged in the hex
drives near the top of the leg assemblies.
Note

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 11 of 12
Start Up Procedure:
• Plug the power cord into a standard 110V receptacle. A power surge protector
is recommended.
• Press the down arrow until the worksurface reaches its lowest position.
• The workstation is ready for use.
• If the table is not functioning normally, or has lost power,
perform the reset procedure.
Reset Procedure:
• Unplug the unit from the wall for 10 seconds.
• Clear all obstructions from the travel path of the desk.
• Plug the unit back in the wall.
• Press and hold the down arrow key until the table reaches its lowest position
See Packaged Instructions for Programmable Options
Optional Programmable Switch (full instructions packaged with switch)

K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 12 of 12
If the table is unresponsive, uneven, or not functioning properly, perform a manual reset.
User settings are not reset in this process.
There are three methods to reset a workstation:
Reset Method A
1. Clear all obstructions from the travel path of the workstation
2. Disconnect the power to the control box for 30 seconds.
3. Reconnect the power
4. Press and hold the until the workstation has reached its lowest possible position.
Reset Method B (4 button programmable switch required)
1. Clear all obstructions from the travel path of the workstation
2. Quickly press UP + UP + UP + UP to enter the menu mode.
3. P01 is displayed and you will hear a musical tone.
4. Press the to navigate the menu.
5. Navigate to the P09 display
6. Press the button to enter or accept
7. Press and hold the until the workstation has reached its lowest possible position.
The workstation is now ready to operate
Reset Method C - 2 Button Switch
1. Clear all obstructions from the travel path of the workstation
2. Quickly press UP + UP + UP + UP to enter the menu mode.
3. You will hear a musical tone.
4. Press UP + UP + UP +
5. You will reach the limit adjustment menu and hear four musical tones.
6. Press and hold the until the workstation has reached its lowest possible position.
The reference is re-calibrated, the table should be leveled and the height indication should be correct.
Mechanical Reset Mode