PB TEEN Beadboard Simple Trundle User manual

1 of 3
www.pbteen.com
Beadboard Simple Trundle
Pre-assembly:
•Please read all instructions before starting to assemble.
•Two-person is recommended during assembly..
•Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or
hardware.
Parts Inclduded:
A – Long Front Siderail – 1 pc
(with decoration face)
B – Long Back Siderail – 1 pc
C – Short Siderail – 2 pcs
D – Side Bottom Board – 2 pcs
(with protruding edge)
E – Middle Bottom Board – 1 pc
(with sunken edge)
F – Wooden Bottom Board Support – 2 pcs
(with protruding edge)
Hardware Included:
G – Allen Key – 1 pc H – Hex Bolt – 8 pcs I – Barrel Nut – 8 pcs
J – Large Screw – 12 pcs K – Small Screw – 10 pcs L – Pan Head Screw – 24 pcs

2 of 3
www.pbteen.com
M – Castor – 6 pcs
Tool Required:
Phillips head screwdriver ( not included)
Instruction:
1. Slide Middle Bottom Board (E) into Side Bottom Boards (D) by fitting the protruding edge of the
Side Bottom Board (D) into the sunken edge of the Middle Bottom Board (E). Make sure the faces
with pre-drilled holes for wooden dowels on the Side Bottom Boards (D) is facing up before
assembly, as shown below. The Middle Bottom Board (E) is reversible.
2. Attach Wooden Bottom Board Supports (F) to assembled bottom boards by inserting pre-attached
wooden dowels on the Wooden Bottom Board Supports (F) into pre-drilled holes in Side Bottom
Boards (D). Insert Large Screws (J) through pre-drilled holes in the Wooden Bottom Board
Supports (F) into pre-drilled holes in the Side Bottom Boards (D) and the Middle Bottom Board
(E). Tighten Large Screws (J) with a Philips head screwdriver as shown below.
3. Attach Long Siderails (A&B) to the assembled bottom boards by inserting exposed wooden dowels
on the ends of Wooden Bottom Board Supports (F) into pre-drilled holes in the middle of Long
Siderails (A&B).
4. Attach Short Siderails (C) to Long Siderails (A&B) with Hex Bolts (H) and Barrel Nuts (I). Insert pre-
assembled wooden dowels on the end of the Long Siderails (A&B) into pre-drilled holes on the end
of Short Siderails (C). Insert Barrel Nuts (I) into holes on each end of Long Siderails (A&B). Then,
attach Short Siderails (C) to Long Siderails (A&B) with Hex Bolts (H). The Hex Bolts (H) go through
countersink holes in the end of Short Siderails (C) into the Barrel Nuts (I), as shown below. Tighten
all Hex Bolts with Allen Key (G).

3 of 3
www.pbteen.com
5. Turn the assembled unit upside down. Insert Small Screws (K) into pre-drilled countersink holes
in inner rails of the Long Siderails (A&B) and the Short Siderails (C), as shown below. Tighten all
Small Screws (K) with a Philips head screwdriver.
6. Fasten Casters (M) with Pan Head Screws (L) to the bottom of assembled unit, Using pre-drilled
holes underneath of bottom panels as guide, as shown below. Turn the unit right side up once all
Casters (M) are in place. Assembly is complete.
7. Hardware should be checked periodically for tightness.
Care Instructions:
•Avoid direct sunlight and excessive temperatures.
•Dust often using a clean, soft, dry and lint-free cloth.
•Slightly moisten cloth with water. A damp cloth holds dust and prevents scratching.
•Waxing is not recommended on lacquered finish.