PB TEEN Beadboard Media Gaming Console User manual

1/3
www.pbteen.com
Figure 1 Figure 2
Beadboard Media Gaming Console
! CAUTION
•The top shelf of this cart/stand is intended for use with Plasma/LCD/DLP/HD televisions having a
maximum screen size of 42 inches and weight of 100 lbs; or Tube televisions having a maximum screen
size of 40 inches and weight of 240 lbs.
•All other support shelves should not be loaded more than 25 lbs.
•DO NOT EXCEED RECOMMENDED LOAD. Use with products heavier than the maximum sizes and
weights indicated may result in instability causing possible injury.
•This unit contains a permanent sticker located either beneath media support shelf or inside drawer.
•Do not allow children under 16 years to move cart.
! MISE EN GARDE
•L’étagère supérieure de ce support ou chariot est destinée à recevoir une télévision à écran plasma ou
haute densité dont l’écran ne mesure pas plus de 106.68 cm et qui ne pèse pas plus de 45.4 kg; ou bien
une télévision à tube cathodique dont l’écran ne mesure pas plus de 101.6 cm et qui ne pèse pas plus de
108.86 kg.
•Les autres étagères ne doivent pas recevoir une charge de plus de 11 kg.
•NE PAS DÉPASSER LA CHARGE RECOMMANDÉE. L’utilisation avec des articles qui dépassent la taille
et le poids recommandés peut rendre l’article instable et entraîner des blessures.
•Cet article comprend un autocollant permanent, placé soit sous l’étagère supérieure, soit à l’intérieur du
tiroir.
•Il faut interdire à tout enfant de moins de 16 ans de déplacer le chariot.
04-000077-2
PRE-ASSEMBLY:
•Please read all instructions before beginning assembly.
•Two-adult assembly is recommended.
TOOLS REQUIRED (but not included):
•Phillips Head Screwdriver
ASSEMBLY:
1. To adjust the shelves unscrew the pre-assembled screw from the underside of shelf support using a
Phillips Head Screwdriver as shown below in Figure 1.
2. Determine the desired height for shelves using the corresponding peg holes located on the interior inside
of the console.
3. Insert the shelf pegs into the pre-drilled holes until fully secure. Place the shelves onto the shelf pegs,
making sure the shelf is stable. Reinsert the screws threw the shelf support and into the underside of the
shelf, tighten using a Philips Head Screwdriver as shown below in Figure 2.

2/3
www.pbteen.com
Furniture Ti
pp
in
g
Restraints
4. If left side does not touch the floor carefully grasp the left side of the console, elevate it slightly to provide
access to the levelers attached to the base of the LEFT legs. Turn the levelers in a counter clockwise
direction. Carefully return console to its upright level position.
5. If right side does not touch the floor carefully grasp the left side of the console, elevate it slightly to provide
access to the levelers attached to the base of the RIGHT legs. Turn the levelers in a counter clockwise
direction. Carefully return console to its upright level position.
6. Install two furniture tipping restraints using the enclosed instruction in the locations shown below.
CARE INSTRUCTIONS:
•Avoid direct sunlight and excessive temperatures.
•Dust often using a clean, soft, dry and lint-free cloth.
•Waxing is not recommended on lacquered finish.

3/3
www.pbteen.com
FURNITURE TIPPING RESTRAINT
WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision. Manufacturer
assumes no liability for improper installation or excessive loads placed on screws, brackets or straps.
Young children may be injured by tipping furniture and the use of a tipping restraint is highly recommended.
When properly installed, this restraint could provide protection against the unexpected tipping of furniture. We
recommend mounting this restraint to a wall stud.
Hardware included:
•(4) Brackets 48 x 21 x 10mm
•(2) Nylon Strap 300 x 12 x 8mm
•(4) Stud Mounting Screws 6 x 32mm
•(4) Product Side Mounting Screws 6 x 19mm
Note: For safe mounting it is essential to use the proper hardware for your wall type.
The included hardware is for drywall or stud mounting only. For other wall
types (ie: plaster, concrete, brick…) please consult your local hardware store.
1. Determine the final resting position of the furniture piece. Mark location
on the wall approximately 1” below the top of the back of the furniture.
Mark and drill pilot hole into the center of the stud with a 3/32” drill bit.
Attach a bracket to the stud with the long screws provided.
2. On the back of the furniture, a bracket will need to be attached to the
furniture frame at the top. To do this, temporarily move the furniture into
its final position and mark the location of the wall bracket on the
furniture frame.
3. Move the furniture away from the wall and place a bracket on the mark.
Mark and drill holes for screws with a 3/32” drill bit. Attach the bracket
to the furniture with the short screws provided.
4. Check to be sure the wall bracket is firmly screwed into wall stud and
the furniture bracket is firmly attached to the frame.
5. Move the piece of furniture into its final position so that the wall bracket
and furniture bracket are in alignment.
6. Thread the strap through brackets and tighten until snug. Do not over-
tighten.
7. Check to make sure the brackets are firmly installed and the strap is
secure.
Completed Anti-tip Kit Installation
Stud
Wallboard
Furniture Frame
Furniture Frame
Stud
Wallboard