Peco 12007HD User manual

OWNER’S MANUAL
MODEL 12006 & 12007HD
(Q0080)
THE ORIGINAL
PECO POWER SPRAYER
P PP
PECOPECOPECOPECOPECOPECO
P PP P PP P PPP
PECOPECOPECOPECOPECOPECOPECO
Revision: 4 - 6/27/2016

2
PECO POWER SPRAYER
MODEL 12006 & 12007HD
TABLE OF CONTENTS
Introduction
Thank you for purchasing the original PECO Power Sprayer. Your new PECO sprayer has been
engineered and manufactured to PECO’S high standards for safety, quality, dependability and ease
of operation. Our sprayer eliminates pumping or lugging a heavy tank on your back.
Features
— Self-contained 12-volt electric sprayer
—14” wheels and light-weight aluminum cart make
it easy to maneuver over lawn and garden surfaces
— Electric pump runs up to 5 hours on a single charge
—Removable wide-mouth five gallon container makes mixing liquids easy
—Spray adjusts from a fine mist to a 30 foot stream
SECTION PAGE
INTRODUCTION - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
FEATURES - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
DESCRIPTION- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
PARTS AND SERVICE - - - - - - - - - - - - - - - - - - - - - - - - - 4
ASSEMBLY INSTRUCTIONS - - - - - - - - - - - - - - - - - - - - - 5
OPERATION INSTRUCTIONS - - - - - - - - - - - - - - - - - - - - 6
BATTERY INFORMATION - - - - - - - - - - - - - - - - - - - - - - - 6
SECTION PAGE
SPRAYER CARE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
STORAGE - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
RETURNING PUMP/MOTOR FOR SERVICE - - - - - - - - - - 7
POWER SPRAYER PARTS LIST - - - - - - - - - - - - - - - - - - 8
EXPLODED PARTS VIEW - - - - - - - - - - - - - - - - - - - - - - - 9
SPRAYER WIRING DIAGRAM - - - - - - - - - - - - - - - - - - - - 10
SPRAYER WIRING KIT - - - - - - - - - - - - - - - - - - - - - - - - - 11
PECO LIMITED WARRANTY - - - - - - - - - - - - - - - - - - - - - 12

3
DESCRIPTION
MODEL 12006 & 12007HD
THE PECO POWER SPRAYER
HANDLE
SPRAY WAND HOSE
WAND MOUNT
BRACKET
5 GALLON
CONTAINER
POWER
ON/OFF
BATTERY
CHARGER
RECEPTACLE
SERIAL
PLATE

4
PARTS AND SERVICE INFORMATION
PECO Power Sprayer owners should record the name and telephone number of their Service Center. Your Service
Center will be happy to supply replacement parts, accessories, and do any service or repairs to your PECO Power
Sprayer. If for any reason your Service Center is unable to service your PECO Power Sprayer or supply replacement
parts, contact PECO and include the following information on the chart below.
Unit Model Number:_________________________________
Unit Engine Size: __________________________________
Unit Serial Number: _______________________________
Date of purchase: _____/_____/_________
Dealer/Distributor Name: _________________________________________
Address: ___________________________________ State:___________ Zip:____________
Phone Number: ____________________________
Address: New PECO, Inc.
10 Walden, Drive
Arden, NC 28704
Phone #: [phone] or Toll Free: [phone]
Email: [e-mail]
Model Number
Serial Number
PECO
OUTDOOR POWER EQUIPMENT
Arden, North Carolina 28704

ASSEMBLY INSTRUCTIONS
Step 1. Remove contents from shipping container.
(Power Sprayer, Handle, and Manual)
Step 2. Remove the hardware from the handle.
Insert the handle into the frame. Fasten the
handle to the frame using (2) 1/4”-20 x 1”
pan head machine screws P#(K0601) and
(2) 1/4”-20 hex nuts P#(K1124) previously removed.
.
INSERT HANDLE HERE
AND FASTEN TO THE FRAME
(2) 1/4”-20 x 1” PAN HEAD
MACHINE SCREWS P#(K0601)
AND (2) 1/4-20 HEX NUTS
P#(K1124)
5

6
OPERATION INSTRUCTIONS
After flipping the switch into the ON position, squeeze wand handle to allow air pressure in
hose to be released (make sure the strainer is completely submerged). Hold wand handle until
liquid begins to flow and all air bubbles are out of the hose. To adjust the spray into a stream,
turn the nozzle tip counter-clockwise. To adjust the spray into a fine mist, turn the nozzle tip
clockwise. Always turn the sprayer off before re-filling the container. Be sure to loosen or
remove the vent cap from the smaller tank opening to avoid creation of a vacuum inside of tank.
BATTERY & CHARGER INFORMATION
Initial Charger Setup: Using a Phillips screwdriver, loosen each screw, positive(+) &
negative(-), located on charger (Item #48, Page 10). Next, attach red positive(+) & black
negative(-) leads of charger harness (Item #49, Page 10) to corresponding red positive(+) &
black negative(-) screw on charger. Tighten screws to securely fasten leads.
Fully Charge Before First-Time Usage: Plug charger into wall socket and plug opposite
connecting end into sprayer to begin battery charging. Notice a “Green” & “Red” light located
on charger. Once correctly plugged in, a steady “Red” light designates battery charging and a
steady “Green” light designates battery charged. Leave charger connected until a steady
“Green” light is achieved before using sprayer.
The new battery charging system eliminates user error and will automatically stop charging
once detecting battery is fully charged. Battery charging time will vary depending on power
level remaining in battery. Once fully charged, the battery will last up to 5 hours before needing
to be re-charged. Only use charger provided to prevent overheating and any permanent damage
to the battery. The battery life span is around 200 charges.
SPRAYER CARE
Immediate cleaning and proper maintenance after each use will eliminate most sprayer failures.
This sprayer is made of the most chemical resistant materials available, but care must be taken
to ensure a long life. Many chemicals can deteriorate pump parts if not rinsed clean after each
use. Which solution you use will depend on the pesticides used. Always check the pesticide
label for cleaning instructions. Clean pump thoroughly with a cleaning solution for 3 minutes.
Rinse with clean soapy water for 2 minutes to remove cleaning solution. DO NOT USE BLEACH
SOLUTION OR HIGHLY FLAMMABLE LIQUIDS SUCH AS GASOLINE OR PAINT THINNER IN
SPRAYER. Soluble powders and diluted liquids may be used in the sprayer. Wet powder
solutions tend to come out of solution, coating the inside of the pump. Wet powders must be
washed out very thoroughly. Over a period of time, most chemicals will separate and a build up
in the pump. Chemicals are absorbed by plastic hoses and cannot be rinsed out after extended
periods of time. Rinse thoroughly after each use.
STORAGE
Special care should be taken before storage of the sprayer. Fully re-charge the battery.
Thoroughly rinse the pump, hoses and container with clean, soapy water.

7
RETURNING PUMP/MOTOR ASSEMBLY FOR
WARRANTY OR REPLACEMENT PURCHASE
DO NOT ATTEMPT TO DISASSEMBLE THE PUMP. Internal parts are spring
loaded and may be lost or damaged.
REMOVE THE PUMP AND MOTOR AS AN ASSEMBLY AS FOLLOWS:
1. Remove the pump lid by removing two screws shown.
2. Remove the hoses from the sprayer pump.
3. Remove the four bolts that hold pump/motor in box.
4. Disconnect the red and black wires.
5. Remove the pump/motor from the pump box.
For Warranty:
Call 1-800-438-5823 to receive a Return Authorization before sending your pump back for
service. (In N.C. call 828-684-1234)
Box your pump and motor assembly up and place the Return Authorization on the outside of the
box and return VIA United Parcel Service, (not US Mail) to the following address:
New PECO, Inc.
10 Walden Drive
Arden, NC 28704
Failure to follow the above instructions may delay the inspection/replacement of your pump
REMOVE BOLTS REMOVE BOLTS
REMOVE
REMOVE HOSES

PECO POWER SPRAYER PARTS LIST
REF NO. PART NO. DESCRIPTION QTY
01 C1173 SPRAYER MAIN FRAME BOX 01
02 C1175 SPRAYER BATTERY BOX 01
03 C1174 FRONT KICK PLATE 01
04 C0057 WAND MOUNT BRACKET 01
05 C1176 BATTERY BOX LID 01
06 B3182 SPRAYER HANDLE 01
07 B3183 AXLE LEG SUPPORTS 02
08 B0738 UPPER WAND HOSE HANGER 01
09 B0596 LOWER WAND HOSE HANGER 01
10 B4176 SPRAYER AXLE 1/2” x 16 1/4” 01
11 H4001 SPRAYER WHEEL 02
12 F4001 30 IN. HOSE 01
13 F4005 POWER SPRAYER HOSE 96 IN. 01
14 S0301 5 GALLON TANK 01
15 S0302 SPRAYER CAP LARGE 01
16 V0038 3/4” ID RUBBER GROMMET 02
17 V1022 HOSE ADAPTER 01
18 V0029 1” NEOPRENE SEAL / 5” LONG 06
19 J1301 SPRAYER WAND EXT. 18” 01
P0231 (12007HD) POLY SPRAYER WAND 18” 01
20 J1302 SPRAYER WAND EXT. 36” 01
21 J1310 WAND NOZZLE 01
P0229 (12007HD) POLY WAND NOZZLE 01
22 J1320 WAND HANDLE 01
P0230 (12007HD) POLY WAND HANDLE 01
23* J1201 SPRAYER BATTERY 01
24* J2001 TOGGLE SWITCH FOR SPRAYER 01
25* J2004 ON-OFF FACE PLATE 01
26* J2005 15/32”-32 HEX PANEL NUT 01
27 J1309 MESH STRAINER 01
29 J0129 THREADED HOSE CLAMP 04
30 K0028 TINNERMAN CLIP #14-20 04
31 K0029 TINNERMAN NUT 04
32 K0055 1/2” FLAT WASHER 04
33 K0068 TINNERMAN CLIP 02
34 K0200 1/2” PUSH NUT 02
35 K0601 PAN HEAD MACHINE SCREW 06
36 K1092 TINNERMAN SCREW 3/4” 04
37 K1096 TINNERMAN SCREW 1/2” 06
38 K1124 HEX HEAD NUT 1/4”-20 04
39 K1128 1/4”-20 NYLOC NUT 12
40 R4040 4.5” x 3” SPRAYER CARE DECAL 01
41 R1603 SERIAL NUMBER PLATE 01
42 R4027 PECO MADE IN THE U.S.A. LABEL 01
43 R4007 BATTERY CHARGE TIME LABEL 01
44 R1103 ORIGINAL POWER SPRAYER LABEL 03
46* P0210 ELECTRIC SPRAYER PUMP 01
P0228 (12007HD) FLOJET ELECTRIC SPRAYER PUMP 01
47* P0211 SPRAYER CHARGER PORT 01
48* P0212 12V SPRAYER CHARGER 01
49* P0213 SPRAYER CHARGER WIRE 72” 01
50* P0232 WIRE HARNESS (+) 01
51* P0233 WIRE HARNESS (-) 01
8
*See Page 10 & 11 for Electrical Wiring Diagram ** 12007HD Contains All Same Parts Except Where Noted

9
Power Sprayer Exploded Parts View
14
13
12
9
8
7
6
5
4
3
2
26
25
24
23 10
19
18
17
16
15
44
43
40
39
38
37
35
34
31
30
29
27
42
41
32
33
22
21
11
1
47
46
16
7
11
44
44
36

10
Sprayer Wiring Diagram
Short Post - Red Wire (+)
Medium Post - Black Wire (-)
Long Post - Not Used
Red Pump Wire (+) to
On/Off Switch Top
Terminal
Black Pump Wire (-) to
P0233 Harness
(50)
P0232 Harness
(51)
P0233 Harness
(46)
(49)
(48)
Ref. # Part # Description Qty
23 J1201 SPRAYER BATTERY 01
24 J2001 TOGGLE SWITCH FOR SPRAYER 01
25 J2004 ON-OFF FACE PLATE 01
26 J2005 15/32”-32 HEX PANEL NUT 01
46 P0210 ELECTRIC SPRAYER PUMP 01
P0228 (12007HD) FLOWJET ELECTRIC SPRAYER PUMP 01
47 P0211 SPRAYER CHARGER PORT 01
48 P0212 12V CHARGER 01
49 P0213 CHARGER HARNESS (72” Long) 01
50 P0232 WIRE HARNESS (+) 01
51 P0233 WIRE HARNESS (-) 01
(24)(25)(26)
(47)
(23)