Peco PS5 User manual

OPERATOR’S MANUAL
MANUAL PART#: Q0582 Initial Release - Sept 2021
ASSEMBLY OPERATION MAINTENANCE
P
PP
PECO
PECOPECO
PECO
PECOPECO
P
PP
P
PP
P
P
PECO
PECO
RRR
PS5 Power Sprayer
THE ORIGINAL
POWER SPRAYER
Model# 12008

2
PECO POWER SPRAYER
TABLE OF CONTENTS
SECTION PAGE
Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
I INTRODUCTION AND DESCRIPTION - - - - - - - - - - - - 4
Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Description - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
II INSTALLATION FOR USE - - - - - - - - - - - - - - - - - - - - - 5
Sprayer Pump Installation - - - - - - - - - - - - - - - - - - 5
Battery Installation - - - - - - - - - - - - - - - - - - - - - - - 5
Component Back Installation - - - - - - - - - - - - - - - - 6
Component Top Installation - - - - - - - - - - - - - - - - - 7
Right & Left Chassis Installation - - - - - - - - - - - - - - 7
Power Sprayer Handle Assy Installation - - - - - - - - - 8
Power Sprayer Handle Assy Adjustment - - - - - - - - 9
Power Sprayer Wheel Installation - - - - - - - - - - - - - 9
SECTION PAGE
29” Stainless Steel Sprayer Wand Installation - - - - - 10
Sprayer Wire Harness - - - - - - - - - - - - - - - - - - - - 11
Exploded Views & Parts List - - - - - - - - - - - - - - 12-14
Overall Parts List - - - - - - - - - - - - - - - - - - - - - - - - 15
Safety Decals - - - - - - - - - - - - - - - - - - - - - - - - - - 16
III OPERATING INSTRUCTIONS - - - - - - - - - - - - - - - - - - 17
General Safety - - - - - - - - - - - - - - - - - - - - - - - - - 17
Battery & Charging Information - - - - - - - - - - - - - - - 17
Sprayer Care - - - - - - - - - - - - - - - - - - - - - - - - - - 17
Storage - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
V PARTS AND SERVICE - - - - - - - - - - - - - - - - - - - - - - - 17
Parts And Service Information - - - - - - - - - - - - - - - 17
Viton’s Chemical Compatibility - - - - - - - - - - - - - 18-20
Additional Option - - - - - - - - - - - - - - - - - - - - - - - - 21
SAFETY
2021 (v1.0)
1. Read the operator’s manual carefully and familiarize yourself with the proper use of your sprayer
2. Know the controls and how to use them properly. READ THE OPERATOR’S MANUAL!
3. Always inspect your sprayer thoroughly before and after each use. Check to be sure hose is securely attached and
in good condition before use.
4. Use special care when spraying near electrical installations.
5. Keep the work area clear of people and animals.
6. Never use the sprayer during windy conditions.
7. Wear protective gear and clothing when filling, using and cleaning the sprayer.
8. Always release pressure in the pump prior to filling, cleaning or servicing the sprayer.
9. Before opening a container of the spray material carefully read, understand and follow all instructions provided by
the spray material's manufacturer
10. Do not eat, drink or smoke while spraying.
11. Thoroughly wash face and hands with soap and water after spraying.
12. Do not transfer spray materials to other containers, especially food and/or drink containers.
13. Keep spray materials locked up and out of reach of children and animals.
14. Use only original manufacture's replacement parts.

3
New PECO, Inc. extends the following warranties to the ORIGINAL PURCHASER of each New PECO, Inc. consumer product
purchased from one of our Dealers or directly from New PECO, Inc., subject to the following limitations:
A. ITEMS COVERED UNDER WARRANTY:
1. PRODUCT WARRANTY – Any part or parts which are deemed defective in material or workmanship, as delivered to the
original purchaser, will either be repaired or replaced, as New PECO, Inc. elects, without charge for parts or labor, if
the defect appears within 12 months from the date of purchase of the product to the Original Purchaser.
2. PARTS REPLACED DURING WARRANTY – Any New PECO, Inc. part which is furnished in performance of this warranty
and is defective in material or workmanship as delivered to the purchaser will be repaired or replaced, as New PECO,
Inc. elects, before the expiration of the original warranty period.
B. WARRANTY DISTINCTIONS:
1. RESIDENTIAL - Products put to a personal use around a single household or residence are considered Residential.
Products designated as “Residential” are warrantied for 12 months from the date of purchase of the product, to the
ORIGINAL PURCHASER with proof of purchase, when used for or in residential applications.
2. COMMERCIAL – Products put to any business use (agricultural, commercial or industrial) or used at multiple locations
are considered Commercial. Products designated as “Commercial” are warrantied for 12 months from the date of
purchase of the product, to the ORIGINAL PURCHASER with proof of purchase, when used for or in commercial
applications. Products designated as “Residential” are warrantied for 90 days from the date of purchase of the
product, to the ORIGINAL PURCHASER with proof of purchase, when used for or in Commercial applications.
3. RENTAL – Products used for Rental or Lease Purposes are warrantied for 45 days from date of purchase of the product,
to the ORIGINAL PURCHASER with proof of purchase, when used for or in a rental business.
C. ITEMS NOT COVERED BY NEW PECO WARRANTY:
1. ENGINES & BATTERIES: Engines and Batteries attached to New PECO, Inc. products are covered under their respective
separate manufacturer warranties and those companies must be contacted directly to file a warranty claim. Briggs &
Stratton: https://www.briggsandstratton.com/na/en_us/support/warranty.html
2. UNAPPROVED ALTERATION OR MODIFICATION: All obligations of New PECO, Inc. under this warranty shall be
terminated if products are altered or modified in any way not approved by New PECO, Inc.
3. ACCIDENTS & NORMAL MAINTENANCE: This warranty covers ONLY manufacturers defective material and
workmanship. It does not cover depreciation or damage caused by normal wear & tear, accident, improper
maintenance, misuse or abuse of products. New PECO, Inc. products must be operated and maintained in
accordance with the instructions furnished in the manuals. The cost of normal maintenance and normal replacement
of service items such as belts, cutting blades, hoses, bags, etc., which are not defective shall be paid for by the
purchaser.
4. NO SERVICE CENTER WARRANTY: The selling Service Center/Dealer makes no warranty on his own on any item
warranted by New PECO, Inc. unless he delivers to purchaser a separate written warranty certificate specifically
warranting the item. The Service Center or Dealer has no authority to make any representation or promise on behalf
of New PECO, Inc. or to modify the terms of the original warranty in any way.
5. NO REPRESENTATIONS ADDITONAL WARRANTIES, DISCLAIMER: Neither New PECO, Inc. nor any company affiliated
with New PECO, Inc. makes any warranties, representations or promises as to the quality of performance of its
products other than those set forth herein. Except as described above, New PECO, Inc. makes no other warranties
AND SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES OF FITNESS AND MERCHANTABILITY.
6. REMEDIED EXCLUSIVE: The only remedies the purchaser has in connection with the breach or performance of any
warranty on New PECO, Inc. consumer products are set forth above. In no event will New PECO, Inc. be liable for
special incidental or consequential damages.
Warranty service is available through your local authorized service dealer or distributor. If you do not know the dealer or
distributor in your area, search by your zip code on www.lawnvac.com or contact our Sales Department at New PECO, Inc.
800-438-5823 or email [email protected]m.
PECO LIMITED WARRANTY FOR NEW PRODUCTS
2020 (v1.0)

4
Introduction
Thank you for purchasing the PECO Power Sprayer.
Your new PECO Sprayer has been engineered and
manufactured to PECO’s high standards for safety,
quality, dependability and ease of operation.
No need for pumping or lugging with the all new PS5
Power Sprayer. It’s completely self-contained and rolls
easily over lawns and through gardens. The spray wand
is always right at hand with multiple spray patterns to fit
the job. Spray from flat or a fine mist adjustable to a 40’
stream. A full charge on the battery can last for 6 hours,
and the wide-mouthed illuminated container can hold up
to five gallons. The sprayer handle folds for easy
transport & storage.
Description
Self-contained 12-volt Electric Sprayer
14” Wheels and Lightweight Aluminum Cart with Folding
Handle for easy Transport & Storage
40psi Electric Pump runs up to 6 hours on a single
charge
Viton Valves / Santoprene Diaphragm
Illuminated Wide-Mouth 5-Gallon Container
Standard Adjustable Nozzle Spray adjusts from a fine
mist to a 40 foot Solid Stream
TeeJet Nozzle for Uniform Coverage throughout the Flat
Spray pattern also included
29” Stainless Steel Spray Wand
Commercial Shut-Off Valve with Lock On / Off Features
10’ Hose with a Quick-Release Hose Hanger
SECTION 1 - INTRODUCTION & DESCRIPTION

5
Sprayer Pump Installation
Align and position the Sprayer Pump (Item #2) to the (4) mount holes on the Chassis Body (Item #1) as shown in
Figure A. Secure the Sprayer Pump by using (4) #10-12 Flat Tinnerman Nuts (Item #3) and (4) #10-12 x 3/4” Blunt Tip
Sheet Metal Screws (Item #4). Refer to Figure A.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure A
Battery Installation
Position the Power Sprayer Battery (Item #1) vertically, as shown in Figure A, to the right side of the Sprayer’s
Chassis Body (Item #2). Secure the Power Sprayer Battery by using (1) Battery Clamp (Item #3), (1) 1/4”-20 x 4-1/2”
Carriage Bolt (Item #4), (1) Heavy Washer (Item #5) and (1) 1/4-20” Wing Nut (Item #6). Refer to figure B.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure B
Section II - INSTALLATION FOR USE

6
Component Back Installation
Once your Sprayer Pump & Power Sprayer Battery has been installed, install the aluminum Component Back (Item
#2) to the Chassis Body (Item #1).
First, locate all bolt holes on the edge of both parts and install (12) Small Tinnerman Clips (Item #4). See Figure A.
Next, align the Component Back to the Chassis Body by aligning the (2) bottom bolt holes to those on the Chassis
Body and securing the Component Back by using (2) #10-12 x 1/2” Tinnerman Screws (Item #5). See Figure A.
Finally, install (3) Grommets into the 1-1/8” Dia Holes located on the Front and Left side of the Chassis Body. See
Figure B.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure A
Figure B

7
Component Top Installation
With the pre-installed Tinnerman Clip (Item #4) onto the Chassis Body (Item #1) and the Component Back (Item #2),
install the Aluminum Component Top (Item #3) by aligning the Top over the Chassis Body and the Component Back
by securing the Top by using (4) #10-12 x 1/2” Tinnerman Screws (Item #5). Refer to the Figure below.
Note: Some parts and part features have been hidden from view for visual clarity.
Right & Left Chassis Installation
To install the Right Chassis (Item #1), first install (5) Small Tinnerman Clips (Item #4) to the Right side of the Chassis
Body. Then Align the Right Chassis’ bolt holes with the Tinnerman Clips and secure the Right Chassis by using (7)
#10-12 x 1/2” Tinnerman Screws (Item #3). See Figure B.
To install the Left Chassis (Item #2), first install (5) Small Tinnerman Clips (Item #4) to the Left side of the Chassis
Body. Then Align the Left Chassis’ bolt holes with the Tinnerman Clips and secure the Left Chassis by using (9) #10-
12 x 1/2” Tinnerman Screws (Item #3). See Figure C.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure B
Figure C
Figure A
Installed Component Top

8
Power Sprayer Handle Assembly Installation
Before installing the Power Sprayer Handle Assembly (Item #1), install (2) Locator Pin Nuts (Item #3) to either side of
the Chassis by using (2) 1/4”-20 x 1/2” HHCS (Item #4). See Figure A.
Once the Locator Pin Nuts have been installed, position the Chassis Brace (Item #2) between the Left & Right
Chassis as seen in Figure B. Align the Chassis Brace’s bolt holes to those on the Left & Right Chassis keeping it
positioned in place by using (2) 5/16”-18 x 1-1/4” Carraige Bolts (Item #6).
When the Chassis Brace is in place, place (2) 5/16” Flat Washers (Item #5) over the Carriage Bolt on the outside of
the Chassis. Then Position the Power Sprayer Handle Assembly (Item #1) over Flat Washer and Carriage Bolt.
Secure the Power Sprayer Handle Assembly by using (2) Wing Knobs (Item #7). Refer to Figure B below.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure A Figure B

9
Power Sprayer Handle Assembly Adjustment
The Power Sprayer Handle Assembly P#(A2377) position can be adjusted to lower or raise the Handle by moving the
(2) Locator Pin Nuts P#(B4251) to the different set of holes. See Figure A below.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure B
Sprayer Wheel Installation
Before installing the Sprayer Wheels (Item #1), install the Axle (Item #2) by passing it through the through hole of
both the Left & Right Chassis. Refer to Figure A.
Next, place a Spacer Bushing (Item #3) on either side of the Axle outside of the Left & Right Chassis.
Once, the Spacer Bushing is in place, slide the Sprayer Wheel over the Axle and secure the Sprayer Wheel by using
(1) 5/8” Push Nuts (Item #4) PER side. Refer to Figure A below.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure A
Handle Assembly
to Locator Pin
Locator Pin
Adjustment Holes

10
J1204B Flat Nozzle (Standard) J1205 Elbow Nozzle (Secondary)
29” Stainless Steel Sprayer Wand Assembly
Your Stainless Steel Sprayer Wand Assembly will come installed with a standard Flat Nozzle (Item #2), there will be a
secondary Elbow Nozzle P#(J1205) available as shown in Figure B.
When switching out your Sprayer Nozzle, you can store whichever one you’re not using onto the Chassis Brace as
shown in Figure C.
Sprayer Nozzle Types
Figure A
Figure B
Figure C

11
Figure B
Sprayer Wire Harness
12”
4”
4” 4”
1/2” 2”
5”
Note: The Wiring Diagram is not drawn to scale or scaled correctly,
the dimensions are intended to be used as a reference

12
12008 Power Sprayer Exploded Parts View

13
12008 Power Sprayer Exploded Parts List

14
A2377 Power Sprayer / Handle Assembly
Exploded Parts View

15

16
SAFETY DECALS
To promote safe operation, New PECO, Inc. supplies safety decals on all products manufactured. Damage can occur to safety
decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals.
(1) R4040
Label / Sprayer Care
(2) R0054
Decal / PS5 Logo
(2) R1103
Decal / PS5 Power Sprayer
(1) R1106
Decal / PECO Logo
(1) R0056
Decal / Designed &
Built in the USA

17
OPERATING INSTRUCTIONS III
1. After flipping the switch into the ON position, squeeze
wand handle to allow air pressure in hose to be
released (make sure the strainer is completely
submerged).
2. Hold wand handle until liquid begins to flow and all air
bubbles are out of the hose.
3. Always turn the sprayer off before re-filling the
container.
Be sure to loosen or remove the vent cap from the
smaller tank opening to avoid creation of a vacuum
inside of tank.
A unit that has been used with herbicides should never
be used to spray insecticides, unless the sprayer has
been properly cleaned and all other chemicals
neutralized. Failure to do this could cause you to kill
plants that have been sprayed. Consult with the
manufacturer of the chemicals in sue to obtain proper
instructions.
BATTERY & CHARGER INFORMATION
Fully Charge Before First-Time Usage:
* Plug Charger into wall socket and plug opposite
connecting end into Sprayer to begin battery charging.
* Notice a “Green” & “Red” light located on Charger.
* Once correctly plugged in, a steady “Red” light
designates battery charging and a steady “Green” light
designates battery charged.
* Leave charger connected until a steady “Green” light is
achieved before using sprayer.
The new battery charging system eliminates user error
and will automatically stop charging once a full charge is
detected. Battery charging time will vary depending on
power level remaining in battery. The battery will last up
to 5 hours in between full charges. Only use charger
provided to prevent overheating and permanent damage
to the battery.
The battery life span is approximately 200 charges.
2021 (v1.0)
SPRAYER CARE
A. This sprayer is made of the most chemical resistant
materials available, but care must be taken to ensure
product longevity. Immediate cleaning and proper
maintenance after each use will eliminate most
sprayer failures.
B. Many chemicals can deteriorate pump parts if not
rinsed clean after each use. Which solution you use
will depend on the pesticides used. Always check the
pesticide label for cleaning instructions.
C. Clean pump thoroughly with a cleaning solution for 3
minutes. Rinse with clean soapy water for 2 minutes
to remove cleaning solution.
* DO NOT USE BLEACH SOLUTION OR HIGHLY
FLAMMABLE LIQUIDS SUCH AS GASOLINE
OR PAINT THINNER IN SPRAYER.
D. Soluble powders and diluted liquids may be used in
the sprayer. Wet powder solutions tend to come out
of solution, coating the inside of the pump. Wet
powders must be washed out very thoroughly. Over a
period of time, most chemicals will separate and
cause a build up in the pump. Chemicals are
absorbed by the plastic hoses and cannot be rinsed
out after extended periods of time.
E. Rinse thoroughly after each use.
STORAGE
Special care should be taken before storage of the
sprayer. Fully re-charge the battery. Thoroughly rinse
the pump, hoses and container with clean, soapy water.
Do NOT store sprayer with the pump pressurized or with
spray solution in the tank.
PARTS AND SERVICE
INFORMATION IV
PECO Power Sprayer owners should record the name
and telephone number of their Service Center. Your
Service Center will be happy to supply replacement
parts, accessories, and do any service or repairs to your
PECO Power Sprayer. If for any reason your Service
Center is unable to service your PECO Power Sprayer
or supply replacement parts, contact PECO and include
the following information on the chart below.
DOCUMENT THE FOLLOWING INFORMATION FOR FUTURE REFERENCE
Unit Model Number:_______________________________________________
Unit Serial Number:________________________________________________
Date of purchase:________/________/_________
Dealer/Distributor Name:__________________________________________
Address: _________________________________ State:_______ Zip:_______
Phone Number: ____________________________________________________

18
Viton Chemical Compatibility
Your Power Sprayer comes equipped with Viton Valves. Viton is a synthetic rubber that resists many hydrocarbons,
biodiesel and petro chemicals, but it is NOT compatible with ketones. DO NOT use substances such as acetone,
esters, amines, organic acids, acetic acid, methyl ethyl ketone (MEK), ethyl acetate, etc. Use the chart below as
reference to determine which chemical maybe compatible with your Power Sprayer.
Note: The information in the chart below is intended to be used ONLY as a guide in selecting appropriate chemical
compatibility for your Power Sprayer with Viton Valves. Ratings of chemical behavior listed in the chart below were
tested at a 48-hr exposure period to Viton. Effects for exposures beyond this 48-hr period is unknown. We do not
warrant nor imply that the information in the chart below is accurate or complete.
Footnotes
1 Satisfactory to 72°F (22°C)
2 Satisfactory to 120°F (48°C)
Ratings: Chemical Effect
A = Excellent
B = Good, Minor Effect, Slight Corrosion or Discoloration
C = Fair, Moderate Effect, NOT Recommended for Continuous Use.
Softens, Loss of Strength, or Swelling may occur
D = Severe Effect, NOT Recommended for ANY Use
N/A = Information Not Available
Chemical Com patability Che mical Com patability Che mical Com patability
Carbon Disulfide A1-Excellent Manganese Sulfate A2-Excellent Ammonium Phosphate, Monobasic A-Excellent
Ethyl Benzoate A1-Excellent Nickel Nitrate A2-Excellent Ammonium Phosphate, Tribasic A-Excellent
Isooctane A1-Excellent Petroleum A2-Excellent Ammonium Sulfate A-Excellent
Lithium Chloride A1-Excellent Potassium Sulfate A2-Excellent Amyl Alcohol A-Excellent
Mercuric Cyanide A1-Excellent Salt Brine (NaCl saturated) A2-Excellent Aniline A-Excellent
Mercurous Nitrate A1-Excellent Sodium Cyanide A2-Excellent Aniline Hydrochloride A-Excellent
Methyl Chloride A1-Excellent Sodium Sulfide A2-Excellent Antifreeze A-Excellent
Methyl Dichloride A1-Excellent Sodium Sulfite A2-Excellent Arochlor 1248 A-Excellent
Palmitic Acid A1-Excellent Sulfuric Acid (10-75%) A2-Excellent Aromatic Hydrocarbons A-Excellent
Phosphorus Trichloride A1-Excellent Sulfuric Acid (hot concentrated) A2-Excellent Arsenic Salts A-Excellent
Phthalic Acid A1-Excellent Tricresylphosphate A2-Excellent Asphalt A-Excellent
Propylene A1-Excellent Acetyl Chloride (dry) A-Excellent Barium Carbonate A-Excellent
Resorcinal A1-Excellent Acetylene A-Excellent Barium Chloride A-Excellent
Salicylic Acid A1-Excellent Alcohols: Amyl A-Excellent Barium Cyanide A-Excellent
Sodium Benzoate A1-Excellent Alcohols: Benzyl A-Excellent Barium Hydroxide A-Excellent
Sodium Bromide A1-Excellent Alcohols: Butyl A-Excellent Barium Nitrate A-Excellent
Sodium Hypochlorite (<20%) A1-Excellent Alcohols: Ethyl A-Excellent Barium Sulfate A-Excellent
Sodium Hypochlorite (100%) A1-Excellent Alcohols: Isobutyl A-Excellent Barium Sulfide A-Excellent
Stearic Acid A1-Excellent Alcohols: Isopropyl A-Excellent Beet Sugar Liquids A-Excellent
Sulfate (Liquors) A1-Excellent Alcohols: Propyl A-Excellent Benzene A-Excellent
Sulfuric Acid (75-100%) A1-Excellent Aluminum Chloride A-Excellent Benzene Sulfonic Acid A-Excellent
Vinyl Acetate A1-Excellent Aluminum Chloride 20% A-Excellent Benzoic Acid A-Excellent
Vinyl Chloride A1-Excellent Aluminum Fluoride A-Excellent Benzol A-Excellent
Water, Deionized A1-Excellent Aluminum Hydroxide A-Excellent Bleaching Liquors A-Excellent
Adipic Acid A2-Excellent Aluminum Potassium Sulfate 10% A-Excellent Borax (Sodium Borate) A-Excellent
Aluminum Nitrate A2-Excellent Aluminum Potassium Sulfate 100% A-Excellent Boric Acid A-Excellent
Antimony Trichloride A2-Excellent Aluminum Sulfate A-Excellent Brew ery Slop A-Excellent
Benzyl Chloride A2-Excellent Alums A-Excellent Bromine A-Excellent
Calcium Nitrate A2-Excellent Ammonium Acetate A-Excellent Butane A-Excellent
Carbon Tetrachloride (dry) A2-Excellent Ammonium Bifluoride A-Excellent Butanol (Butyl Alcohol) A-Excellent
Cupric Acid A2-Excellent Ammonium Carbonate A-Excellent Butylene A-Excellent
Diethylene Glycol A2-Excellent Ammonium Chloride A-Excellent Calcium Bisulfide A-Excellent
Diphenyl A2-Excellent Ammonium Nitrate A-Excellent Calcium Bisulfite A-Excellent
Lead Nitrate A2-Excellent Ammonium Persulfate A-Excellent Calcium Carbonate A-Excellent
Magnesium Chloride A2-Excellent Ammonium Phosphate, Dibasic A-Excellent Calcium Chlorate A-Excellent

19
Chemical Com patability Chemical Com patability Chemical Com patability
Calcium Chloride A-Excellent Glucose A-Excellent Perchloric Acid A-Excellent
Calcium Hydroxide A-Excellent Glycerin A-Excellent Perchloroethylene A-Excellent
Calcium Hypochlorite A-Excellent Glycolic Acid A-Excellent Petrolatum A-Excellent
Calcium Sulf ate A-Excellent Gold Monocyanide A-Excellent Phenol (10%) A-Excellent
Calgon A-Excellent Heptane A-Excellent Phenol (Carbolic Acid) A-Excellent
Carbolic Acid (Phenol) A-Excellent Hexane A-Excellent Phosphoric Acid (>40%) A-Excellent
Carbon Bisulfide A-Excellent Hydrobromic Acid 100% A-Excellent Phosphoric Acid (crude) A-Excellent
Carbon Monoxide A-Excellent Hydrobromic Acid 20% A-Excellent Phosphoric Acid (S40%) A-Excellent
Carbon Tetrachloride A-Excellent Hydrochloric Acid 100% A-Excellent Photographic Developer A-Excellent
Carbonated Water A-Excellent Hydrochloric Acid 20% A-Excellent Phthalic Anhydride A-Excellent
Carbonic Acid A-Excellent Hydrochloric Acid 37% A-Excellent Picric Acid A-Excellent
Chlorinated Glue A-Excellent Hydrocyanic Acid A-Excellent Potash (Potassium Carbonate) A-Excellent
Chlorine (dry) A-Excellent Hydrocyanic Acid (Gas 10%) A-Excellent Potassium Bicarbonate A-Excellent
Chlorine Water A-Excellent Hydrofluoric Acid 20% A-Excellent Potassium Bromide A-Excellent
Chlorine, Anhydrous Liquid A-Excellent Hydrofluosilicic Acid 100% A-Excellent Potassium Chlorate A-Excellent
Chlorobenzene (Mono) A-Excellent Hydrofluosilicic Acid 20% A-Excellent Potassium Chloride A-Excellent
Chlorobromomethane A-Excellent Hydrogen Gas A-Excellent Potassium Chromate A-Excellent
Chocolate Syrup A-Excellent Hydrogen Peroxide 10% A-Excellent Potassium Cyanide Solutions A-Excellent
Chromic Acid 30% A-Excellent Hydrogen Peroxide 100% A-Excellent Potassium Dichromate A-Excellent
Chromic Acid 5% A-Excellent Hydrogen Peroxide 30% A-Excellent Potassium Ferricyanide A-Excellent
Chromic Acid 50% A-Excellent Hydrogen Peroxide 50% A-Excellent Potassium Ferrocyanide A-Excellent
Citric Acid A-Excellent Hydroxyacetic Acid 70% A-Excellent Potassium Iodide A-Excellent
Citric Oils A-Excellent Iodine A-Excellent Potassium Nitrate A-Excellent
Cloroxr (Bleach) A-Excellent Isotane A-Excellent Potassium Permanganate A-Excellent
Copper Chloride A-Excellent Lead Sulfamate A-Excellent Potassium Sulfide A-Excellent
Copper Cyanide A-Excellent Ligroin A-Excellent Propylene Glycol A-Excellent
Copper Fluoborate A-Excellent Lubricants A-Excellent Pyrogallic Acid A-Excellent
Copper Nitrate A-Excellent Magnesium Carbonate A-Excellent Rosins A-Excellent
Copper Sulfate 5% A-Excellent Magnesium Hydroxide A-Excellent Rust Inhibitors A-Excellent
Copper Sulfate>5% A-Excellent Magnesium Nitrate A-Excellent Sea Water A-Excellent
Cresols A-Excellent Magnesium Sulfate (Epsom Salts) A-Excellent Shellac (Bleached) A-Excellent
Cresylic Acid A-Excellent Maleic Acid A-Excellent Shellac (Orange) A-Excellent
Cyanic Acid A-Excellent Maleic Anhydride A-Excellent Silicone A-Excellent
Cyclohexane A-Excellent Malic Acid A-Excellent Silver Nitrate A-Excellent
Detergents A-Excellent Melamine A-Excellent Soap Solutions A-Excellent
Diethylamine A-Excellent Mercuric Chloride (dilute) A-Excellent Sodium Aluminate A-Excellent
Diphenyl Oxide A-Excellent Methane A-Excellent Sodium Bicarbonate A-Excellent
Dyes A-Excellent Methyl Bromide A-Excellent Sodium Bisulfate A-Excellent
Epsom Salts (Magnesium Sulfate) A-Excellent Mineral Spirits A-Excellent Sodium Bisulfite A-Excellent
Ethane A-Excellent Naphtha A-Excellent Sodium Borate (Borax) A-Excellent
Ethanol A-Excellent Naphthalene A-Excellent Sodium Carbonate A-Excellent
Ethyl Chloride A-Excellent Natural Gas A-Excellent Sodium Chlorate A-Excellent
Ethyl Sulfate A-Excellent Nickel Chloride A-Excellent Sodium Chloride A-Excellent
Ethylene Bromide A-Excellent Nickel Sulfate A-Excellent Sodium Chromate A-Excellent
Ethylene Chlorohydrin A-Excellent Nitric Acid (20%) A-Excellent Sodium Ferrocyanide A-Excellent
Ethylene Dichloride A-Excellent Nitric Acid (50%) A-Excellent Sodium Fluoride A-Excellent
Ethylene Glycol A-Excellent Nitric Acid (5-10%) A-Excellent Sodium Hydrosulfite A-Excellent
Ferric Chloride A-Excellent Nitric Acid (Concentrated) A-Excellent Sodium Metaphosphate A-Excellent
Ferric Nitrate A-Excellent Oleum 100% A-Excellent Sodium Metasilicate A-Excellent
Ferric Sulfate A-Excellent Oleum 25% A-Excellent Sodium Nitrate A-Excellent
Ferrous Chloride A-Excellent Oxalic Acid (cold) A-Excellent Sodium Perborate A-Excellent
Formaldehyde 40% A-Excellent Ozone A-Excellent Sodium Peroxide A-Excellent
Gallic Acid A-Excellent Pentane A-Excellent Sodium Polyphosphate A-Excellent

20
Chem ical Com patability Chem ical Com patability Chem ical Compatability
Sodium Silicate A-Excellent Nitrobenzene B-Good Lacquer Thinners D-Severe Effect
Sodium Sulfate A-Excellent Nitrous Acid B-Good Lacquers D-Severe Effect
Sodium Tetraborate A-Excellent Nitrous Oxide B-Good Lead Acetate D-Severe Effect
Sodium Thiosulfate (hypo) A-Excellent Paraffin B-Good Methyl Acetate D-Severe Ef fect
Stannic Chloride A-Excellent
Potassium Hydroxide (Caustic Potash)
B-Good Methyl Acetone D-Severe Effect
Stannic Fluoborate A-Excellent Styrene B-Good Methyl Acrylate D-Severe Eff ect
Stannous Chloride A-Excellent Sulfuric Acid (cold concentrated) B-Good Methyl Butyl Ketone D-Severe Effect
Sulfur Chloride A-Excellent Xylene B-Good Methyl Cellosolve D-Severe Ef fect
Sulfur Dioxide A-Excellent Butyl Phthalate C1-Fair Methyl Ethyl Ketone D-Severe Effect
Sulfur Dioxide (dry) A-Excellent Alcohols: Hexyl C-Fair Methyl Ethyl Ketone Peroxide D-Severe Eff ect
Sulfur Trioxide A-Excellent Alcohols: Methyl C-Fair Methyl Isobutyl Ketone D-Severe Effect
Sulfur Trioxide (dry) A-Excellent Dichlorobenzene C-Fair Methyl Isopropyl Ketone D-Severe Effect
Sulfuric Acid (<10%) A-Excellent Dichloroethane C-Fair Methyl Methacrylate D-Severe Ef fect
Sulfurous Acid A-Excellent Dimethyl Formamide C-Fair Methylamine D-Severe Ef fect
Tannic Acid A-Excellent Ether C-Fair Monoethanolamine D-Severe Effect
Tartaric Acid A-Excellent Fluorine C-Fair Mustard D-Severe Effect
Tetrachloroethane A-Excellent Formic Acid C-Fair Nitromethane D-Severe Effect
Tetrachloroethylene A-Excellent Magnesium Oxide C-Fair Pyridine D-Severe Effect
Trichloroethane A-Excellent Methanol (Methyl Alcohol) C-Fair Sodium Acetate D-Severe Effect
Trichloroethylene A-Excellent Methyl Alcohol 10% C-Fair Sodium Hydroxide (50%) D-Severe Eff ect
Trichloropropane A-Excellent Monochloroacetic acid C-Fair Sodium Hydroxide (80%) D-Severe Effect
Trisodium Phosphate A-Excellent Sodium Hydroxide (20%) C-Fair Tetrahydrofuran D-Severe Effect
Turpentine A-Excellent Toluene (Toluol) C-Fair Triethylamine D-Severe Effect
Urea A-Excellent Trichloroacetic Acid C-Fair Acetyl Bromide N/A
Varnish A-Excellent Acetaldehyde D-Severe Eff ect Ammonium Caseinate N/A
Water, Acid, Mine A-Excellent Acetate Solvent D-Severe Effect Ammonium Oxalate N/A
Water, Distilled A-Excellent Acetic Acid, Glacial D-Severe Ef fect Ammonium Thiosulf ate N/A
Water, Fresh A-Excellent Acetic Anhydride D-Severe Effect Benzonitrile N/A
Water, Salt A-Excellent Acetone D-Severe Effect Calcium Bisulfate N/A
Weed Killers A-Excellent Acrylonitrile D-Severe Effect Carbon Tetrachloride (w et) N/A
Zinc Chloride A-Excellent Alcohols: Diacetone D-Severe Effect Chloric Acid N/A
Zinc Sulfate A-Excellent Amines D-Severe Effect Chromium Salts N/A
Amyl Chloride B1-Good Ammonia 10% D-Severe Effect Hydrochloric Acid, Dry Gas N/A
Butyric Acid B1-Good Ammonia Nitrate D-Severe Ef fect Iodine (in alcohol) N/A
Fluosilicic Acid B1-Good Ammonia, anhydrous D-Severe Effect Iodoform N/A
Linoleic Acid B1-Good Ammonia, liquid D-Severe Effect Lithium Hydroxide N/A
Lye: Ca(OH)2 Calcium Hydroxide B1-Good Ammonium Sulfite D-Severe Effect Magnesium Bisulf ate N/A
Lye: NaOH Sodium Hydroxide B1-Good Amyl Acetate D-Severe Effect Morpholine N/A
Acetamide B-Good Benzaldehyde D-Severe Effect Nitrating Acid (<15% HNO3) N/A
Acetic Acid B-Good Butyl Amine D-Severe Effect Nitrating Acid (>15% H2SO4) N/A
Acetic Acid 20% B-Good Butyl Ether D-Severe Effect Nitrating Acid (S1% Acid) N/A
Acetic Acid 80% B-Good Butylacetate D-Severe Effect Nitrating Acid (S15% H2SO4) N/A
Alcohols: Octyl B-Good Chloroacetic Acid D-Severe Ef fect Nitrogen Fertilizer N/A
Ammonium Hydroxide B-Good Chlorosulfonic Acid D-Severe Effect Phosphoric Acid (molten) N/A
Aqua Regia (80% HCl, 20% HNO3) B-Good Cyclohexanone D-Severe Effect Phosphoric Acid Anhydride N/A
Butadiene B-Good Diacetone Alcohol D-Severe Effect Phosphorus N/A
Calcium Oxide B-Good Diethyl Ether D-Severe Effect Potassium Hypochlorite N/A
Carbon Dioxide (dry) B-Good Dimethyl Aniline D-Severe Effect Potassium Oxalate N/A
Carbon Dioxide (w et) B-Good Ethanolamine D-Severe Effect Sodium Hyposulfate N/A
Chromic Acid 10% B-Good Ethyl Acetate D-Severe Effect Sulfur Hexafluoride N/A
Ethylene Chloride B-Good Ethyl Ether D-Severe Effect Sulfuryl Chloride N/A
Ethylene Diamine B-Good Ethylene Oxide D-Severe Effect Uric Acid N/A
Ferrous Sulfate B-Good Formaldehyde 100% D-Severe Effect Zinc Hydrosulfite N/A
Fluoboric Acid B-Good Furan Resin D-Severe Effect
Hydrofluoric Acid 100% B-Good Furfural D-Severe Ef fect
Hydrofluoric Acid 50% B-Good Hydrogen Sulfide (aqua) D-Severe Effect
Hydrofluoric Acid 75% B-Good Hydrogen Sulfide (dry) D-Severe Effect
Hydroquinone B-Good Isopropyl Acetate D-Severe Effect
Lye: KOH Potassium Hydroxide B-Good Isopropyl Ether D-Severe Effect
Methylene Chloride B-Good Ketones D-Severe Effect