Peco PERFORMANCE PRO MULTI-FAN User manual

© COPYRIGHT 2013 PECO, INC. ALL RIGHTS RESERVED. P/N 70864 3220-2318 REV 00
SET CLOCK, YEAR, MONTH, DAY
1. Press ▲/ ▼ to select 12 or 24 HR mode, then
press Next.
2. Press ▲/ ▼to select hour, then press Next.
3. Press ▲/▼to select minutes, then press Next.
4. Press ▲/ ▼ to select current year, then press Next.
5. Press ▲/ ▼ to select current month, press Next.
6. Press ▲/ ▼ to select the calendar day number.
7. Press Done to complete operation.
Note: Select More > Clock, to access after setup.
ACCESS SERVICE MENUS
1. Hold lower right and lower left keys for fi ve
seconds.
2. Press Next or Go Back button to select a
Service Menu.
3. Press ▲/ ▼ to select option.
4. Press Done when complete.
CONFIGURE SERVICE MENUS
The following Service Menus (SM) commonly require
confi guration. Please verify that these are set for your
specifi c application. Additional confi guration may be
required. Refer to Table 2 for all available Service Menus.
• SM 100 = Programmable or Nonprogrammable
• SM 110 = System Type
• SM 121 = Number of Fan Speeds
• SM 130 = Reversing Valve
• SM 135 = W1 heat output NO or NC
• SM 170 = Remote Sensors
• SM 265 = Single or Dual Setpoint Operation
WIRING: TERMINAL DESIGNATIONS
1. Connect wires for appropriate system type
(Table 1).
WARNING: DISCONNECT POWER BEFORE BEGINNING INSTALLATION.
• CAUTION: Use copper wire only. Insulate or wire-nut all unused leads.
• Use care to avoid electrostatic discharge to thermostat
• CAUTION: Do not connect unused wires together
• ALL ELECTRICAL LOADS MUST BE CONNECTED TO TERMINAL C
(24 VAC).
TABLE 1. TERMINAL BLOCK DESIGNATIONS
Fan Coil (Conventional) Heat Pump
C24 VAC, Unswitched side C24 VAC, Unswitched side
W1 Stage 1 Heat B/O Reversing Valve
W2 Stage 2 Heat AUX Auxiliary Heat (Stage 2 or 3)
GFAN High GFAN High
AFAN Medium AFAN Medium
EFAN Low EFAN Low
Y1 Stage 1 Cool Y1 Compressor Stage 1
Y2 Stage 2 Cool Y2 Compressor Stage 2
RH 24 VAC Power for heating,
switched side RH 24 VAC Power for heating, switched side
RC 24 VAC Power for cooling,
switched side RC 24 VAC Power for cooling, switched side
SC Sensor Common SC Sensor Common
S1 Indoor Remote Sensor S1 Indoor Remote Sensor
S2 Occupancy Sensor S2 Occupancy Sensor
S3
Seasonal Changeover Switch
OPEN=Cooling in Summer
CLOSED=Heating in Winter
S3 NA
▲
!
1
4
3
2
Service
Menu
Current
option
QUICK START GUIDE
PERFORMANCE PRO MULTI-
FAN

© COPYRIGHT 2013 PECO, INC. ALL RIGHTS RESERVED. P/N 70864 3220-2318 REV 00
FAN SPEED SELECTION
1. Press the Fan button to select speed/operation.
Note: Fan Speed is noted as follows:
2. Press Done when complete.
ON = Continuous Fan Operation
AUTO = Fan Cycles with Heating and Cooling
MENU FEATURE OPTIONS STD. DEFAULT DESCRIPTION / COMMENTS
100 Schedule Format 0-3 1 Select the schedule format on the T8000 Series. (Menu not available on non-programmable
thermostats.)
0 = nonprogrammable
1 = programmable
2 = 5-1-1 schedule
3 = 5-2 schedule
101 Daylight-Saving
Time
0,1 0 Select daylight-saving time as it follows standard format in U.S.: It begins second Sunday of
March at 2:00 AM and ends on the  rst Sunday of November at 2:00 AM.
0 = Disabled
1 = Enabled (2007 U.S. Format)
110 System Type 1-13 1 Select the appropriate system con guration (determines available Service Menus).
1 = 1 Heat/1 Cool conventional
2 = 1 Heat/1 Cool heat pump
3 = Heat only without fan (2-wire systems)
4 = Heat only with fan
5 = Cool only
6 = 2 Heat/1 Cool heat pump (with auxiliary heat) and Emergency (Em) heat
7 = 2 Heat/2 Cool multistage conventional
8 = 2 Heat/ 1 Cool multistage conventional
9 = 1 Heat/ 2 Cool multistage conventional
10 = 2 Heat/ 2 Cool heat pump (no auxiliary heat)
11= 3 Heat/ 2 Cool heat pump (with auxiliary heat) and Emergency (Em) heat
12 = NA
13= NA
TABLE 2. ADVANCED CONFIGURATION: SERVICE MENUS
Some Service Menus may not be available, depending on system type (SM 110).
24 VAC Switched Side
OPEN= Summer CLOSED = Winter
C
WI
Y1
G
A
E
RH
RC
SC
S1
S2
S3
OCC Sensor
Aquastat
FAN LO
FAN MED
FAN HIGH
Cool Valve
Heat Valve
Sensor Common
Remote Sensor
24 VAC Unswitched
24 VAC
FAN HIGH
FAN MED
FAN LOW
Fan
Speed
icon
6
TYPICAL FAN COIL WIRING DIAGRAM
5

© COPYRIGHT 2013 PECO, INC. ALL RIGHTS RESERVED. P/N 70864 3220-2318 REV 00
MENU FEATURE OPTIONS STD. DEFAULT DESCRIPTION / COMMENTS
121 Fan Speeds 1, 2, 3, 4 3 Allows selection of multiple fan speeds.
1 = Single speed Fan (G terminal)
2 = 2-speed Fan (G and A Terminals)
3 = 3-speed Fan (G,A and E Terminals)
4 = 3-speed Staged Fan
130 O/B Reversing
valve
0,1 0 When 0, output is active for cooling. When 1, output is active for heating.
0 = (O) Active with cooling
1 = (B) Active with heating
135 W1 Output
Conguration
0,1 0 Changes operation of W1 for Active to Open (NC Normally Closed) to Active to Close (NO
Normally Open).
0 = NC Operation
1 = NO Operation
150 Backlight 0,1 0 0 = Backlight temporarily on
1 = Backlight always on (low intensity, 24V only)
170 Remote Sensor 0-8 0 Select sensor if used. Contact PECO for information on the T8000 Series Indoor Remote Zone Sensor.
0 = No Remote Sensors
1 = Remote Indoor Sensor Only
2 = Not Used
3 = Not Used
4 = Not Used
5 = Not Used
6 = S3 Input with Aquastat Only
7 = S3 Input with Aquastat and S1 with Remote Indoor Sensor
8 = Not Used
240 Number of Program
Periods
2; 4 events 4 2 = 2 events per day (Selections OCC1 and UnOcc1)
4 = 4 events per day (Selections Occ1-UnOcc1-Occ2- UnOcc2)
250 Clock format 12 or 24 Hours 12 12 = 12-hour clock mode
24 = 24-hour clock mode
260 Temperature Format
(°F or °C)
0,1 1 0 = Celsius
1 = Fahrenheit
265 Single/Dual Setpoint 0,1 1 Determines if single user override setpoint is used, or if user sets heat and cool setpoints independently.
0 = Dual Setpoint (Heat and Cool)
1 = Single Override Setpoint (Single Setpoint with auto changeover algorithm)
290 Range Low 50-90 °F or
10-32°C
50°F (10°C) Choose the lowest selectable temperature setpoint value.
300 Range High 50-90 °F or
10-32°C
90°F (32°C) Choose the highest selectable temperature setpoint value.
310 Setback Low Off; 50-82°F or
11-27°C
55°F (13°C) Temperature setpoint thermostat will Heat to when in Setback mode (Off sets Heating to ~45F Setback).
0 = Off
50-82°F (11-27°C)
320 Setback High Off; 58-90°F or
11-32°C
90°F (32°C) Temperature setpoint thermostat will Cool to when in Setback mode. (Off sets Cooling to ~150F in
Setback).
0 = Off (disabled)
58-90°F (11-32°C)
330 Zone Temp Offset +/-9°F or +/-
4.5°C
0°F (18 °C) Adjusts the sensed Zone Temperature displayed, allowing calibration in the eld.
340 Keypad Lockout 0-3 0 Restricts access to certain features of device; Service Menu still available if keypad lockout is enabled.
0 = No key pad lockout (Default)
1 = Disables Schedule and System keys
2 = Disables Schedule, System, and Fan keys
3 = Disables all keys
341 Enable Pin Access 0,1 0 Applies a 3 digit access code to enter Service Menu 342
0 = Disable
1 = Enable
342 Set PIN 000-999 000 Choose a 3-digit PIN access code.
350 Fan Mode 1-3 3 1 = ON: Fan is always on, regardless of demand
2 = Auto: Fan is only on with heating or cooling demand
3 = ON or Auto: Occupant can choose either selection
360 System Mode 0-3 1 Allows ability to determine which system modes the occupant can select.
0 = OFF, Auto
1 = OFF, Heat, Cool, Auto
2 = OFF, Heat, Cool
3 = Heat, Cool, Auto

© COPYRIGHT 2013 PECO, INC. ALL RIGHTS RESERVED. P/N 70864 3220-2318 REV 00
MENU FEATURE OPTIONS STD. DEFAULT DESCRIPTION / COMMENTS
375 Purge Enable 0-3 0 0 = No Purge
1 = W1 purge
2 = Y1 Purge
3 = W1 & Y1 purge
376 Purge Duration 1-3 1 De nes how long to open the valve to perform the purge function.
1 to 3 minutes
377 Purge Frequency 0-2 0 De nes how long to open the valve to perform the purge function.
0 = Every 24 Hours
1 = Every 12 Hours
2 = Every 6 Hours
380 Minimum Deadband
Adjustment
1-10°F, 0.5-5°C 3°F A changeover deadband value prevents short cycling between heating and cooling modes. The value is
adjustable to meet various HVAC system requirements.
395 Temporary Occupied
Duration Limit
0-4 hours 0 The temporary User Override is limited by the time de ned in this service menu.
0 = Remainder of time until the next scheduled event.
1 = 1 Hour
2 = 2 Hours
3 = 3 Hours
4 = 4 Hours
480 Minimum Off Time Range:
0-10 Minutes
4 Sets the minimum off time for both the heat and cool output.
500 Programmable/
Intermittent Fan
0-2 0 In programmable mode, fan will operate continuously during occupied periods or with demand during
unoccupied periods. In intermittent mode, fan will operate based on the on and off times set in menus
501 and 502 whenever there is no call for fan.
0 = Disable
1 = Programmable Fan: Fan operates continuously in occupied periods or with demand in
unoccupied periods.
2 = Intermittent Fan: Fan operates based on the on and off times set in menus 501 and 502.
501 Intermittent Fan On
Time
1-60 minutes 5 minutes De nes the duration in which fan low will be on. Fan On will be activated after Fan Off time has passed.
502 Intermittent Fan Off
Time
0-60 minutes 25 minutes De nes the duration in which fan low will be off. Fan Off will be activated after Fan On time has passed.
A selection of 0 will result in continuous Fan.
520 Default Display
Icons
0-4 0 Select icons that will be displayed in the Default Display screen.
0 = Time, Temp, SP
1 = Time, Temp
2 = Time only
3 = Temp only
4 = No Display
530 Revision — — Upon menu selection the  rmware revision,  rmware checksum and con guration checksum is
displayed.
540 Factory Default
Reset
0,1 0 When Enable is selected the device will return to factory default settings.
0 = Disable
1 = Enable
Note: Press “Done” key to complete process.
600 System Test Main
Output (Cool)
0-2 0If either stage is enabled it will activate the associated output for 10 minutes. The Fan output will
automatically turn on. If a different service menu is selected the output will be disabled.
0 = Disable
1= Cool Stage 1
2 = Cool Stage 2
610 System Test Main
Output (Heat)
0-3 0 If either stage is enabled it will activate the associated output for 10 minutes. The Fan output will
automatically turn on if con gured to do so. If a different service menu is selected the output will be
disabled. (Note: Aux heat could be stage 2 or stage 3 based on con guration)
0 = Disable (Default)
1 = Heat Stage 1
2 = Heat Stage 2
3 = Heat Stage 3
620 System Fan Test
Output
0-3 0 0 = Disabled
1 = Low Speed
2 = Medium Speed
3 = High Speed
900 Factory Use Only -- -- Factory Use Only
901 Factory Use Only -- -- Factory Use Only
902 Factory Use Only -- -- Factory Use Only
WARNING: Service Menu 375 may disable fan operation during valve
purge. This feature should be set to 0 (zero) unless outputs are connected
to hydronic heating or cooling valves. Failure to follow this instruction can
result in damage to equipment and/or property.
▲
!