PEERLESS SUT632P Guide

Installation and Assembly:
Peerless Ultra-Thin Tilt Mount for 22" to 40"* Flat Panel
Displays
Models: SUT632P
*Display Compatability Requirements
•Depth of display must be less than 2"
•The depth of this mount (0.68") may not provide sufficient space
for proper ventilation on some displays. Please refer to the
manufacturer's requirements for mounting your display before
installation.
• The display must have a flat mounting surface, or the mounting
holes need to be on the furthest back surface of the display.
• Input/Output connection must be properly oriented to accomodate
mounting 0.68" from the wall. Max UL Load Capacity: 60 lb (27.2 kg)
©
UL
USC
ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com

2 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood Stud Wall................................................................................................................................................4
Installation to Solid Concrete/Cinder Block walls ...................................................................................................................5
Installing Adapter Plate...........................................................................................................................................................6
Mounting and Removing Flat Panel Display...........................................................................................................................8
Tools Needed for Assembly
•stud finder ("edge to edge" stud finder is recommended)
•drill
• 5/16" (8mm) bit for concrete and cinder block wall
• 5/32" (4mm) bit for wood stud wall
•level
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US
customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact
your local distributor.
• This mount is designed to attach the display 0.68" from the wall. Please refer to manufacturer's installation guide
recommendations for required distance from wall to avoid risk of injury or property damage.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum UL Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of
an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal
injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION HARDWARE REQUIRED
• Wood Stud Included
•Wood Beam Included
•Solid Concrete Included
•Cinder Block Included
•Metal Stud Contact Qualified Professional (not evaluated by UL)
•Brick Contact Qualified Professional (not evaluated by UL)
•Other or unsure? Contact Qualified Professional
WARNING

3 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11
Parts may appear slightly different than illustrated.
A
B
Before you begin, make sure all parts shown are included with your product.
CEFGHI
KLM N OJ
PQ R
Description Qty. Part #
A
wall plate 1 046-P1058
Badapter plate 1 046-P1092
Cwood screws 2 500-1090
Dconcrete anchors 2 590-0320
EM4 x 12 mm phillips screw 6504-9013
FM4 x 25 mm phillips screw 4504-1015
GM5 x 12 mm phillips screw 4520-1027
HM5 x 25 mm phillips screw 4 520-9543
IM6 x 12 mm phillips screw 4520-1128
JM6 x 20 mm phillips screw 4 520-9402
KM6 x 25 mm phillips screw 4 520-1208
LM6 x 30 mm phillips screw 4 510-9109
MM8 x 16 mm phillips screw 6 520-9257
NM8 x 25 mm phillips screw 4 520-1031
OM8 x 40 mm phillips screw 4 520-1136
P.5" x .5" spacer 4 540-1057
Q.5 x .75" spacer 4 540-1059
Rmulti-washer 6 580-1036
S4 mm driver 1 560-1133
T4 mm allen wrench 1 560-9646
Parts List
D
S
T

4 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11
Installation to Wood Stud Wall
Wall plate (A) must be mounted to a single wood stud. Use a stud finder to locate the edges of the stud. Use of an
edge-to-edge stud finder is highly recommended. Based on the stud's edges, draw a vertical line down the stud’s
center. Place wall plate on wall as a template. The top mounting slots must be located 1.48" (38mm) above the
desired display center as shown in figure 1.1. Level wall plate, and mark the center of the two mounting holes.
Make sure that the mounting holes are on the stud centerline. Drill two 5/32" (4mm) dia. holes 2" (51mm) deep.
Make sure that the wall plate is level and secure wall plate using two wood screws (C) as shown in fig. 1.2.
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations. (not evaluated by UL)
WARNING
C
A
fig. 1.2
fig. 1.1
CENTER OF DISPLAY
A
STUD
1.48"
(38Mm)
1

5 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11
Installation to Solid Concrete or Cinder Block
Make sure that wall plate (A) is level and use wall
plate as a template to mark two mounting holes. The
top mounting slots should be located 1.48" (38mm)
above the desired display center as shown in figure
1.1 on page 4. Drill two 5/16" (8mm) dia. holes to a
minimum depth of 2.5" (64mm). Insert anchors (D) in
holes flush with wall as shown. Place wall plate over
anchors and secure with two wood screws (C). Level,
then tighten all fasteners.
C
A
D
SOLID CONCRETE CINDER BLOCK
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all at-
tached hardware and components.
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete anchors directly to load-
bearing concrete.
• Never attach concrete anchors to concrete covered
with plaster, drywall, or other finishing material.
If mounting to concrete surfaces covered with a
finishing surface is unavoidable (not evaluated by
UL), the finishing surface must be counterbored
as shown below. Be sure concrete anchors do not
pull away from concrete when tightening screws. If
plaster/drywall is thicker than 5/8" (16mm), custom
fasteners must be supplied by installer (not evaluated
by UL).
WARNING
1
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
drywall
plaster/
drywall
concrete concrete
1
3
2
D
Drill holes and insert anchors (D).
Place plate (A) over anchors (D) and secure with screws (C).
Tighten all fasteners.
A
S
D
C
concrete
surface

6 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11
Attaching Adapter Plate to Display using VESA 100 x 100
FOR VESA 100 x 100 MOUNTING PATTERN:
NOTE: Adapter plate (B) must be fully extended to access mounting holes.
Begin with the shortest length screw, hand thread through adapter adapter plate and spacer in that order into
display. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over
tighten. If screw cannot make three full turns into the display, select a longer length screw. Repeat for remaining
mounting holes and tighten screws.
NOTE: For displays with a hole pattern in a pocket, spacers (P or Q) go between adapter plate (B) and display.
2
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
WARNING
B
SCREW
DISPLAY
For displays with a hole
pattern in a pocket,
spacers (P,Q) go between
adapter plate (B) and
display.

7 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11
Attaching Adapter Plate to Display using VESA 200 x 200 and VESA 200 x 100
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the display inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to display or product may fail.
WARNING
Begin with longer length screw, hand thread through multi-washer, adapter plate and spacer in that order into
display. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over
tighten. If screw cannot make three full turns into the display, select a shorter length screw. Repeat for remaining
mounting holes and tighten screws.
NOTE: Multi-washers and spacers may not be used depending on type of display.
NOTE: For displays with a hole pattern in a pocket, spacers (P or Q) go between adapter plate (B) and display.
2
BB
For displays with a hole
pattern in a pocket,
spacers (P,Q) go between
adapter plate (B) and
display.
SCREW
SCREW
MULTI-WASHER
MULTI-WASHER
DISPLAY DISPLAY
200 x 200 VESA PATTERN 200 x 100 VESA PATTERN
Notes:
• Multi-washers and spacers may not be
used, depending upon the type of display.
• Use the corresponding hole in the multi-
washer that matches your screw size.
LARGE HOLE FOR M6 SCREWS
SMALL HOLE FOR M4 SCREWS
MEDIUM HOLE FOR M5 SCREWS
MULTI-WASHER

8 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11
B
B
B
AWALL
PLATE
FLANGES
fig. 3.1
DETAIL 1
Mounting and Removing Flat Panel Display
• Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel displays.
• Be careful not to pinch fingers when opening and closing mount from the wall.
WARNING
Fully extend tilt brackets (B) and move tilt brackets
toward wall plate (A) as shown in figure 3.1. Hook
the tilt bracket onto both sets of flanges on wall
plate as shown in detail 1. Be sure flanges of tilt
bracket is fully seated into wall plate flanges.
Tighten safety screws using allen wrench (T) to
lock down safety latches securing adapter plate to
wall plate as shown in detail 2. Reverse step 3 to
remove display.
3
DETAIL 2
SAFETY
LATCH
WALL
PLATE
SAFETY
SCREW
TILT
BRACKET
FLANGES
TILT
BRACKET
FLANGES
• Tilt bracket flanges must fully engage wall plate
flanges as shown in detail 1 or product damage
may occur.
CAUTION

9 of 38 ISSUED: 09-10-09 SHEET #: 202-9365-4 04-05-11
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
From the collapsed position, pull from top to achieve up to 15° of forward tilt as illustrated in detail 5.
For more tilt adjustment, slightly pull out bottom and pull from top to desire tilt angle.
5
DETAIL 5
123
Tilt Angle Adjustment
To collapse adapter plate, grasp top and bottom of display, push bottom of display toward wall then push top of
display toward wall as illustrated in detail 3.
To extend adapter plate and access back of display, grasp top and bottom of display, pull top of display away
from wall then pull bottom of display away from wall as illustrated in detail 4.
4
DETAIL 3
DETAIL 4
123
123
Peerless Industries, Inc.
2300 White Oak Circle
Aurora, Il 60502
www.peerlessmounts.com

Instalación y ensamblaje:
Soporte inclinación Peerless Ultra-Delgado para
pantallas planas de 22" a 40"*
Modelos: SUT632P
*Requisitos para la compatibilidad de las pantallas
• La profundidad de la pantalla tiene que ser menos de 2".
• Es posible que la profundidad del soporte (0.68") no proporcione suficiente
espacio para la ventilación adecuada de algunas pantallas. Por favor,
repase los requisitos del fabricante en relación con la instalación de la
pantalla antes de proceder.
• La pantalla tiene que tener una superficie plana para la instalación o tiene
que tener los agujeros de montaje en la superficie trasera más alejada de la
pantalla.
• La conexión de entrada / salida tiene que tener la orientación adecuada
para acomodar una instalación a 0.68" de la pared. Capacidad máxima de soportar carga
por UL: 60 lb (27.2 kg)
©
UL
USC
PUBLICADO: 09-10-09 HOJA #: 202-9365-4 04-05-11
2300 White Oak Circle • Aurora, Il 60502 • [phone] • Fax: [phone] • www.peerlessmounts.com