Pelonis HC-1010 User manual

HC-1010

IMPORTANT INSTRUCTIONS
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances,basic precautions should always be followed to
reduce the risk of fire,electric shock,and injury to persons,including the following:
1. Read all instructions before using heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot
surface. If provided, always use handles when moving this heater. Keep
combustible materials such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet (0.9m) from the front of the heater and keep them away
from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or
invalids and whenever the heater is left operating and unattended.
4. Always unplug the heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Discard heater or
return heater to authorized service facility for examination, electrical or
mechanical adjustment, or repair.
6. Do not use the heater outdoors.
7. This heater is not intended for use in bathroom, laundry areas and similar moist
indoor locations. Never locate heater where it may fall into a bathtub or other
water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be tripped over.
9.
CAUTION: This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of shock, this plug is intended to fit only one way in a
polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. DO NOT attempt to defeat this
safety feature. To do so could result in an electric shock hazard.
10. This heater draws 12.5 amps during operation. To prevent overloading a
circuit, do not plug the heater into a circuit that already has other appliances
working.
11.
CAUTION: It is normal for the plug to feel warm to the touch; however, a loose
fit between the AC outlet (receptacle) and plug may cause overheating and
distortion of the plug. Contact a qualified electrician to replace loose or worn
outlet.
1

12. To disconnect the heater, first turn controls to off, then remove plug from
outlet. Never pull by the cord.
13. Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the heater.
14. To prevent a possible fire, do not block air intakes or exhaust in any manner.
Do not use on soft surface, like a bed, where openings may become blocked.
15. A heater has hot and arcing or sparking parts inside. Do not use it in the areas
where gasoline, paint, or flammable liquids are used or stored.
16. Use this heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or injury to
persons.
17.
CAUTION: Always plug heaters directly into a wall outlet/receptacle. Never
use with an extension cord or reloadable power tap (outlet/power strip).
18. The output of this heater may vary and its temperature may become intense
enough to burn exposed skin. Use of this heater is not recommended for
persons with reduced sensitivity to heat or an inability to react to avoid burns.
19. Disposal of oil contained within should be in accordance with applicable
regional, national, and local laws and regulations.
20.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
21. “SAVE THESE INSTRUCTIONS”
2

STRUCTURAL SKETCH
Machine components
Control panel
Rear cover
Air outlet
Display
screen
Remote control
storage port
3

CHECK BEFORE STARTUP
USAGE
1. Whether the power cord is in good condition.
2. The power supply for the product is 120V AC, and the carrying capacity of the socket shall
not be lower than 12.5A. Otherwise, accidents may occur.
[Start the machine]
Plug in the power and press the ON/Standby button of the control panel to start the machine.
After starting, the machine will run in the previous mode.
"+" button
ON/Standby button
"-" button
Timing
button
Gear button
Oscillating
button Display window
Plug in the power, press the "ON/Standby" button to enter the ON mode, and the
heater starts to work. The whole machine runs at the previous mode and temperature.
Press the "On/Standby" button in the startup mode to enter the standby mode, and the
heater will stop working.
After starting up, press the "gear" button repeatedly, and the heater will switch
according to the recursive sequence of "energy-saving mode → breeze → low warm
air → high warm air".
Button Functional description
Under ON mode, press the button to turn on the oscillating head, and then press the
button to turn off the oscillating head.
Power/ Standby
button
Gear button
+/-
button
Timing button
Oscillating button
When the machine is in operation, press the "+" or "-" button toset the operating
temperature. The temperature setting range is 40 - 95°F, with an interval of 1°F
between adjacent temperature values. If there is no operation within 3 seconds after
setting, the set temperature value will be confirmed and displayed. When the room
tempe rature reaches the set temperature, the display screen flashes for 10s, and the
heating element stops working. When the temperature is lower than the set
temperature, the machine starts heating again.
Under ON mode, press the button to select the timing shutdown setting, the timing
indicator lights up, the temperature display icon goes out, and the display screen
flashes to display the remaining time set last time. The shutdown time can be set
through the "+" and "-" buttons, with the setting range of 0-24 hours. If there is no
button action within 5 seconds, it will confirm the timing time and exit the timing
setting state. If the set timing time is 0, it means to cancel the timing setting. If the set
timing time is not 0, the machine automatically shuts down and goes into standby
mode when the set time is reached, and the timing indicator is out. Set the timing time
again after setting the timing time, and the timing is also re-timed. In the standby
mode, you press the button to make reserved startup setting, and the operation is the
same as timed shutdown. Timer time unit is hour.
4

Screen-off function
When the machine is in the working state, the screen will go out automatically if there is no
operation for 1 minute, and only the operation mode logo will be kept on. Press and hold the " "
and "-" buttons for 2 seconds at the same time to turn off the screen extinguishing function, then
press and hold the " " and "-" buttons for 2 seconds at the same time again to turn on the screen
extinguishing function.
Short-circuit Temperature Control Sensor, Open Circuit Protection
In any mode, if the temperature limiter has short circuit and open circuit protection, and the digital
screen displays "E1" or "E2" and keeps flashing, pressing any button will not work. The buzzer
sounds 10 times.
Safety protection
Tip-over protection
When it is in the ON state and indoor ambient temperature Th is higher than 122°F, the system will turn
off all the outputs, the digital screen will display "FF" and flash at a frequency of 1 time/second; then,
pressing any button will not work, and the protection can only be withdrawn if the power is cut off.
Either in the ON or OFF state, when the machine dumps, the system will immediately turn off all
the heating components and display "E3"; then, pressing any button will not work.
Turn Off Buttons' Decorative Lights and Buzzers
In the ON state, press the "timing button" and "gear button" for 2 seconds at the same time to turn off
the output of the buttons' decorative lights and buzzers. Repeat the operation toturn on this function.
Child Lock
Either in the ON or OFF state, the child lock will be opened when you press and hold "+" and "-"
buttons simultaneously for 2 seconds for the first time. Repeat the operation to turn off this function.
Remote controller
Remote control usage: The key function is consistent with those on the operation panel. Note:
Press the "< >" button of the remote control to enter the highly warm air mode with one button.
ECO mode
In ECO mode, press "+, -" to set the required temperature. When the ambient temperature is lower
than the set temperature (lower than 4°F or above), the product will be heated in a highly warm air
state; when the ambient temperature is close to the set temperature (lower than 4°F), the product
will be heated in a lower warm air state; when the ambient temperature is higher than the set
temperature, the product will stop heating.
5

HC-1010 800 1500
MAIN PARAMETERS
Rated voltage: 120V ~ 60Hz
Model Power adjustment range
Low-gear High gear
TROUBLESHOOTING
Problem
After the power is
switched on, the power
indicator does not turn
on, and the machine
does not work.
Shutdown suddenly
occurs in heating
Possible cause
The plug is not plugged
in properly
The temperature exceeds
the threshold of the
temperature limiter.
Solutions
Check whether the plug is inserted in
the socket properly
Use it after the machine is cooled
If the product does not operate or does not operate properly, first check according to the following
list. If the reason the product does not operate or does not operate properly is not included in the
following list, the product mayhave failed. At this time, it is recommended to send the product to
the dealer for treatment.
6
1. Do not dispose of batteries in fire, batteries may explode or leak.
2. Do not mix old and new batteries.
3. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries.
4. Non-rechargeable batteries are not to be recharged.
5. Batteries are to be inserted with the correct polarity.
6. Exhausted batteries are to be removed from the product.
7. The batteries must be removed from the remote controller before it is scrapped
and that they are disposed of safely.
BATTERY WARNING

SERVICE & SUPPORT
7