Pelonis HO-0203D User manual

OWNER’S MANUAL
Convection
Oil Filled
Radiator
Heater
Model HO-0203D
PLEASE READ AND SAVE THESE INSTRUCTIONS
IMPORTANT INSTRUCTIONS
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electric shock, and injury to persons, including the following:
1. Read all instructions before using this heater.
2. This heater is hot when in use
. To avoid burns, do not let bare skin touch hot surfaces.
If provided, use handles when moving this heater. Keep combustible materials, such
as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from
the front of the heater and keep them away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or invalids
and whenever the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner. Return heater to
authorized service facility for examination, electrical or mechanical adjustment, or
repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. Never locate heater where it may fall into bathtub or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar
coverings. Arrange cord away from traffic area and where it will not be tripped over.
9. To disconnect heater, first turn controls to off, then remove plug from outlet.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this
may cause an electric shock or fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not
use on soft surfaces, like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where
gasoline, paint, or flammable liquids are used or stored.
13. Use this heater only as described in this manual. Any other use not recommended by
the manufacturer may cause fire, electric shock, or injury to persons.
14. Avoid the use of an extension cord because the extension cord may overheat and
cause a risk of fire. However, if you have to use an extension cord, the cord shall be
No. 14 AWG minimum size and rated no less than 1875 watts.
15. This heater draws 12.5 amps during operation. To prevent overloading a circuit, do
not plug the heater into a circuit that already has other appliances working.
16. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC
outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact
a qualified electrician to replace loose or worn outlet.
17. The output of this heater may vary and its temperature may become intense enough to
burn exposed skin. Use of this heater is not recommended for persons with reduced
sensitivity to heat or an inability to react to avoid burns.
18.“SAVE THESE INSTRUCTIONS”

Place the heater on a firm level surface free from obstructions, and at least 3 ft. away
from any wall and any other objects such as furniture, curtains, plants or combustible
material.
To program the functions of your electronic oil filled heater, refer to the control panel
in Fig. 2.
Press the “ POWER” button to turn the heater ON.
Select the power you desire by pressing the POWER button, the heater circularly in
sequence of LO – MED– HI. On LO, the heater operates at 600W. On MED, the heater
operates at 900W. On HI, the heater operates at 1500W.
There are 5 positions from MIN to MAX. Press the “ TEMP SETTING” button to select
the desired temperature, the heater circularly in sequence of 65 oF– 70 oF– 75 oF– 80 oF–
85oF.
Press the “ TIMER SETTING” button to select the desired temperature. There are 3
positions from 2H to 8H.
Timer setting: This heater has an 8 hours On/Off timer. You can set an “ On” timer when the
heater is standing by (plug in but not working) or you can set an “ Off” timer when the heater is
working. For example, you can plug in the heater and set the timer to turn the heater on after 2
hours, you can also set the timer to turn the heater off after 4 hours when the heater is working.
When each timer is set, the green light will remain on, indicating that the timers have been set.
During operation, when the heater operates in the Time Set mode, the green light will turn red,
indicating that the heater is operating during its set time.
UNPACKING AND SET-UP INSTRUCTIONS
Unpack your heater and remove the wheel assemblies from the package. Refer to Fig. 1
below:
1. Make sure the heater is unplugged and in
the “ OFF” position.
2. TURN THE HEATER UPSIDE DOWN.
3. Position the wheel base assemblies
between the end fins as shown.
4. Insert each U-shape screw into the holes
of each wheel holding plate.
5. Insert the butterfly nuts and screw them
tightly.
6. Turn the heater upright.
Your heater is now ready for use.
CAUTION: Risk of fire – Do not operate heater without wheel assemblies attached. Operate
heater in upright position only (wheels on bottom, controls on top). Any other position could
create a hazardous situation.
OPERATING INSTRUCTIONS
Fig. 2 - Control Panel View
IMPORTANT!
Your heater is equipped with a
polarized alternating current
line plug (a plug having one
blade wider than the other).
This plug will fit into the power
outlet only one way. This is a
safety feature. If you are
unable to insert the plug fully
into the outlet, try reversing the
plug. If the plug should still fail
to fit, contact your electrician to
replace your outlet. DO NOT
defeat the safety purpose of
the polarized plug.
Fig. 1
-
Upside down view
Wheel
holding
plate
U
-
shape
screw

Example for “ On” Timer:
1. When the heater is plugged in and not working, press “ Timer” button, the Indicator Light
will display. Press the “ Timer” button circularly in sequence of 2H – 4H– 8H to choose your
desired timer setting.
2. Press the “ Timer” button and the Indicator Light for 2H will display.
Now your heater is set to be turned on after 2 hours.
Example for “ Off” Timer:
1. When the heater is working, press “ Timer” button, the Indicator Light will display . Press
the “ Timer” button circularly in sequence of 2H – 4H– 8H to choose your desired timer
setting.
Press the “ Timer” button and the Indicator Light for 2H will display.
Now your heater is set to be turned off after 2 hours.
To disable the timer, adjust the set value of the POWER to OFF.
Note: Once the timer is set, the heater will work this way automatically unless you changed the
set value or shut it off.
CAUTION: This heater includes an Overheat Protection System that shuts the unit off if it
overheats due to abnormal conditions. At this time, the “C” Caution Indicator Light gets on. If this
occurs turn the heater “OFF”, unplug it, and inspect and remove any objects on or adjacent to the
heater. Allow it to cool for a few minutes, plug it back in, and resume normal operation.
ADDITIONAL FEATURES
This heater has additional features:
Convenient front Carry Handles and Heavy-Duty Caster Wheels - Allow for easy
maneuvering from room to room.
Cord Storage Compartment - Neatly stores power cord when the heater is not
used.
TROUBLESHOOTING
If your heater fails to operate, please follow these instructions:
Ensure that your circuit breaker or fuse is working properly.
Be sure the heater is plugged in and that the electrical outlet is working properly.
Check for any obstruction. If you find any obstruction, turn the heater “ OFF” .
Unplug the heater and wait a few minutes for it to cool down. Carefully remove the
obstruction. Plug the heater in and turn it on again by referring to the OPERATING
INSTRUCTIONS.
NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEE THE
WARRANTY INFORMATION FOR INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO
OPEN OR REPAIR THE HEATER YOURSELF. DOING SO MAY VOID THE WARRANTY
AND COULD CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM STILL
PERSISTS, PLEASE CONTACT US BY REFERRING TO THE SERVICE & SUPPORT
INFORMATION ON THE FOLLOWING PAGE.
CLEANING AND STORAGE
It is recommended that the heater be cleaned at least one time during the operating
season in order to provide the optimum level of performance. ALWAYS TURN THE
POWER SWITCH OFF AND UNPLUG THE HEATER BEFORE CLEANING. Be sure
to save the box for off-season storage.
Turn the heater “ OFF” , unplug it and wait for the heater to cool down.
Use a dry cloth to clean only external surfaces of the heater.
Do not use any cleaning agents or detergents.
Never immerse the heater in water.
Pack the heater in the original carton and store it in a cool and dry place.
SPECIFICATIONS
Model No.: HO-0203D
Voltage: 120V, 60Hz
Current: Maximum continuous draw: 12.5 Amps.
Output: 5200 BTUs
Power: LOW = 600 Watts, MED = 900 Watts, HIGH = 1500 Watts
Tolerances on all specifications: Approximately +5%, -10%.
SERVICE & SUPPORT
In the event of a warranty claim or if service is required for this heater, please contact us at
the following:
Tel: [phone] (M-F 8:30am to 5:30pm CST)
Email us at: M[email protected]
For questions or comments, please write to:
PELONIS.
2617 North Great Southwest Parkway
Suite 100
Grand Prairie, TX 75050, USA
For your records, staple your sales receipt to this manual and record the following:
DATE OF PURCHASE: ________________________________
________________________________
PLACE OF PURCHASE: ________________________________
________________________________
SERIAL NUMBER:________________________________
________________________________
(STAPLE SALES RECEIPT HERE)
NOTE: PROOF OF PURCHASE IS REQUIRED FOR ALL WARRANTY
CLAIMS

ONE (1) YEAR LIMITED WARRANTY
Please read all instructions before attempting to use this product.
Please return the Warranty Registration card within fifteen (15) days from the date of
purchasing this product.
PELONIS warrants as limited herein to the original purchaser of retail that each new Pelonis Oil
Filled Radiator heater shall be free of defects in material and workmanship for a period of one
(1) year from the date of original purchase. This one (1) year warranty is limited to the heating
elements, motor, and electric control circuit board.
In the event of malfunctions or failure of your Pelonis Fan Forced heater, simply deliver or send
the heater, postage prepaid along with PROOF OF PURCHASE, within the warranty period of
one (1) year, to PELONIS. PELONIS reserves the right to inspect the claimed defective part or
parts to determine if the defect or malfunction complaint is covered by this warranty. PELONIS
shall, within sixty (60) days after receipt of the product, at its option, repair and/or replace the
defective part or parts free of charge. This warranty shall only cover defects arising from normal
usage. PELONIS assumes no responsibility whatsoever if the Fan Forced heater should fail
during the warranty period by reason of:
Misuse, negligence, physical damage or accidents.
Lack of maintenance (see instructions for proper maintenance).
Repair by any unauthorized party during the warranty period.
Damage caused by connection to an improper input voltage (see specification label on
your heater).
PELONIS makes no further warranties or representations, express or implied except those
contained herein. No representative or dealer is authorized to assume any other liability
regarding the Fan Forced heater. The duration of the implied warranty granted under State law,
including warranties of merchantability and fitness for particular purpose are limited in duration
should the duration of the express warranty grant it hereunder. PELONIS shall in no event be
liable for direct, indirect, special or consequential damages.
Some states do not allow limitations on how long an implied warranty lasts, and/or the above
limitations or exclusion may not apply to you. This warranty gives you specific legal rights and
you may have other rights which vary from state to state.