Pentair Fleck 2510 ECONOMINDER User manual

Model 2510 & 2510 Econominder
Service Manual
IMPORTANT: Fill in Pertinent Information on Page 3 for Future Reference
CLICK ANYWHERE on THIS PAGE to RETURN to WATER SOFTENER MANUALS at InspectApedia.com

Job Specification Sheet......................................................................................................................................... 3
Installation Instructions.......................................................................................................................................... 4
Start-Up Instructions.............................................................................................................................................. 5
3200 Timer Setting Procedure............................................................................................................................... 6
3210 Timer Settings............................................................................................................................................... 7
3200 & 3210 Timer Series ..................................................................................................................................... 8
3200 Timer Assembly .......................................................................................................................................... 10
3210 Timer Assembly .......................................................................................................................................... 12
Powerhead Assembly.......................................................................................................................................... 14
Powerhead Assembly (Environmental)................................................................................................................ 16
Manual Powerhead Assembly ............................................................................................................................. 18
Control Valve Assembly....................................................................................................................................... 20
Softener & Filter Conversion Kits ........................................................................................................................ 22
Meter Assembly................................................................................................................................................... 23
1600 Brine System Assembly.............................................................................................................................. 24
1650 Brine System Assembly.............................................................................................................................. 25
Bypass Valve Assembly (Plastic)......................................................................................................................... 26
Bypass Valve Assembly (Metal) .......................................................................................................................... 27
2300 Safety Brine Valve ...................................................................................................................................... 28
2310 Safety Brine Valve ...................................................................................................................................... 29
Service Instructions ............................................................................................................................................. 30
Seal & Spacer Replacement ............................................................................................................................... 31
Troubleshooting................................................................................................................................................... 33
Flow Data & Injector Draw Rates ........................................................................................................................ 35
Wiring Diagram.................................................................................................................................................... 36
Service Assemblies ............................................................................................................................................. 37
Table of Contents
IMPORTANT PLEASE READ:
The information, specifications and illustrations in this manual are based on the latest information available at the time of•
printing. The manufacturer reserves the right to make changes at any time without notice.
This manual is intended as a guide for service of the valve only. System installation requires information from a number of•
suppliers not known at the time of manufacture. This product should be installed by a plumbing professional.
This unit is designed to be installed on potable water systems only.•
This product must be installed in compliance with all state and municipal plumbing and electrical codes. Permits may be•
required at the time of installation.
If daytime operating pressure exceeds 80 psi (5.5 bar), nighttime pressures may exceed pressure limits. A pressure reducing•
valve must be installed.
Do not install the unit where temperatures may drop below 32°F (0°C) or above 110°F (43°C).•
Do not place the unit in direct sunlight. Black units will absorb radiant heat increasing internal temperatures.•
Do not strike the valve or any of the components.•
Warranty of this product extends to manufacturing defects. Misapplication of this product may result in failure to properly•
condition water, or damage to product.
A prefilter should be used on installations in which free solids are present.•
In some applications local municipalities treat water with Chloramines. High Chloramine levels may damage valve components.•
Correct and constant voltage must be supplied to the control valve to maintain proper function.•

Job Number: __________________
Model Number: ________________
Water Hardness: ___________________ ppm or gpg
Capacity Per Unit: ______________
Mineral Tank Size: ___________ Diameter: ___________ Height:
Salt Setting per Regeneration: _____________________________________________
1. Type of Timer:
A. 7 Day or 12 Day B. Meter Initiated
2. Downflow: Upflow Upflow Variable
3. Meter Size:
A. 3/4” Std Range (125 - 2,100 gallon setting)
B. 3/4” Ext Range (625 - 10,625 gallon setting)
C. 1” Std Range (310 - 5,270 gallon setting)
D. 1” Ext Range (1,150 - 26,350 gallon setting)
E. 1-1/2” Std Range (625 - 10,625 gallon setting)
F. 1-1/2” Ext Range (3,125 - 53,125 gallon setting)
G. 2” Std Range (1,250 - 21,250 gallon setting)
H. 2” Ext Range (6,250 - 106,250 gallon setting)
I. 3” Std Range (3,750 - 63,750 gallon setting)
J. 3” Ext Range (18,750 - 318,750 gallon setting)
K. Electronic________ Pulse Count ________ Meter Size
4. System Type:
A. System #4: 1 Tank, 1 Meter, Immediate, or Delayed Regeneration
B. System #4: Time Clock
C. System #4: Twin Tank
D. System #5: 2-5 Tanks, 2 Meters, Interlock
E. System #6: 2-5 Tanks, 1 Meter, Series Regeneration
F. System #7: 2-5 Tanks, 1 Meter, Alternating
G. System #9: Electronic Only, 2-4 Tanks, Meter per Valve, Alternating
H. System #14: Electronic Only, 2-4 Tanks, Meter per Valve. Brings units on and offline based on flow.
5. Timer Program Settings:
A. Backwash: ______________________ Minutes
B. Brine and Slow Rinse: _____________ Minutes
C. Rapid Rinse: ____________________ Minutes
D. Brine Tank Refill: _________________ Minutes
E. Pause Time: ____________________ Minutes
F. Second Backwash: _______________ Minutes
6. Drain Line Flow Control: ____________ gpm
7. Brine Line Flow Controller: __________________ gpm
8. Injector Size#: _____________________
9. Piston Type:
A. Hard Water Bypass
B. No Hard Water Bypass
Job Specification Sheet

Page 4
Installation Instructions
WATER PRESSURE: A minimum of 20 pounds of water pressure (1.3 bar) is required for regeneration valve to operate
effectively.
ELECTRICAL FACILITIES: An uninterrupted alternating current (A/C) supply is required. Note: Other voltages are
available. Please make sure your voltage supply is compatible with your unit before installation.
EXISTING PLUMBING: Condition of existing plumbing should be free from lime and iron buildup. Piping that is built
up heavily with lime and/or iron should be replaced. If piping is clogged with iron, a separate iron filter unit should be
installed ahead of the water softener.
LOCATION OF SOFTENER AND DRAIN: The softener should be located close to a drain to prevent air breaks and
back flow.
BY-PASS VALVES: Always provide for the installation of a by-pass valve if unit is not equipped with one.
CAUTION: Water pressure is not to exceed 125 psi (8.6 bar), water temperature is not to exceed 110°F (43°C), and the
unit cannot be subjected to freezing conditions.
Installation Instructions
Place the softener tank where you want to install the unit making sure the unit is level and on a firm base.1.
During cold weather, the installer should warm the valve to room temperature before operating.2.
All plumbing should be done in accordance with local plumbing codes. The pipe size for residential drain line should3.
be a minimum of 1/2” (13 mm). Backwash flow rates in excess of 7 gpm (26 Lpm) or length in excess of 20’ (6 m)
require 3/4” (19 mm) drain line. Commercial drain lines should be the same size as the drain
line flow control.
Refer to the dimensional drawing for cutting height of the distributor tube. If there is no4.
dimensional drawing, cut the distributor tube flush with the top of the tank.
Lubricate the distributor O-ring seal and tank O-ring seal. Place the main control valve on5.
tank. Note: Only use silicone lubricant.
Solder joints near the drain must be done prior to connecting the Drain Line Flow Control6.
fitting (DLFC). Leave at least 6” (15 cm) between the DLFC and solder joints when soldering
pipes that are connected on the DLFC. Failure to do this could cause interior damage to the
DLFC.
Teflon tape is the only sealant to be used on the drain fitting. The drain from twin tank units7.
may be run through a common line.
Make sure that the floor is clean beneath the salt storage tank and that it is level.8.
Place approximately 1” (25 mm) of water above the grid plate. If a grid is not utilized, fill to9.
the top of the air check (Figure 1) in the salt tank. Do not add salt to the brine tank at this
time.
On units with a by-pass, place in by-pass position. Turn on the main water supply. Open a10.
cold soft water tap nearby and let run a few minutes or until the system is free from foreign
material (usually solder) that may have resulted from the installation. Once clean, close the
water tap.
Slowly place the by-pass in service position and let water flow into the mineral tank. When11.
water flow stops, slowly open a cold water tap nearby and let run until the air is purged from
the unit.
Plug unit into an electrical outlet. Note: All electrical connections must be connected12.
according to local codes. Be certain the outlet is uninterrupted.
60002-34REVC
Figure 1 Residential
Air Check Valve

Page 5
Start-Up Instructions
The water softener should be installed with the inlet, outlet, and drain connections made in accordance with the
manufacturer’s recommendations, and to meet applicable plumbing codes.
Turn the manual regeneraton knob slowly in a clockwise direction until the program micro switch lifts on top of1.
the first set of pins. Allow the drive motor to move the piston to the first regeneration step and stop. Each time
the program switch position changes, the valve will advance to the next regeneration step. Always allow the
motor to stop before moving to the next set of pins or spaces.
NOTE: For electronic valves, please refer to the manual regeneration part of the timer operation
section. If the valve came with a separate electronic timer service manual, refer to the timer operation
section of the electronic timer service manual.
Position the valve to backwash. Ensure the drain line flow remains steady for 10 minutes or until the water2.
runs clear (see above).
Position the valve to the brine / slow rinse position. Ensure the unit is drawing water from the brine tank (this3.
step may need to be repeated).
Position the valve to the rapid rinse position. Check the drain line flow, and run for 5 minutes or until the water4.
runs clear.
Position the valve to the start of the brine tank fill cycle. Ensure water goes into the brine tank at the desired5.
rate. The brine valve drive cam will hold the valve in this position to fill the brine tank for the first regeneration.
Replace control box cover.6.
Put salt in the brine tank.7.
NOTE: Do not use granulated or rock salt.

Page 6
3200 Timer Setting Procedure
How To Set Days On Which Water Conditioner Is To
Regenerate (Figure 2):
Rotate the skipper wheel until the number “1” is at the
red pointer. Set the days that regeneration is to occur
by sliding tabs on the skipper wheel outward to expose
trip fingers. Each tab is one day. Finger at red pointer is
tonight. Moving clockwise from the red pointer, extend
or retract fingers to obtain the desired regeneration
schedule.
How To Set The Time Of Day:
1. Press and hold the red button in to disengage the
drive gear.
2. Turn the large gear until the actual time of day is at
the time of day pointer.
3. Release the red button to again engage the drive
gear.
How To Manually Regenerate Your Water
Conditioner At Any Time:
1. Turn the manual regeneration knob clockwise.
2. This slight movement of the manual regeneration
knob engages the program wheel and starts the
regeneration program.
3. The black center knob will make one revolution in
the following approximately three hours and stop in
the position shown in the drawing.
4. Even though it takes three hours for this center knob
to complete one revolution, the regeneration cycle of
your unit might be set only one half of this time.
5. In any event, conditioned water may be drawn after
rinse water stops flowing from the water
conditioner drain line.
How to Adjust Regeneration Time:
1. Disconnect the power source.
2. Locate the three screws behind the manual
regeneration knob by pushing the red button in and
rotating the 24 hour dial until each screw appears in
the cut out portion of the manual regeneration knob.
3. Loosen each screw slightly to release the pressure
on the time plate from the 24 hour gear.
4. Locate the regeneration time pointer on the inside
of the 24 hour dial in the cut out.
5. Turn the time plate so the desired regeneration time
aligns next to the raised arrow.
6. Push the red button in and rotate the 24 hour dial.
Tighten each of the three screws.
7. Push the red button and locate the pointer one more
time to ensure the desired regeneration time
is correct.
8. Reset the time of day and restore power to the unit.
Figure 2 61502_3200REVA

Page 7
3210 Timer Settings
Page 7
Typical Programming Procedure
Calculate the gallon capacity of the system, subtract
the necessary reserve requirement and set the gallons
available opposite the small white dot on the program
wheel gear.
NOTE: Drawing shows 8,750 gallon setting. The
capacity (gallons) arrow (15)shows zero gallons
remaining. The unit will regenerate tonight at the set
regeneration time.
How To Set The Time Of Day:
Press and hold the red button in to disengage the1.
drive gear.
Turn the large gear until the actual time of day is2.
opposite the time of day pointer.
Release the red button to again engage the drive3.
gear.
How To Manually Regenerate Your Water
Conditioner At Any Time:
Turn the manual regeneration knob clockwise.1.
This slight movement of the manual regeneration2.
knob engages the program wheel and starts the
regeneration program.
The black center knob will make one revolution in the
following approximately three hours and stop in the
position shown in the drawing.
Even though it takes three hours for this center3.
knob to complete one revolution, the regeneration
cycle of your unit might be set for only one half of
this time.
In any event, conditioned water may be drawn after4.
rinse water stops flowing from the water conditioner
drain line.
Immediate Regeneration Timers:
These timers do not have a 24 hour gear. Setting the
gallons on the program wheel and manual regeneration
procedure are the same as previous instructions. The
timer will regenerate as soon as the capacity gallons
reaches zero.
NOTE:
The program wheel to the
left may be different than the
program wheel on the product.
NOTE:
To set meter capacity rotate
manual knob one - 360°
revolution to set gallonage.
Figure 3
61502_3200REVA

Page 8
3200 & 3210 Timer Series
How To Set The Regeneration Cycle Program:
The regeneration cycle program on your water
conditioner has been factory preset, however,
portions of the cycle or program may be lengthened or
shortened in time to suit local conditions.
3200 & 3210 Series Timers (Figure 4)
To expose cycle program wheel, grasp timer in1.
upper left-hand corner and pull, releasing snap
retainer and swinging timer to the right.
To change the regeneration cycle program, the2.
program wheel must be removed. Grasp program
wheel and squeeze protruding lugs toward center,
lift program wheel off timer. Switch arms may
require movement to facilitate removal.
Return timer to closed position engaging snap3.
retainer in back plate. Make certain all electrical
wires locate above snap retainer post.
Timer Setting Procedure for 3200 & 3210
Timer
How To Change The Length Of The Backwash
Time:
The program wheel as shown in the drawing is in the
service position. As you look at the numbered side of
the program wheel, the group of pins starting at zero
determines the length of time your unit will backwash.
EXAMPLE: If there are six pins in this section, the time
of backwash will be 12 min. (2 min. per pin). To change
the length of backwash time, add or remove pins as
required. The number of pins times two equals the
backwash time in minutes.
How To Change The Length Of Brine And Rinse
Time:
The group of holes between the last pin in the1.
backwash section and the second group of pins
determines the length of time that your unit will
brine and rinse (2 min. per hole).
To change the length of brine and rinse time, move2.
the rapid rinse group of pins to give more or fewer
holes in the brine and rinse section. Number of
holes times two equals brine and rinse time in
minutes.
How To Change The Length Of Rapid Rinse:
The second group of pins on the program wheel1.
determines the length of time that your water
conditioner will rapid rinse (2 min. per pin).
To change the length of rapid rinse time, add or2.
remove pins at the higher numbered end of this
section as required. The number of pins times two
equals the rapid rinse time in minutes.
How To Change The Length Of Brine Tank Refill
Time:
The second group of holes in the program wheel1.
determines the length of time that your water
conditioner will refill the brine tank (2 min. per hole).
To change the length of refill time, move the two2.
pins at the end of the second group of holes as
required.
The regeneration cycle is complete when the outer3.
microswitch is tripped by the two pin set at end of
the brine tank refill section.
The program wheel, however, will continue to rotate4.
until the inner micro-switch drops into the notch on
the program wheel.
Regeneration Cycle Program Setting Procedure
(Downflow)
Figure 4
61502_3210REVA

Page 9
Notes

Page 10
3200 Timer Assembly
For Service Assembly Numbers, See the Back of this Manual
61502-3200_REVA

Page 11
3200 Timer Assembly
Item No. Quantity Part No. Description
1 .....................1 .......................13870..........................Housing, Timer, 3200
2 .....................1 .......................14265..........................Clip, Spring
3 .....................3 .......................14087..........................Insulator
4 .....................1 .......................10896..........................Switch, Micro
5 .....................1 .......................15320..........................Switch, Micro, Timer
6 .....................2 .......................11413..........................Screw, Pan Hd Mach, 4-40 x 1-1/8
7 .....................1 .......................13886..........................Knob, 3200
8 .....................5 .......................13296..........................Screw, Hex Wsh, 6-20 x 1/2
9 .....................1 .......................11999..........................Label, Button
10 ...................1 .......................13018..........................Pinion, Idler
11 ...................1 .......................13312..........................Spring, Idler Shaft
12 ...................1 .......................13017..........................Gear, Idler
13 ...................1 .......................13164..........................Gear, Drive
14 ...................1 .......................13887..........................Plate, Motor Mounting
15 ...................1 .......................18743-1 ......................Motor, 120V, 60Hz, 1/30 RPM, 5600
.................................................19659-1 ......................Motor, 24V, 60Hz, 1/30 RPM
16 ...................2 .......................13278..........................Screw, Sltd Fillister Hd 6-32 x .156
17 ...................1 .......................15424..........................Spring, Detent, Timer
18 ...................1 .......................15066..........................Ball, 1/4”, Delrin
19 ...................1 .......................15465..........................Label, Caution
20 ...................1 .......................19210..........................Program Wheel Assy
21 ...................1 .......................13911..........................Gear, Main Driver, Timer
22 ...................17 .....................41754..........................Pin, Spring, 1/16 x 5/8 SS, Timer
23 ...................1 .......................13011..........................Arm, Cycle Actuator
24 ...................1 .......................13864..........................Ring, Skipper Wheel
25 ...................2 .......................13311..........................Spring, Detent, Timer
26 ...................2 .......................13300..........................Ball, 1/4”, SS
27 ...................1 .......................14381..........................Skipper Wheel Assy, 12 Day
.................................................14860..........................Skipper Wheel Assy, 7 Day
28 ...................1 .......................13014..........................Pointer, Regeneration
29 ...................1 .......................40096-24 ....................Dial, 12 AM Regen Assy, Black
.................................................40096-02 ....................Dial, 2 AM Regen Assy, Black
30 ...................1 .......................13881..........................Bracket, Hinger Timer
31 ...................2 .......................11384..........................Screw, Phil, 6-32 x 1/4 Zinc
32 ...................1 .......................13902..........................Harness, 3200
33 ...................2 .......................40422..........................Nut, Wire, Tan
34 ...................1 .......................15354-01 ....................Wire, Ground, 4”
35 ...................1 .......................14007..........................Label, Time of Day
For Service Assembly Numbers, See the Back of this Manual

Page 12
3210 Timer Assembly
For Service Assembly Numbers, See the Back of this Manual
61502-3210_REVA

Page 13
3210 Timer Assembly
For Service Assembly Numbers, See the Back of this Manual
Item No. Quantity Part No. Description
1 .....................1 .......................13870..........................Housing, Timer, 3200
2 .....................1 .......................13802..........................Gear, Cycle Actuator
3 .....................1 .......................40096-02 ....................Dial, 2 AM Regen Assy, Black
4 .....................1 .......................13886..........................Knob, 3200
5 .....................4 .......................13296..........................Screw, Hex Wsh, 6-20 x 1/2
6 .....................2 .......................11999..........................Label, Button
7 .....................1 .......................60405-15 ....................Program Wheel, w/34” Std Label, w/People Label Set @21
8 .....................1 .......................13806..........................Retainer, Program Wheel
9 .....................1 .......................13748..........................Screw, Flat Head St, 6-20 x 1/2
10 ...................1 .......................14265..........................Clip, Spring
11 ...................1 .......................15424..........................Spring, Detent, Timer
12 ...................1 .......................15066..........................Ball, 1/4” Delrin
13 ...................1 .......................13018..........................Pinion, Idler
14 ...................1 .......................13312..........................Spring, Ilder Shaft
15 ...................1 .......................13017..........................Gear, Idler
16 ...................1 .......................13164..........................Gear, Drive
17 ...................1 .......................13887..........................Plate, Motor Mounting
18 ...................1 .......................18743-1 ......................Motor, 120V, 60Hz 1/30 RPM, 5600
19 ...................1 .......................13278..........................Screw, Fillister Hd, 6-32 x .156
20 ...................1 .......................13830..........................Pinion, Program Wheel Drive
21 ...................1 .......................13831..........................Clutch, Drive Pinion
22 ...................1 .......................14276..........................Spring, Meter, Clutch
23 ...................1 .......................14253..........................Retainer, Clutch Spring
24 ...................3 .......................11384..........................Screw, Phil, 6-32 x 1/4
25 ...................1 .......................13881..........................Bracket, Hinge Timer
26 ...................3 .......................14087..........................Insulator
27 ...................1 .......................10896..........................Switch, Micro
28 ...................1 .......................15320..........................Switch, Micro, Timer
29 ...................2 .......................11413..........................Screw, Pan Hd Mach, 4-40 x 1-1/8
30 ...................1 .......................14198..........................Label, Indicator
31 ...................1 .......................15465..........................Label, Caution
32 ...................1 .......................14007..........................Label, Time of Day
33 ...................1 .......................14045..........................Label, Instruction
34 ...................1 .......................13902..........................Harness, 3200
35 ...................2 .......................40422..........................Nut, Wire, Tan
36 ...................1 .......................15354-01 ....................Wire, Ground, 4”
37 ...................1 .......................19210..........................Program Wheel Assy
38 ...................17 .....................41754..........................Pin, Spring, 1/16 x 5/8 SS Timer
39 ...................1 .......................13911..........................Gear, Main Drive, Timer
40 ...................1 .......................15354-01 ....................Wire, Ground 4”

Page 14
Powerhead Assembly (Designer)
For Service Assembly Numbers, See the Back of this Manual
61501_2510REVB

Page 15
Powerhead Assembly (Designer)
For Service Assembly Numbers, See the Back of this Manual
Item No. Quantity Part No. Description
1 .....................1 .......................40264..........................Backplate, SS/SVO, W-T-Screws
2 .....................1 ...........................................................3200, Timer 7 or 12 Day
3 .....................1 .......................11838..........................Power Cord
4 .....................1 .......................13547..........................Strain Relief
5 .....................1 .......................40400..........................Harness, Drive, Designer/Environmental
8 .....................2 .......................10231..........................Screw, Drive Mounting
9 .....................2 .......................10302..........................Insulator
10 ...................2 .......................10218..........................Switch
11 ...................1 .......................10909..........................Connecting Link Pin
12 ...................1 .......................10250..........................Retaining Ring
13 ...................1 .......................10621..........................Connecting Link
14 ...................1 .......................12576..........................Drive Cam, STF (Black)
.......................1 .......................12102..........................Drive Cam, RR (White)
15 ...................2 .......................10338..........................Roll Pin
16 ...................1 .......................13366..........................Drive Bearing
17 ...................2 .......................14923..........................Screw, Switch Mounting
18 ...................1 .......................41543* ........................Motor, Drive, 115V, 50/60Hz
.................................................42579**.......................Motor, Drive, 24VAC/VDC, 50/60Hz
.................................................41545* ........................Motor, Drive, 230V, 50/60Hz
20 ...................1 .......................12777..........................Brine Valve Cam, STF (Black)
.......................1 .......................10815..........................Brine Valve Cam, RR (White)
Not Shown:
.......................2 .......................10300..........................Screw, Timer Mounting
.......................1 .......................13741..........................Hole Plug
.......................1 .......................17904..........................Hole Plug
.......................2 .......................19367..........................Screw, Thumb
.......................1 .......................15441..........................Meter Cable Guide Assy (Econominder Only)
.......................1 .......................15495..........................Meter Cable,13.87” (Econominder Only)
.......................1 .......................60232-110...................Cover, Designer, 1 Pc, Black
* Bracket is integrated into the motor.
** Bracket is integrated into motor. Picture may not reflect component.

Page 16
For Service Assembly Numbers, See the Back of this Manual
Powerhead Assembly (Environmental)
Page 16

Page 17
For Service Assembly Numbers, See the Back of this Manual
Powerhead Assembly (Environmental)
Page 17
Item No. Quantity Part No. Description
1....................1 ......................18697-15 ....................Backplate, Hinged, 2900
2....................1 ..........................................................Timer: - 3200 7 Day
- 3200 12 Day
- 3210 Meter
3....................1 ......................11839..........................Power Cord, 12’ Fleck
4....................1 ......................13547..........................Strain Relief, Flat Cord
5....................1 ......................40400..........................Harness, Drive, Designer/Environmental
6....................1 ......................41543* ........................Motor, Drive, 115V, 50/60 Hz
...............................................42579**....................... Motor,
...............................................41545* ........................Motor,
7....................1 ......................60160-15 ....................Drive Cam Assy, STF, Blue, 2900
8....................2 ......................10338..........................Pin, Roll, 8/32 x 7/8
9....................2 ......................10231..........................Screw, Slot Hex, 1/4 - 20 x 1/2
10..................2 ......................10302..........................Insulator, Limit Switch
11 ..................2 ......................10218..........................Switch, Micro
12..................2 ......................14923..........................Screw, Pan Hd Mach, 4-40 x 1
13..................2 ......................12777..........................Cam, Shut-Off Valve
14..................1 ......................10909.......................... Pin, Link
Not Shown:
1 ......................15441.......................... Cable Guide Assy, 2750, 2510
1 ......................15495.......................... Meter Cable, 13.87”
1 ......................13741.......................... Plug, 3/4”, Knock-Out
1 ......................15806.......................... Plug, Hole, Heyco #2693
1 ......................16493.......................... Plug, Hole, Heyco
1 ......................17421.......................... Plug, 1.20 Hole Heyco #2733
2 ......................19691.......................... Plug, .750 Dia, Recessed, Black
7 ......................19800.......................... Plug, .140 Dia, White
4 ......................19801.......................... Plug, .190 Dia, White
2 ......................10300.......................... Screw, Slot Hex Wsh, 8-18 x 3/8
1 ......................10872.......................... Screw, Hex Wsh, 8-32 x 17/64
1 ......................60219-02 ....................Cover Assy, Environmental, Black w/Clear Window
* Bracket is integrated into the motor.
** Bracket is integrated into motor. Picture may not reflect component.

Page 18
Manual Powerhead Assembly
Item No. Quantity Part No. Description
1 ..................... 1.......................12593..........................Backplate, Manual
2 ..................... 1.......................12592..........................Bracket, Lever Position
3 ..................... 1.......................12596..........................Screw, Spec Mach, 1/4 - 20 x 1/2
4 ..................... 1.......................12707..........................Washer, Spring
6 ..................... 1.......................11235..........................Nut, Hex, 1/4 - 20, Mach Screw, Zinc
7 ..................... 1.......................12594..........................Lever, Valve Position
8 ..................... 2.......................10231..........................Screw, Slot Hex, 1/4 - 20 x 1/2 18-8 SS
9 ..................... 1.......................60224-32 ....................Cover Assy, Manual, Filter
....................... 1.......................60224-33 ....................Cover Assy, Manual, Softener
11 ................... 4.......................10300..........................Screw, Slot Hex Wsh, 8-18 x 3/8 Type “B” RC44-47
Not Shown:
....................... 1.......................10909..........................Pin, Link
For Service Assembly Numbers, See the Back of this Manual
60409REVA

Page 19
Notes

Page 20
Control Valve Assembly
For Service Assembly Numbers, See the Back of this Manual
22
23
25
2
15
6
13
9
12
8
11
1
24
5
18
19
17
30
20
29
21
10
4
3
14
16
7
26
27
61500_2510REVB