Pentair 9313C Series User manual

1
KEEP FOR FUTURE REFERENCE
pentair.com
INSTALLATION AND
OPERATION MANUAL
L-1588 Rev. B (12-09-19)
CENTRIFIGAL PUMPS
WITH FORCEFIELD TECHNOLOGY
9313C SERIES 9313S SERIES
EC REP
Pentair 375 5th Ave. NW, New Brighton, MN 55112 Phone: [phone] -OR- 800-424-9776 Fax: [phone] www.pentair.com
QNET BV Hommerterweg 286 6436 AM Amstenrade, The Netherlands KvK Zuid-Limburg 14091511
EU Authorized Representative:

2
Contents
EU Language Manuals ............................................................................................................................................................ 3
Introduction..............................................................................................................................................................................4
Description...........................................................................................................................................................................4
Intended Uses......................................................................................................................................................................4
Purpose of Manual..............................................................................................................................................................4
Misuses................................................................................................................................................................................5
 PumpIdentication..............................................................................................................................................................5
Pump Technical Data .............................................................................................................................................................. 6
 DimensionalSpecication...................................................................................................................................................6
 PumpSpecications............................................................................................................................................................7
Performance Charts............................................................................................................................................................8
Performance Charts............................................................................................................................................................9
Fluid Pumping Applications...............................................................................................................................................10
Tools..................................................................................................................................................................................10
Lifting, Transport, and Intermediate Storage................................................................................................................10
Assembly and Installation ..................................................................................................................................................... 11
Assembly...........................................................................................................................................................................11
Installation..........................................................................................................................................................................11
Control Systems .................................................................................................................................................... 14
Commissioning, Start-Up, Operation, Shut-Down ................................................................................................................ 15
Information.........................................................................................................................................................................15
Start-up, Operation, Shutdown..........................................................................................................................................15
MaintenanceandServicing...................................................................................................................................................17
 Information.........................................................................................................................................................................17
 Disposal.............................................................................................................................................................................17
 Cleaning.............................................................................................................................................................................17
 Maintenance,RoutineServicing,andInspection........................................................................................................17
Troubleshooting..............................................................................................................................................................18
Replacement Parts ................................................................................................................................................. 19
Model 9313 Part Illustrations and Repair Kits ..................................................................................................... 20
LimitedwwWarrantyon Hypro/ShuroAgriculturalPumps& Accessories..........................................................................................24

3
EU Languages
DO NOT attempt to install or operate your pump before reading the manual. Original copies of the manual for Hypro
pumpsareprovidedinEnglish.Tondacopyinyournativelanguage,gotowww.hypropumps.com.
Vor dem Ablesen des Handbuches versuchen Sie NICHT, Ihre Pumpe zu installieren. Originale des Handbuches fur
Hypro-PumpenwerdenaufenglischzurVerfugunggestellt.ZueineKopieinIhrerMuttersprachenden,zu
www.hypropumps.com zu gehen (German)
N’essayez pas d’installer votre pompe avant de lire le manuel. Des exemplaires originaux du manuel pour des pompes
de Hypro sont fournis en anglais. Pour trouver une copie dans votre langue maternelle pour aller a
www.hypropumps.com (French)
NON tentare di installare la vostra pompa prima di leggere il manuale. Esemplare originale del manuale per Hypro
pompe sono in inglese. Per trovare una copia nella vostra lingua andare a www.hypropumps.com (Italian)
Непытайтесьустановитьвашнасосдочтенияруководства.Оригинальныекопииэтогоруководствадлянасосы
Hyproнаанглийскомязыке.Найтикопиюнавашроднойязыкперейтикwww.hypropumps.com(Russian)
NO intente instalar su bomba antes de leer el manual. Copias originales del manual para Hypro se provee de bombas
en ingles. Para encontrar una copia en tu idioma nativo ir a www.hypropumps.com (Spanish)
NIEprobowaćinstalowaćpompyprzedjejodczytanieminstrukcji.OryginalnekopieinstrukcjiobsługipompHyprosą
dostarczanewjęzykuangielskim.Abyuzyskaćkopięwtwoimojczystymjęzykuprzejdźdowww.hypropumps.com
(Polish)
Takmayacalışmayınokumadanoncepompanınmanuel.OrijinalkopyalarınıHypropompalarıicinIngilizceolarak
sunulmuştur.Birkopyasınıbulmakicinyereldilgitwww.hypropumps.com(Turkish)
Nao tente instalar a bomba antes de ler o manual. As copias originais dos manuais para Hypro bombas sao
fornecidos em Ingles. Para encontrar uma copia em sua lingua nativa ir para www.hypropumps.com (Portuguese)
VERGEETNIETuwpompvoorhetlezenvanhethandboek.ExemplarenvandehandleidingvoorHypropompenzijn
beschikbaarinhetEngels.Opzoeknaareenexemplaarinuweigentaalganaarwww.hypropumps.com(Dutch)

4
Introduction
Description
Pentair’s Line of Hypro centrifugal pumps are designed for agricultural and industrial spraying and transfer of a variety of
uids:water,insecticides, herbicides, wettable powders, emulsives, liquid fertilizers, etc. Hypro Series 9313 hydraulic
motor-driven centrifugal pumps provide smooth performance. They can be conveniently mounted on the
tractor or sprayer, becoming part of the vehicle’s hydraulic system and freeing the PTO for other uses.
Intended Uses
Hyprocentrifugalpumpsareintendedforcreatingorboostingdynamicpressureinapproveduids.Hyprocentrifugal
pumps should never be used to pump liquids above 140°F (60°C), or below 34°F (1°C). For pumps equipped with
hydraulicmotors,thepumpshouldnotberunifthehydraulicoiltemperatureexceeds135°F(57°C).Anyusesoutside
ofthosespeciedinthismanualareconsideredmisusesandareprohibited.ContactPentairtechnicalservicewithany
questionsregardingspecicacceptableuses.
Purpose of Manual
Pentair has provided this manual to provide instructions and requirements that must be met when installing, using and
maintainingthepump(s)identiedonthecover.
If the product is sold, the seller must pass this manual onto the new owner.
The following special attention notices are used to notify and advise the user of this product of procedures that may be
dangerous to the user or result in damage to the product.
ATTENTION
Attention is used to notify of installation, operation, or maintenance information that is important but not safety related.
Thissymbolisusedtodenotethepresenceofanelectricalhazardthatwillresultinpersonalinjury,deathorproperty
damage.
Thissymbolisusedtodenotethepresenceofahazardthatwillresultinpersonalinjury,deathorpropertydamage.
California Proposition 65 Warning --Thisproductandrelatedaccessoriescontainchemicalsknowntothe
State of California to cause cancer, birth defects or other reproductive harm.

5
Misuses
Pentair’s line of Hypro centrifugal pumps are designed to operate effectively within the speed, pressure, and
environmental ranges speciedinthismanual.Operatingapumpoutsideoftheserangeswillvoidthewarrantyandcould
causedamagetoproperty,seriouspersonalinjury,ordeath.Youmustobservethefollowingsafetyguidelines:
• DO NOT run the pump faster than the maximum recommended speed
• DO NOT run the pump or hydraulic motor higher than the maximum recommended pressure
• DO NOT run pumps when the liquid has exceeded the maximum or minimum temperature limit (See Intended Uses)
• DO NOT pump non-approved liquids (See Fluid pumping Applications)
• DO NOT use pumps in explosive environments
• DO NOT pump water or other liquids intended for human consumption
• DO NOT operate a pump with a gasoline engine in an enclosed area
• DO NOTattachapipe,hoseorttingstothepumpthatisnotratedforthemaximumpressureofthepump(outlet)or
vacuum of the pump (inlet)
• DO NOToperateanyPentairpumpundertheinuenceofdrugsoralcohol
• DO NOT run a pump in reverse of its intended rotation
• DO NOT run the pump dry
Pump Identication
Pentair uses serialized labeling to enable users to precisely identify the pump’s manufacturing date.
Serial Number:
First and second digits: year (16 = 2016)
Third through fth digits: consecutive day of the year the pump was manufactured.
Sixth through tenth digits: unique pump serial number.

6
Pump Technical Data
9313C(S)-M04, -M05, -M05Y, -M08, -M08Y, M10, -M10Y, and -M16
Pump Dimensions
9313C-
9313S-
Motor Dim. Inch mm
(all)
A 9.44 240
B 8.76 223
C4.76 121
D 3.81 97
E 3.63 92
M04 F 11.52 293
M05,M05Y F11.57 294
M08,M08Y F11.77 299
M10,M10Y F 11.89 302
M16 F 12.27 312
(all)
G 5.50 140
H 5.25 133.4
I 2.63 66.7
J 1.60 41
øK 0.44 11.1
L 5.10 130
9313CU(SU)-M04, -M05, -M05Y, -M08, -M08Y, M10, and -M16
Pump Dimensions
9313CU-
9313SU
Motor Dim. Inch mm
(all)
A 9.34 237
B9.19 233
C 5.19 132
D 3.81 97
E 3.65 93
M04 F 11.41 290
M05,M05Y F 11.46 291
M08,M08Y F 11.66 296
M10 F 11.78 299
M16 F 12.16 309
(all)
G 5.39 137
H 5.25 133.4
I 2.63 66.7
J 1.60 41
øK 0.44 11.1
L 5.00 127
A
D
E
B
L
C
I
H
G
F
J
2X ØK
A
D
E
B
C
L
I
H
G
F
J
2X ØK

7
Pump Technical Data
9313C(S)-M04, -M05, -M05Y, -M08, -M08Y, M10, -M10Y, and -M16
Pump Dimensions
9313C-
9313S-
Motor Dim. Inch mm
(all)
A 9.44 240
B 8.76 223
C4.76 121
D 3.81 97
E 3.63 92
M04 F 11.52 293
M05,M05Y F11.57 294
M08,M08Y F11.77 299
M10,M10Y F 11.89 302
M16 F 12.27 312
(all)
G 5.50 140
H 5.25 133.4
I 2.63 66.7
J 1.60 41
øK 0.44 11.1
L 5.10 130
9313CU(SU)-M04, -M05, -M05Y, -M08, -M08Y, M10, and -M16
Pump Dimensions
9313CU-
9313SU
Motor Dim. Inch mm
(all)
A 9.34 237
B9.19 233
C 5.19 132
D 3.81 97
E 3.65 93
M04 F 11.41 290
M05,M05Y F 11.46 291
M08,M08Y F 11.66 296
M10 F 11.78 299
M16 F 12.16 309
(all)
G 5.39 137
H 5.25 133.4
I 2.63 66.7
J 1.60 41
øK 0.44 11.1
L 5.00 127
Pump Specications
Pump
Hydraulic
Motor
Inlet Max
PSI [BAR]
Hydraulic
Motor
Outlet Max
PSI [BAR]
Max
Flow
Rate
(GPM)
[LPM]
Max
Pressure
(PSI)
[BAR]
Max
Hyd.
Flow
(GPM)
[LPM]
Pump
Ports
Hydraulic
Ports
Dry
Weight
Mounting
Bolts
9313C-M04
3000[207] 100[6.9]
140[530] 90[6.2] 7[26.5]
1-1/2” NPT
Inlet
1-1/4” NPT
Outlet
SAE -8
Inlet
SAE -10
Outlet
40 lbs
[18kg]
2X 3/8”
OR M10
9313S-M04
9313C-M05 155[587] 100[6.9] 8[30.3]
9313S-M05
9313C-M08 188[712] 137[9.4] 13[49.2]
9313S-M08
9313C-M10 197[746] 150
[10.3] 16[60.6]
9313S-M10
9313C-M16 194[734] 103[7.1] 20[75.7]
9313S-M16
9313C-M05Y 155[587] 100[6.9] 8[30.3] SAE -8
Inlet
SAE -10
Outlet
SAE -6
Case Drain
9313S-M05Y
9313C-M08Y 188[712] 137[9.4] 13[49.2]
9313S-M08Y
9313S-M10Y 197[746] 150
[10.3] 16[60.6]
Pump
Hydraulic
Motor
Inlet
Max PSI
[BAR]
Hydraulic
Motor
Outlet
Max PSI
[BAR]
Max
Flow
Rate
(GPM)
[LPM]
Max
Pressure
(PSI)
[BAR]
Max
Hyd.
Flow
(GPM)
[LPM]
Pump
Ports
Hydraulic
Ports
Dry
Weight
Mounting
Bolts
9313CU-M04
3000
[207]
100[6.9]
140[530] 90[6.2] 7[26.5]
2” Universal
Flange Inlet
1-1/2”
Universal
Flange
Outlet
SAE -8 Inlet
SAE -10
Outlet
40 lbs
[18kg]
2X 3/8”
OR M10
9313SU-M04
9313CU-M05 155[587] 100[6.9] 8[30.3]
9313SU-M05
9313CU-M08 188[712] 137[9.4] 13[49.2]
9313SU-M08
9313CU-M10 197[746] 150
[10.3] 16[60.6]
9313SU-M10
9313CU-M16 194[734] 103[7.1] 20[75.7]
9313SU-M16
9313CU-M05Y 155[587] 100[6.9] 8[30.3] SAE -8 Inlet
SAE -10
Outlet
SAE -6
Case Drain
9313SU-M05Y
9313CU-M08Y
188[712] 137[9.4] 13[49.2]
9313SU-M08Y

8
Performance Charts
Allspecicationsandperformancedataarebasedonwaterasacarrieruid.
Note:Thedashedportionofthepumpcurvesisoutsidetherecommendedoperatingrange,andcanonlybeachieved
withsufcientNPSHa.RefertoInstallationInstructions.

9
Allspecicationsandperformancedataarebasedonwaterasacarrieruid.
Note:Thedashedportionofthepumpcurvesisoutsidetherecommendedoperatingrange,andcanonlybeachieved
withsufcientNPSHa.RefertoInstallationInstructions.

10
Fluid Pumping Applications
Application
Pump Materials Compatibility
Impeller Pump Housing
Noryl GTX Cast Iron Stainless Steel
Weed Control Chemicals X X X
Insect Control X X X
BrushControl X X X
Pest Control Chemicals and Fumigants X X X
Liquid Fertilizers X - X
Powdered Fertilizers X X X
Fluid Transfer X X X
Acids - - X
Flammable liquids, sewage, and clean water should never be pumped through a Hypro pump.
Hypropumpsarenotdesignedtobeusedascleanwaterpumpsasdenedin10CFRParts429and431.
Tools
Hypro 9313 Series centrifugal pumps and mounting assemblies are designed with metric fasteners.
Lifting, Transport, and Intermediate Storage
Packaging Descriptions and Unpacking Instructions
• Hypro centrifugal pumps are shipped in cardboard boxes for safe transporting.
• When pumps are shipped in large quantities, they may be put on a pallet to allow for easy storage, lifting and handling.
• Beforeliftinganypumporpallet,determinetheweightoftheitembylookingattheattachedpackingslipstoestablish
what lifting equipment should be used.
• Beforeinstallingthepump,determineifallthecomponentsarepresentandundamaged.Ifthepumpismissing
components, contact customer service immediately.
• Oncethepumpisunpacked,disposeofthepackaginginamannercompliantwithlocalandnationalregulations.
Lifting Instructions
• BeforeattemptingtoliftaHypropump,ensurethatthesurroundingworkingareaisfreeofhazardswhichcouldcause
injuryordamagetoproperty.
• Duringliftingoperations,anypersonnelnotinvolvedintheliftshouldnotentertheworkingarea.
• Ifliftinghooks,ropeorchainsarebeingusedforalift,theymustbefreeofdamageandberatedtocarry150%ofthe
weight of the load to be lifted.
• Always wear steel-toed shoes and cut-resistant gloves when attempting to lift.
• Whenliftingandcarrying,alwayskeepthepumpclosetoyourbody.(SeeFigure1)
• Whenstartingthelift,bendyourkneesandkeepyourbackstraight.(SeeFigure1)Tighteningthestomachmuscleswill
helpkeepyourbackstraight.
• Duringthelift,useyourlegstodothework.Neveruseyourback,andmakesureyourlegsareatleastshoulder-width
apart. (See Figure 1)