Pentair PANTERA ECO User manual

L300318_PanteraEco_A4_Owners_Manual_FA.indd 1L300318_PanteraEco_A4_Owners_Manual_FA.indd 1 14/09/2020 1:48:08 PM14/09/2020 1:48:08 PM

L300318_PanteraEco_A4_Owners_Manual_FA.indd 2L300318_PanteraEco_A4_Owners_Manual_FA.indd 2 14/09/2020 1:48:08 PM14/09/2020 1:48:08 PM

L300318_PanteraEco_A4_Owners_Manual_FA.indd 3L300318_PanteraEco_A4_Owners_Manual_FA.indd 3 14/09/2020 1:48:09 PM14/09/2020 1:48:09 PM

L300318_PanteraEco_A4_Owners_Manual_FA.indd 4L300318_PanteraEco_A4_Owners_Manual_FA.indd 4 14/09/2020 1:48:09 PM14/09/2020 1:48:09 PM

L300318_PanteraEco_A4_Owners_Manual_FA.indd 5L300318_PanteraEco_A4_Owners_Manual_FA.indd 5 14/09/2020 1:48:09 PM14/09/2020 1:48:09 PM

278 248
281
605
275
450
102
180
121
183
PANTERA 800 VS
A A
B B
C C
D D
E E
F F
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
0
2
4
6
8
10
12
14
16
18
0 50 100 150 200 250 300 350 40
0
Head (m)
Flow (LPM)
Pantera Eco
2850 RPM
2400 RPM
2000 RPM
1600 RPM
1450 RPM
L300318_PanteraEco_A4_Owners_Manual_FA.indd 6L300318_PanteraEco_A4_Owners_Manual_FA.indd 6 14/09/2020 1:48:10 PM14/09/2020 1:48:10 PM

L300318_PanteraEco_A4_Owners_Manual_FA.indd 7L300318_PanteraEco_A4_Owners_Manual_FA.indd 7 14/09/2020 1:48:10 PM14/09/2020 1:48:10 PM

L300318_PanteraEco_A4_Owners_Manual_FA.indd 8L300318_PanteraEco_A4_Owners_Manual_FA.indd 8 14/09/2020 1:48:10 PM14/09/2020 1:48:10 PM

L300318_PanteraEco_A4_Owners_Manual_FA.indd 9L300318_PanteraEco_A4_Owners_Manual_FA.indd 9 14/09/2020 1:48:10 PM14/09/2020 1:48:10 PM

L300318_PanteraEco_A4_Owners_Manual_FA.indd 10L300318_PanteraEco_A4_Owners_Manual_FA.indd 10 14/09/2020 1:48:10 PM14/09/2020 1:48:10 PM

Press for low speed Press for medium
speed Press for high speed
1450RPM 2400RPM 2850RPM
• Filtration and water
circulation.
• Cleaning with a
suction cleaner.
• Backwashing lter.
• Operating some
water features such
as jets or waterfalls.
• Solar heating
1.
Press and hold button corresponding to speed
you wish to change. Hold for 3 seconds and a
light should begin to flash.
2.
To decrease speed by 50rpm increments with
1000rpm as the minimum limit.
To increase speed by 50rpm increments with
2850rpm as the maximum limit.
3.
To save the current speed setting and return to
normal operation mode.
Will cancel the change and revert back to the
original speed and return to normal operation
mode.
Holding all 3 buttons for 3 seconds will reset the
speeds to default.
+
,
+
or
L300318_PanteraEco_A4_Owners_Manual_FA.indd 11L300318_PanteraEco_A4_Owners_Manual_FA.indd 11 14/09/2020 1:48:10 PM14/09/2020 1:48:10 PM

Disable or Enable the
Prime Time
Press the “STOP” button for 5 seconds to
DISABLE/ENABLE prime time. (The power LED/
Green will light up and not blink when prime
time is disabled), this function will be back to
default when reset to default or press again this
button for 5 seconds.
Pressing any two of the speed buttons
simultaneously to finish priming time as
temporarily.
Priming time and Priming speed setup
Pressing the “STOP” button for 10 seconds the
power LED/ green will blink twice in every one
second then display will show “P 2” and ready to
adjust time (Limit time to 240min maximum and
minimum for 1Min).
Pressing the button ”low” will lower the time by
1 min step (Holding for 2 seconds to decrease
time continuously).
Pressing the button “high” (will rise the time by
1 min step (Holding for 2 seconds to increase
time continuously).
Pressing the button “med/set” will save the new
time then automatic go to Priming speed setup
in next step and display show “2850” and ready
to adjust speed.
Pressing the button “low” will lower the speed by
25 RPM step (Holding for 2 seconds to decrease
speed continuously).
Pressing the button “med/set” will save.
, or
L300318_PanteraEco_A4_Owners_Manual_FA.indd 12L300318_PanteraEco_A4_Owners_Manual_FA.indd 12 14/09/2020 1:48:10 PM14/09/2020 1:48:10 PM

FREQUENCY
Once per week Once per month
CHECK
Inspect trap basket, and empty
of any leaves and other debris.
Leaves and other debris that
collects in basket will choke
off water ow through the
pump and reduce eciency
and performance. See below
instructions on cleaning the trap.
Check the pump to ensure no
water is leaking from inlet and
outlet joints, whilst pump is
operating. If leaks are noticed,
clean and grease the o-rings or
replace if necessary.
Clean area around pump and
ensure there are no leaves or
debris which could become a re
hazard or choke the motor fan.
Check that there are no leaks
from under the pump. If there are,
this could be a sign of a leaking
mechanical seal. Call a Pentair
Service Agent immediately, to
prevent damage to the motor.
Check pump and motor for
insects and pest infestations
and ensure that motor ns are
clean of dust and dirt. Clean if
necessary.
L300318_PanteraEco_A4_Owners_Manual_FA.indd 13L300318_PanteraEco_A4_Owners_Manual_FA.indd 13 14/09/2020 1:48:11 PM14/09/2020 1:48:11 PM

SYMPTOM CAUSE REMEDY
Low water
pressure, low ow
from pump.
Suction leaks / lost
prime.
• Pump must be primed; make sure that the
pump casing and strainer are full of water.
Refer priming instructions.
• Make sure there are no leaks in suction
piping and ensure all o-rings are present
and clean.
• Make sure suctions pipe inlet is well below
the water level to prevent pump from
sucking air.
• Suction lift of 3 to 6 metres will reduce
performance. Suction lift of more than 6
metres will prevent pumping and cause
pump to lose prime. In either instance,
move the pump closer (vertically) to water
source. Ensure that the suction pipe
diameter is large enough.
Low speed setting. • Check speed setting. Refer to speed
selection section of this manual. Reset to
default if necessary.
Clogged pipe /
strainer / impeller /
lter system.
• Ensure trap is not clogged with debris;
clean basket and/or filter.
• Make sure that the impeller is not
clogged. This should be checked by
qualified personnel only.
• Pump may be trying to push too high a
column of water. If so, a higher pressure
pump is required.
L300318_PanteraEco_A4_Owners_Manual_FA.indd 14L300318_PanteraEco_A4_Owners_Manual_FA.indd 14 14/09/2020 1:48:11 PM14/09/2020 1:48:11 PM

SYMPTOM CAUSE REMEDY
No water coming
from pump (pump is
working).
Air ingress to
system.
• Prime the pump. Check that there are no
air leaks in the suction piping or ttings.
Ensure the strainer lid is airtight and
tted securely. Ensure all o-rings are
present.
Pump does not
work.
Motor fault. • Refer to motor fault codes.
No power at outlet. • Use another electrical appliance that is
known to work to check power outlet.
Blown fuse / Circuit
breaker.
• Check and call electrician if necessary.
Pump running too
slow.
Low speed setting. • Check speed setting. Refer to speed
selection section of this manual. Reset to
default if necessary.
Motor high
temperature limit
exceeded.
• Ensure motor fins are clean and fan is
intact and free from blockages. Ensure
adequate ventilation and reduce ambient
temperature.
Water leaking from
between the casing
and motor.
Casing bolts are
not tightened
suciently; worn
mechanical seal
requires replacing.
• Switch off the power to the pump.
Tighten the casing bolts or replace the
mechanical seal as required.
L300318_PanteraEco_A4_Owners_Manual_FA.indd 15L300318_PanteraEco_A4_Owners_Manual_FA.indd 15 14/09/2020 1:48:11 PM14/09/2020 1:48:11 PM

MOTOR FAULT CODE
E01 E02 E03 E04 E05 E06 E07 E08
Micro-
controller
failure
Mains under
voltage
Over Temp. Over
Current
Mains over
voltage
Output
shaft seized
Self check
failed
Motor fault
Microcon-
troller is
continually
rebooting.
The mains
voltage has
dropped
below
180VAC.
Motor
temp. has
exceeded
max. limit.
Speed will
reduce
until motor
returns to
acceptable
temp.
Over
current
protection
has tripped.
Speed will
reduce until
motor
returns to
acceptable
condition.
The mains
voltage
has risen
to above
269VAC.
Motor shaft
seized due
to blockage
in pump or
fan.
One or more
of the self-
tests failed
during start
up or while
running.
One or
more of the
phases has
become
D/C.
L300318_PanteraEco_A4_Owners_Manual_FA.indd 16L300318_PanteraEco_A4_Owners_Manual_FA.indd 16 14/09/2020 1:48:11 PM14/09/2020 1:48:11 PM

12
11
14
13
15
10
9
8
6
7
3
16
1
4
17
5
2
18
PPP 800 VS
ITEM NO.
PART NUMBER
Description
1 412050
YOKE - PANTERA SUB-ASSEMBLY
2
M8
NUT 5/16inW HEX ST/ST
3 702770
SCREW 5/16inW x 3/4in HWF S/S
4 505070
SHAFT SLEEVE
5
BS-016
O-RING BS106
6 702206
ORING 400 600 700 900 CASING
( BS258 )
7 305300
BAFFLE - MOULDED
8 700270
MECHANICAL SEAL
9 305460
DIFFUSER MOULDED
10 507650
IMPELLER
11 801200
CASING PANTERA POOL
12 408730
BAFFLE
13 504605
PRIMING CAP
14
M8 x 45
Bolt 5/16 in W x 1.75 in HWF
15
M8 x 55
Bolt 5/16 in W x 2.25 in HWF
16 702509
PANTERA POOL PUMPS
17
C35-43
MOTOR PAD 160x12x10 Rx
EPDM50SH
18 190001
MOTOR
A A
B B
C C
D D
E E
F F
8 8
7 7
6 6
5 5
4 4
3 3
2 2
1 1
L300318_PanteraEco_A4_Owners_Manual_FA.indd 17L300318_PanteraEco_A4_Owners_Manual_FA.indd 17 14/09/2020 1:48:11 PM14/09/2020 1:48:11 PM

Item No. Part Number Description
1412050 Yoke & lip seal assembly
2See Fasteners Kit Nut 5/16inw hex st/st
3See Fasteners Kit Screw 5/16inw x 3/4in hwf s/s
4See Seal Kit Shaft sleeve
5See Seal Kit O-ring bs106
6702206K Oring 400 600 700 900 casing ( bs258 )
7305300 Bae - moulded
8 800583K Seal kit
9305460K Diffuser moulded
10 507530K Impeller
11 801200K Casing pantera pool
12 800897K Lid & o-ring kit
13 504605 Priming cap
14 See Fasteners Kit Bolt 5/16 in w x 1.75 In hwf
15 See Fasteners Kit Bolt 5/16 in w x 2.25 In hwf
16 702509 Base
17 See Base Motor pad 160x12x10 rx epdm50sh
18 801301 Motor
Not Shown
302310 Strainer Basket
801498 Control cover
800042 PCB Replacement
L300318_PanteraEco_A4_Owners_Manual_FA.indd 18L300318_PanteraEco_A4_Owners_Manual_FA.indd 18 14/09/2020 1:48:11 PM14/09/2020 1:48:11 PM

PURCHASED FROM:
PURCHASE DATE:
SERIAL NO:
MODEL NO:
L300318_PanteraEco_A4_Owners_Manual_FA.indd 19L300318_PanteraEco_A4_Owners_Manual_FA.indd 19 14/09/2020 1:48:11 PM14/09/2020 1:48:11 PM

L300318_PanteraEco_A4_Owners_Manual_FA.indd 20L300318_PanteraEco_A4_Owners_Manual_FA.indd 20 14/09/2020 1:48:11 PM14/09/2020 1:48:11 PM