Pepperl+Fuchs HiC2832R1 User manual

Release date 2015-03-11 15:40 Date of issue 2015-03-11 230983_eng.xml
HiC2832R1
1
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
Pepperl+Fuchs Group USA: [phone] Singapore: [phone]Germany: [phone]
www.pepperl-fuchs.com [email protected].com [email protected].com [email protected]
Switch Amplifier
Zone 0, 1, 2
HiC2832R1
Termination Board
II
10a
9a
12
15
24V DC
FAULT
1a, 1b
2a, 2b
6b
5a
5b
1
4
-
+
+
-
+
-
SL2
I
1a
1b
2
5
+
-
8a
SL1
7a
11
14
+
-
10 kΩ
1.5 kΩ
I
II
10 kΩ
1.5 kΩ
Connection
Assembly
• 2-channel isolated barrier
• 24 V DC supply (bus powered)
• Dry contact or NAMUR inputs
• Application-specific outputs
• 2 passive transistor outputs (resistive)
• Line fault transparency (LFT)
• Up to SIL2 acc. to IEC 61508
Function
This isolated barrier is used for intrinsic safety applications.
The device transfers digital signals (NAMUR sensors or dry
contacts) from a hazardous area to a safe area.
Each input controls a passive transistor output with a resistive
output characteristic.
The outputs have three defined states: 1-Signal = 6.5 V
voltage drop, 0-Signal = 33 kΩand 6.5 V voltage drop and
fault > 100 kΩ.
This output characteristic offers line fault transparency on the
signal lines.
Switches allow to reverse the output mode of operation and to
disable the line fault detection of the field circuit.
This device mounts on a HiC Termination Board.
Application
This device is compatible to the control:
• Yokogawa ProSafe DI card SDV144
Compatibility check to other ESD/DCS systems on request.
2
Features
PWR
HiC
2832
R1
2 ch
Switch
Amplifier
CH1
CH2
STATUS/
FAU LT
LED green:
Power supply
Front view
LED yellow/red:
Status output/
Fault channel 1
LED yellow/red:
Status output/
Fault channel 2
Place for
labeling
Switch 1 ... 4

Release date 2015-03-11 15:40 Date of issue 2015-03-11 230983_eng.xml
Technical data HiC2832R1
2
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
Pepperl+Fuchs Group USA: [phone] Singapore: [phone]Germany: [phone]
www.pepperl-fuchs.com [email protected].com [email protected].com [email protected]
General specifications
Signal type Digital Input
Supply
Connection SL1: 1a(-), 1b(-); 2a(+), 2b(+)
Rated voltage Un19 ... 30 V DC via Termination Board
Ripple ≤10 %
Rated current In≤30 mA
Power loss ≤600 mW
Power consumption ≤700 mW
Input
Connection SL2: 5a(+), 5b(-); 1a(+), 1b(-)
Rated values acc. to EN 60947-5-6 (NAMUR), see system description for electrical data
Open circuit voltage/short-circuit current approx. 10 V DC / approx. 8 mA
Switching point/switching hysteresis 1.2 ... 2.1 mA / approx. 0.2 mA
Line fault detection breakage I ≤0.1 mA , short-circuit I ≥6.5 mA
Pulse/Pause ratio ≥100 µs / ≥100 µs
Output
Connection SL1: 8a(+), 7a(-); 10a(+), 9a(-)
Rated voltage Un19 ... 30 V DC with external resistance > 2 kΩ, e. g. 16-channel ProSafe DI card SDV144 from Yokogawa
Response time ≤200 µs
Output I, II signal or error message, passive transistor output (resistive)
0-signal: 33 kΩ± 5 % + voltage drop 6.5 V ± 0.5 V
1-signal: voltage drop 6.5 V ± 0.5 V
fault: > 100 kΩ
Error message output
Connection SL1: 6b
Output type open collector transistor (internal fault bus)
Transfer characteristics
Switching frequency ≤5 kHz
Electrical isolation
Output/power supply basic insulation according to IEC 61010-1, rated insulation voltage 60 Veff
Output/Output basic insulation according to IEC 61010-1, rated insulation voltage 60 Veff
Directive conformity
Electromagnetic compatibility
Directive 2004/108/EC EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility NE 21:2006
For further information see system description.
Degree of protection IEC 60529:2001
Protection against electrical shock IEC 61010-1
Ambient conditions
Ambient temperature -20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection IP20
Mass approx. 100 g
Dimensions 12.5 x 128 x 106 mm (0.5 x 5.1 x 4.2 in)
Mounting on Termination Board
Coding pin 1 and 2 trimmed
For further information see system description.
Data for application in connection
with Ex-areas
EC-Type Examination Certificate BVS 11 ATEX E 026
Group, category, type of protection ¬II (1) G [Ex ia] IIC, II (1) D [Ex ia] IIIC
¬I (M1) [Ex ia] I
Input Ex ia
Voltage Uo10.5 V
Current Io17.1 mA
Power Po45 mW (linear characteristic)
Supply
Maximum safe voltage Um253 V AC (Attention! Umis no rated voltage.)
Output
Maximum safe voltage Um253 V AC (Attention! Umis no rated voltage.)
Electrical isolation
Input/Output safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Input/power supply safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V
Directive conformity

Release date 2015-03-11 15:40 Date of issue 2015-03-11 230983_eng.xml
Technical data HiC2832R1
3
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
Pepperl+Fuchs Group USA: [phone] Singapore: [phone]Germany: [phone]
www.pepperl-fuchs.com [email protected].com [email protected].com [email protected]
Configure the device in the following way:
• Push the red Quick Lok Bars on each side of the device in the upper position.
• Remove the device from Termination Board.
• Set the DIP switches according to the figure.
Directive 94/9/EC EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-26:2007 , EN 50303:2000
International approvals
UL approval
Control drawing 116-0331
IECEx approval IECEx BVS 11.0040
Approved for [Ex ia Ga] IIC, [Ex ia] IIIC , [Ex ia] I
General information
Supplementary information EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of
Conformity and instructions have to be observed where applicable. For information see www.pepperl-
fuchs.com.
The pins for this device are trimmed to polarize it according to its safety parameter. Do not change!
For further information see system description.
Configuration
Refer to the Instruction
Manual to install and
operate the unit
CAUTION
Inverted
Input to output operation
Function
I
S1
CH1
Switch settings
Input fault detection
Fault enable
Fault disable
Normal
S2
I
II
II
I
S3
CH2
S4
I
II
II
S1 S4
I
II
S1 S4
I
II
Switch settings
S Channel Function Position
1I Mode of operation Inverted I
Normal II
2I Input line fault
detection
ON I
OFF II
3II Mode of operation Inverted I
Normal II
4II Input line fault
detection
ON I
OFF II
Trip points
10 kΩ10 kΩ
< 0.15 mA
< 1.4 mA
> 1.85 mA
> 0.28 mA
> 5.8 mA
~9.6 V
< 0.1 mA
1.5 kΩ1.5 kΩ
0 V
mA
U
I
SC
Input
Outputs
(24 V, 4 kΩ)
Normal operation,
Fault detection enabled
LED Status/Fault
LB
~ Usupply
-6.5 V
~0.45