Perfect Prime 530 User manual

LIGHT METER
530
Instruction Manual

CONTENTS
P. 1
................................................................ 2
......................................................................... 3
....................................................... 4
......................................................................... 4
....................................................................... 5
...................................................................... 6
.............................................. 7 - 11
........................ 12
1. Safety Information
2. Introduction
3. Precautions On Handling
4. Maintenance
5. Specifications
6. Symbol Definition And Button Location
6.1 LCD Display
6.2 Name Of Parts & Position
7. Characteristics Of Sensor Spectrum Response

1. SAFETY INFORMATION
P. 2
Read the following safety information carefully before attempting to
operate or service the meter.
Use the meter only as specied in this manual ; otherwise, the protection
provided by the meter may be impaired.
ENVIRONMENT CONDITIONS:
•Altitude up to 2000 meters
•Relatively humidity 90% max.
•Operation Ambient 0 ~ 40°C
EXPLANATION OF SYMBOLS:
Comply with EMC.
When servicing, use only specied replacement parts.

Thank you for using our Light Meter. To ensure that you can get the most
from it, we recommend that you read and follow the manual carefully
before use. The Light Meter has been designed, manufactured, and
delivered under strict quality control criteria by a factory certied. This
meter has the following characteristic.
• Easy to use
• Automatic zero
• Automatic ranging
• MAX/MIN function
• Large backlight LCD
display
2. INTRODUCTION
P. 3

Operating carefully, and do not drop the meter or hit it with a hard object.
Avoid using the meter in a dirty, dusty, or salt-air area or where there are
corrosive gases. If dirt or dust adhered to the surface of the detecting
light, will decrease accuracy of the measuring value to clean the surface
by wiping with a soft and dry cloth.
3. PRECAUTIONS ON HANDLING
4. MAINTENANCE
3. PRECAUTIONS ON HANDLINGE
4. MAINTENANCE
ATTENTION!
Repairs or servicing not covered in this manual should only be
performed by qualied personal.
CLEANING
Periodically wipe the case with a dry cloth. Do not use abrasives or
solvents on this instrument.
Note:
If it is not used for a long time, please store the meter in
chamber under 60%RH.
P. 4

5. SPECIFICATIONS
P. 5
Measuring level range
Resolution:
Accuracy:
Angle deviation from
cosine characteristics:
Temperature characteristics:
Response time:
Light detector:
Over range:
Power supply:
Power life:
Operation temperature:
Operation humidity
Storage Temperature:
Storage Humidity:
Dimension / Weight:
Weight:
Accessories:
[Note] 1fc =10.76lx
0.0 to 199.9/1999/19990/199900 lx
0.0 to 19.9/199.9/1999/19990fc
Automatic or manual selection of range
0.1 ~ 100 lx, 0.1 ~ 10 fc
±3% (Calibrated to standard incandescent lamp 2856°K)
8% other visible light source
10° ± 1% 30° ± 2%
60° ± 5% 80° ± 20%
±0.1% / °C(25°C)
0.5 sec
SI Photodiode
“-OL-” display
1.5V type AA battery x2
Approx. 80 hours
0°C ~ 40°C(32°F ~ 104°F)
0~80% RH
-10 to 50°C (14 to 122°F)
0 to 60% RH
169(L)×63(W)×37(H)mm (6.7”×2.5”×1.5”)
Approx. 185g
Battery, instruction manual, carrying case.

6. SYMBOL DEFINITION AND
BUTTON LOCATION
P. 6
6.1 LCD Display:
Minimum value
indicator
Maximum value
indicator
Value hold
indicator
Measuring value
Unit indicator
Range indicator
Autopower
o indicator
Battery
capacity
indicator

6. SYMBOL DEFINITION AND
BUTTON LOCATION
P. 7
6.2 Name of Parts & Position
* Operation:
Press the power button to turn on the power. Notice that covering the
light-detecting surface with the cap.“CAP-“ will auto-appear on the LCD
display. After “CAL-” appears, the meter enters the automatic zero
adjustment. When automatic zero adjustment is completed,“CAL-”
disappears and “0.0” appears. After conrming the “0.0” display, remove
the cap to start measuring. After the measurement has been completed,
press the power button again to turn o the power, and cover the
light-detecting surface with the cap for protecting against stray light.

6. SYMBOL DEFINITION AND
BUTTON LOCATION
P. 8
Note:
If “ERR1” appears, check the cap to make sure it is on properly
1Sensor Cap :
This parts is to protect the
sensor from scratching and
c reate complete dar k
environment for the meter
to perform dark current
calibration. During power
on process, this cover
should be set properly on
the sensor otherwise an
error message will be
shown on the LCD.
2Light Sensing Probe:
•This probe can be rotated various angles to the LCD surface to suit the
measuring requirement.

6. SYMBOL DEFINITION AND
BUTTON LOCATION
P. 9
•It can be also detached from the
meter to measure in distance,
which createsmore exibility.
6 1/2" large size back light
LCD display.
LCD display:3
Press button to turn on the meter and it will automatically turn itself
o 30 minutes after its last key operation. The user may disable this
automatic power o function by pressing and holding“ ” button while
powering on. The “ ” symbol will disappear to conrm this operation.
Press button again to turn the meter o.
Power button:4
Press button to set the meter working under MAX/MIN mode. By
pressing button, the user may swap the LCD reading among
maximum, minimum and current reading. Press and hold button for 3
seconds to exit Max/Min mode.
Max Min button:5

6. SYMBOL DEFINITION AND
BUTTON LOCATION
P.10
The user may hold the present reading and keep it on the LCD display by
pressing the button. To release the held data operation, press the
button again.
HOLD button:6
The user may use the button to select the preferred measuring
range or automatically selected by the meter.
The available ranges are:
AUTO, 200, 2000, 20000, 200000 lx
AUTO, 20, 200, 2000, 20000 fc
Range selector button:7
Press button to switch the measuring unit between Foot Candle and
Lux.
Fc/lx selector button:8
Press button to turn on the LCD back light and it will be automatically
o after 30 seconds.
Backlight button:9

P.11
6. SYMBOL DEFINITION AND
BUTTON LOCATION
When battery capacity segment is less than one, the user should replace
the battery. The battery cabinet cover can be opened with a Philips screw
driver and two AA type batteries should be installed.
Battery cabinet cover:10

P.12
7. CHARACTERISTICS OF SENSOR
SPECTRUM RESPONSE

CUSTOMER SERVICE INQUIRIES
Your emails are important to us so we strive to reply all
inquiries and emails within 24 hours. In exceptional cases,
we may require more time to respond.
Thank you for your understanding.
For more information about our products and services,
please send us an email:
[email protected]
For B2B or project-based application, please send an email:
[email protected]
FOR MORE INFORMATION ABOUT PERFECTPRIME PLEASE VISIT
OUR ABOUT US PAGE AND FEEL FREE TO BROWSE.
Scan QR Code for the Product
Manual page (Multi-Language
available for certain products)
Scan QR Code for the Youtube
channel for video manual
Scan QR Code to register the
product for 1 year warranty

Tyche Smart Limited
[email protected]
2nd Floor, 107 Charterhouse Street,
EC1M 6HW, London,
England UNITED KINGDOM
[phone]
Retailer
Email
Address
Telephone