Perfect Prime AQ380 User manual

MULTI IAQ MONITOR
AQ380
Instruction Manual

CONTENTS
P. 1
........................................................................ 2
........................................................................ 2
............................................................. 3
..................................................... 4
.......................................... 5
.................................................................... 6 - 13
............................................. 14 - 18
.................................................... 19
............................................................ 19
1. APPLICATION
2. ACCESSORIES
3. SAFETY PRECAUTION
4. INSTRUMENT DESCRIPTION
4.1 FEATURE AND FUNCTION
4.2 INDICATION ON THE LCD DISPLAY
5. OPERATION
6. GENERAL SPECIFICATIONS
7. MAINTENANCE OR REPAIR
8. PRODUCT DISPOSAL

1. APPLICATION
2. ACCESSORIES
P. 2
This air quality meter can measure and display CO2, PM2.5, Humidity
and Temperature measurements and is ideal for monitoring indoor air
quality in a variety of environments.
1. APPLICATION
1Meter (with a 3.7V Rechargeable lithium battery)
1User’s Manual
1Micro USB cable
2. ACCESSORIES

• Do not operate in environments with ammable gas or humid
environments.
•Operating altitude: up to 2000M.
•Operating environment: Indoor use; Pollution degree 2.
•Clean with soft cloth when dirty, such as glasses cloth. Do not clean
with chemicals and other solvents.
•EMC: EN61326-1:CISPR 11:Group 1, Class B
○Class B – Equipment for use in all establishments other than
domestic.
○Group 1 – RF energy generated is needed for internal functioning.
3. SAFETY PRECAUTION
P. 3
Caution! Please refer to this manual.
Improper use may damage the meter
and its components.
Complies with European Directive.

4. INSTRUMENT DESCRIPTION
4.1 FEATURE AND FUNCTION
P. 4
1. LCD
2. Right-side button
3. Memory reading / Up button
4. MAX / MIN / AVG button
5. Power button
6. Single log and auto-record
button/Down button
7. Temperature and humidity
sensing port
8. Air outlet for sensor
9. Air inlet for sensor
10. Micro USB jack

4.2 INDICATION ON THE LCD DISPLAY
4. INSTRUMENT DESCRIPTION
P. 5
1. MAX / MIN /AVG /MAN MIN
2. Manual recording
3. Auto-recording
4. Read record
5. Battery indicator
6. Auto-power o
7. Buzzer
8. Alarm
9. CO2
10. PM2.5
11. Temperature
12. MM minute, SS second
13. PM10
14. Humidity

Please hold the meter in the following way for the correct measured value:
The placement follows the
electrical specications described
in Section 7.
This is a suitable way to hold the
meter, holding for a long time
may aect the accuracy.
This is not a proper way to hold
the meter, it will block the
temperature and humidity
sensors.
This is not a proper way to hold
the meter, it will block the PM2.5,
PM10 and CO2 sensors.
5. OPERATION
P. 6

5. OPERATION
P. 7
5.1 Power on/off
Press to turn the power on or o.
5.2 Auto Power Off
At the power-on status, press and hold for more than 2 seconds to
disable or resume auto power o function. When auto power o is
activated, the indicator appearing, and it will automatically turn o
after 30 minutes.
5.3 Backlight mode
Press“right-side button”to turn on or o the backlight. (When the red
backlight for alarm is on, this button is invalid) The backlight mode is
turned o automatically after 15 seconds.
5.4 MAX/MIN AVG and MAN MIN
Press to enter this function, the MAX is shown on the screen and it
displays the maximum value.
Press repeatedly to select the function of MIN/AVG/MAX MIN/MAX
and update the displayed value. When select MAX MIN function, it
displays the current measured value.
5.5 REC Manual record
Press to save one data log, the “REC”and the log number appear on
the LCD for one second. For an example of the log number 10, it will
increase by 1 when pressing every time. When reaching the
maximum log number 20, appears.

5. OPERATION
P. 8
5.6 LOG starts the auto-recording function
Press and hold for more than 2 seconds, “LOG” appears on the LCD,
and auto-recording starts. If the power is insucient during auto-record-
ing, appearing, auto-recording will be forcibly stopped. When
reaching themaximum log number 20, appears.
Press and hold again for more than 2 seconds to exit the
auto-recording function.
5.7 Read the data recorded in the memory
Press to enter the memory-reading mode, while and the log
number appear on the LCD for one second, the record is then displayed.
Read the data recorded in the memory with or .
Press and hold to exit this mode.
5.9 Clear memory
At the shutdown status, press and hold and then press to turn
on the meter, the and software version appears successively on the
LCD, release the to clear the memory.
5.8 °C or °F units
At the shutdown status, press and hold , then press to turn on
the meter, after the software version appears, release .
Repeat the above steps to switch the unit.

• Auto-shutdown: OFF
• Key sound: On
•The calibration value resumed to 0
•CO2 Abc OFF
•Memory cleared
P. 9
5. OPERATION
5.10 Turn on / off the key sound
The sound is defaulted as on and the is displayed. At the shutdown
status, press and hold and then press to turn on the meter, after
the software version appears, release and the disappears, the
key sound is o.
Repeat the above step to tun on the key sound.
5.11 Resume the factory settings
At the shutdown status, press and hold “right-side button”and then press,
the and software version appears successively on the LCD,
release the“right-side button”to complete the process of resuming to the
factory settings and clearing the memory.
5.12 Function settings
Press“right-side button”for more than 2 seconds to enter the setting
mode.
Press the“right-side button”repeatedly to enter the setting function
1 ~ 8 in sequence:

5. OPERATION
P.10
SET 1. Time interval setting
1. The LCD displays:
2. Press or to select the interval 5 seconds / 10 seconds /
5 minutes / 10 minutes / 20 minutes / 30 minutes / 60 minutes;
the default value is 5 seconds.
3. Press the“right-side button”again to enter set 2.
SET 2. CO2 alarm setting
1. The LCD displays:
2. Press to move the digit, and the selected digit will ash.
3. Press or to increase or decrease the CO2 value.
4. Press the“right-side button”again to enter set 3.

P.11
SET 3. PM2.5 alarm setting
1. The LCD displays:
2. Press to move the digit, and the selected digit will ash.
3. Press or to increase or decrease the CO2 value.
4. Press the“right-side button”again to enter set 4.
5. OPERATION
SET 4. PM10 alarm setting
1. The LCD displays:
2. Press to move the digit, and the selected digit will ash.
3. Press or to increase or decrease the CO2 value.
4. Press the“right-side button”again to enter set 5.

P.12
SET 5. (Factory use only) CO2Abc self-calibration mode
1. The LCD displays:
2. This is for factory calibration use only. Please do not change it.
3. Click the“right-side button” again to enter set 6.
5. OPERATION
SET 6. CO2manual calibration
1. The LCD displays:
2. Directly increase or decrease the displayed value of CO2, press
the to move the digit, and the selected digit will ash.
3. Press or to modify the value.
4. Press the“right-side button”again to enter set 7.

P.13
5. OPERATION
SET 7. Temperature calibration
1. The LCD displays:
2. Directly increase or decrease the displayed value of CO2, press
the to move the digit, and the selected digit will ash.
3. Press or to modify the value.
4. Press the“right-side button”again to enter set 8.
SET 8. Humidity calibration
1. The LCD displays:
2. Directly increase or decrease the displayed value of CO2, press
the to move the digit, and the selected digit will ash.
3. Press or to modify the value.
4. Press the right-side button again to return to the measurement
mode.

P.14
6. GENERAL SPECIFICATIONS
• Real-time measurement of CO2/PM2.5/PM10/temperature/humidity.
• Maximum / minimum / average value.
• Auto-power on / o function.
• Adjustment and calibration function (CO2/temperature/humidity).
• CO2/PM2.5/PM10 red backlight alarm.
• Manual record and auto-record.
• Key sound assists to ensure the operation works.
• Overload indication .
• Battery: 3.7V 2000mAh rechargeable lithium battery
• Transformer for charging: 1A/5V
• Battery life: continuous use for approximately 6 hours
• 5V micro USB interface for external power supply
• When battery-low indicator
shows as the following gure,
the power will be turned
o after 5 seconds.
• Charging indication: The battery indicator will sequentially vary as
from right to left during charging and keep when fully charged.
• °C or °F unit selection.
• When the external power supply is connected, the auto-power o is
disabled, and the white backlight is always on.

P.15
6. GENERAL SPECIFICATIONS
• CO2 /PM2.5/PM10 red backlight alarm setting function
When the measured value reaches the setting value for alarm, the LCD
backlight shines in red and related measurement items ash.
• 20 logs for manual and automatic recording values.
• Auto-recording time interval setting: 5 seconds, 10 seconds, 5 minutes, 10
minutes, 20 minutes, 30 minutes, 60 minutes.
• Sampling time: 2.5 seconds (5 types, 0.5 seconds for each).
• Dimensions: 150x65x22mm (L x W x H).
• Weight: 190 g.
• Operating temperature and humidity: 0°C ~ +50°C, <80%RH
(no condensation).
• Storage temperature and humidity: 0°C ~ +60°C, <70%RH
(no condensation).
• Display size: 52mm (L) x 40mm (W).
Setting
value
CO2
1000PPM
PM2.5
35µg/m³
PM10
75µg/m³
CAUTION
If to use the meter in a high-humidity environment,
please place the meter in a low-humidity environment
for 24 hours after use.

P.16
6. GENERAL SPECIFICATIONS
SENSOR LASER PARTICULATE MATTER SENSOR
Measuring range 0-500 μg/m3
Resolution 1
Reaction time <10seconds
Accuracy ±8μg :<=50µg/m3
±10% of reading value:>50µg/m3
Ambient temperature range for accurate measure:
18°C (64°F) ~ 28°C (82°F)
6.1 PM2.5
SENSOR LASER PARTICULATE MATTER SENSOR
Measuring range 0-500 μg/m3
Resolution 1
Reaction time <10seconds
Accuracy ±10μg :<=50µg/m3
±15% of reading value:>50µg/m3
6.2 PM10

P.17
6. GENERAL SPECIFICATIONS
SENSOR NONDISPERSION INFRAREDNDIR
Measuring range 400 to 9999ppm
Resolution ±1ppm
Reaction time 90% during about 2 minutes
Accuracy ±70ppm ±3% of readings.
(400-2000ppm)
6.3 CO2
SENSOR BANDGAP TEMPERATURE SENSOR
Measuring range -10°C~50°C / 14°F~122°F
Resolution 0.1°C / 0.1F (0~35°C / 32°F~95°F) ;
1°C / 1°F
(Above 100°C /°F or below -10°C /°F)
Reaction time About 1 second
Accuracy ±1.0°C/±1.8°F
(Non-charging and 30 minutes after charging)
6.4 TEMPERATURE

P.18
6. GENERAL SPECIFICATIONS
SENSOR CAPACITIVE HUMIDITY SENSOR
Measuring range 1-99%
Resolution 0.1%
Reaction time About 4 seconds
Accuracy ±5.0%RH(10~90%);
±8.0%RH(<10%,>90%) no
condensation, at 25°C
6.5 HUMIDITY

7. MAINTENANCE OR REPAIR
8. PRODUCT DISPOSAL
P.19
1. For the battery-low indicator: indicates the battery full;
indicates the battery low, please charge it in time.
2. If dirty, please wipe it with a soft cloth, such as a glasses cloth.
Do not wipe it with chemical solvents.
3. If fault on the meter, it can only be sent to the authorized
service suppliers or sent back to the original factory for
maintenance.
CAUTION
When the LCD shows the battery-low indicator ,
please charge it in time.
7. MAINTENANCE OR REPAIR
8. PRODUCT DISPOSAL
Caution: This symbol indicates that this
product and its accessories shall be subject
to a separate collection and correct
disposal, please not throw it away directly to
avoid environmental pollution.