Permobil ConnectMe F3 User manual

Installation instruction

ConnectMe
Contents
Installation .......................................................................................3
Installation F3/F5/M3/M5 ................................................................4
Installation M300/M400 ..................................................................15
Software update .............................................................................23
Nominal ConnectMe LED behavior ................................................24
Tools needed for software update ..................................................25
Edition: 1, 2017-01
Order no: 332766

ConnectMe
3
Installation
e ConnectMe must be installed by an authorized service technician. If ConnectMe is wrong-
fully installed it can cause damage to the ConnectMe, the wheelchair and/or other property.

ConnectMe
4
Installation – F3/F5/M3/M5
1 .
Switch the main fuse to OFF position.
2 .
Remove the two knobs holding the top
chassis covers.

ConnectMe
5
Installation – F3/F5/M3/M5
3 .
Remove the top cover.
4 .
Pull the rear chassis cover backwars to
remove it.

ConnectMe
6
Installation – F3/F5/M3/M5
5 .
Pull the front chassis cover forward to
remove it.
6 .
Locate the ICS Master Module in the front
of the chassis.

ConnectMe
7
Installation – F3/F5/M3/M5
7 .
Remove the plastic plug covering
J6 connector. Recycle the plug.
8 .
Locate the J6 serial channel (PC) and the
R-net connector 3 on the ICS box.

ConnectMe
8
Installation – F3/F5/M3/M5
9 .
Connect the ConnectMe R-net cable to
the connector marked with ”3” in the
illustration.
10.
Connect the ConnectMe ICS cable to the
J6 connector.

ConnectMe
9
Installation – F3/F5/M3/M5
11.
Push the cable box down between the ICS
module and the chassis according to the
illustration.
12.
Route the cable backwards on the right side
of the chair. Push the cable down in the two
cable guides.

ConnectMe
10
Installation – F3/F5/M3/M5
13.
Remove the plastic film covering the Dula
lock. Mount it on the ConnectMe box.
14.
Remove the plastic film covering
the other side of the Dula lock.
Push the EPDM rubber againts the
adhesive to fix it.

ConnectMe
11
Installation – F3/F5/M3/M5
15.
Remove the plastic film covering the EPDM
rubber.
16.
Clean the area shown in the illustration.

ConnectMe
12
Installation – F3/F5/M3/M5
17.
Fix ConnectMe on the battery wall
according to the illustration.
18.
Mount rear cover.

ConnectMe
13
Installation – F3/F5/M3/M5
19.
Mount top cover.
20.
Mount front cover.

ConnectMe
14
Installation – F3/F5/M3/M5
21.
Fix the covers with the knobs.
22.
Turn the main fuse to ON position.

ConnectMe
15
Installation – M300/M400
1 .
Switch off the main fuse. It is located below
the rear lights on the chassis.
2 .
Remove the two knobs holding the
chassis front cover.

ConnectMe
16
Installation – M300/M400
3.
Remove the rear chassis cover by lifting it
upwards and backwards. On wheelchairs
equipped with lights, disconnect the rear
lights cabling.
4 .
The ICS Master Module is located
behind the rear chassis cover.

ConnectMe
17
Installation – M300/M400
5 .
Remove the cover of the ICS Master
Module by sliding it off.
6 .
On the cover of the ICS Master Module
there is connection overview. Plug in the
ConnectMe ICS connector in connection J3.

ConnectMe
18
Installation – M300/M400
7 .
Hold the cable according to the picture
and slide the cover of the ICS Master
Module back in place.
8 .
Connect the R-net cable in the R-net bay
underneath the fuse.

ConnectMe
19
Installation – M300/M400
9 .
Clean the area under the fuse and mount
the Dula lock on it.
10.
Fix ConnectMe to the main fuse with the
cables to the right.

ConnectMe
20
Installation – M300/M400
11.
Route the cable according to the illustration.
12.
Route the cable according to the illustration.