Pet Gear ON-THE-GO Pet PG8250 User manual

To see our full line of products, visit us online at: www.petgearinc.com
CUSTOMER SERVICE HELP DESK
[email protected]
Toll-Free 877-752-9123 - Eastern Standard Time 8am-3pm, Monday through Friday
For The ON-THE-GO Pet™
INSTRUCTION MANUAL
SPECIAL EDITION PET STROLLER
PG8250
Interior Dimensions:
26"L x 12"W x 19.5"H

SPECIAL EDITION PET STROLLER • PG8250
2
PARTS LIST
OPENING THE STROLLER
Step 1. Release locking latch
Check that you have all the parts shown BEFORE assembling your product.
If any parts are missing, call Customer Service.
Step 2. Unfold as shown.
Make sure both locks snap into place.
Stroller
Back Tray
Front Wheel
Assembly 2-Rear Wheels
2-Washers 2-Cotter Pins 2-Hub Caps
Rear Axle Assembly
Latch

SPECIAL EDITION PET STROLLER • PG8250 3
TO ASSEMBLE FRONT WHEELS
TO ASSEMBLE REAR WHEELS
Step 1. Slide wheel assembly onto axle.
Step 2. Slide washer onto axle.
Step 3. Fit straight part of cotter pin
through hole on axle.
Note Direction
of Arrow
NOTE: To remove, squeeze
tab and pull wheel off.
Step 1. Turn stroller over as shown.
Step 2. Push wheel assembly onto stroller leg
until it snaps into place.
Step 3. Repeat for other wheel.
Tug rmly on each wheel assembly to be sure
wheels are securely in place.

SPECIAL EDITION PET STROLLER • PG8250
4
Step 4. Line up each of the tabs in the hub cap with
the slots in the wheel, snap hub cap into place.
Step 5. Repeat for other side.
Step 1. Turn stroller over.
Step 2. Position rear axle assembly as shown.
Step 3. Push rear axle onto frame until it clicks and
locks into place on both sides.
NOTE: Pull down rmly on the brackets to be sure
they are securely attached to the stroller’s rear legs.
Step 1. To assemble the back tray, rst align a
hole on one side of the tray with one of the bolts
on the handle of the same side of the stroller.
Step 2. Snap one side of the tray over the bolt
on the handle then repeat for the other side.
TO ASSEMBLE REAR WHEELS
TO ASSEMBLE REAR AXLE TO FRAME
TO ASSEMBLE BACK TRAY

SPECIAL EDITION PET STROLLER • PG8250 5
Step 1. To engage the front wheel locking mechanism so that
the front wheel does not swivel, (best when the stroller is used
for fast walking or running), pull tab up.
Step 2. To disengage the locking mechanism so that the front
wheel swivels (for easy steering) push tab down.
TO USE FRONT WHEEL LOCKING MECHANISM
APPLYING THE BRAKES
Unlock
Lock
Step 1. Push levers on both rear wheels down to lock.
Step 2. Pull levers up to unlock.
WARNING: Never leave your stroller parked without applying brakes.
Unlock
Lock
FOLDING THE STROLLER
Step 1. NOTE: Before folding the
stroller, unzip stroller, and open
the canopy.
Step 2. Slide second frame lock
release (C) to the right, while
squeezing the main frame lock
release (D) rotate the folding
mechanism almost 180 degrees
forward until stroller releases
and handle is lowered.
C.
SLIDE TO RIGHT

SPECIAL EDITION PET STROLLER • PG8250
6
LOOKING AFTER YOUR STROLLER
WHEEL MAINTENANCE
• Always store product in a clean, dry place.
• Not recommended for use on the beach.
• Do not put heavy items on top of the stroller.
• Clean frame by wiping with a lightly oiled cloth.
• Do not use detergent or abrasives. Spot clean fabric with dry cleaning uid or mild soap
and warm water.
• To ensure easy maneuverability and to minimize wear and tear, (especially wheels, axles,
and swivels), keep all moving parts clean and lubricated with WD40®or light machine oil.
• NOTE: Do not lubricate brake components or swivel locks.
• Regularly check stroller for loose parts. These should be tightened or replaced.
• To clean and lubricate front and rear wheels, push out locking lever under wheel housing
to release rear wheel.
• To ensure ease of maneuverability and to minimize wear and tear, keep all moving parts
clean and lubricated with WD40®or light machine oil.
• Push wheel sets back on until they click and lock in position; pull on wheel housings to
ensure they are secure.
• Push stroller back and forth and rotate swivels around to work in lubricant.
• Clean the rear wheel assembly and the rest of the frame with warm, soapy water; clean
off with warm water and dry thoroughly.
• NOTE: Do not lubricate brake components or swivel locks.
C. D.
SLIDE TO RIGHT AND ROTATE 180 DEGREES FORWARD WHILE
SQUEEZING MAIN FRAME (D) LOCK RELEASE
FOLDING THE STROLLER

SPECIAL EDITION PET STROLLER • PG8250 7
WARNING!
FOR PETS ONLY.
Not intended to be used as a restraining device for aggressive or dangerous animals that dig, chew or paw
aggressively. Do not leave your pet unattended. PET GEAR is not liable for any damage caused by aggressive,
destructive, immature or untrained animals. Do not use near an open or exposed ame. Failure to follow these
warnings and the instructions could result in serious injury or death.
• Do not carry additional bags, goods, or accessories in or on stroller except as recommended in the
manufacturer’s instructions.
• Recommended use of an approved safety restraint correctly tted and adjusted.
• Do not leave pet unsupervised in stroller.
• Before making adjustments to stroller ensure that pet’s body is clear of any moving parts.
• This stroller is designed for one pet only.
• Do not hang bags from handles as this may cause the product to become unstable.
• Do not use on escalator or stairs; fold stroller and carry.
• Put on brake whenever you park the stroller.
• Ensure stroller is completely erected and check that all locks are engaged before placing pet in stroller.
• Do not overload as stroller may become unstable; maximum weight of pet using this stroller not to
exceed 45 lbs.
• Any goods carried in the basket not to exceed 6 lbs.
REPLACEMENT PARTS
Use only PET GEAR replacement parts.
Please have your model number ready before calling.
You can also request parts: http://www.petgearinc.com/main.asp?sel=2
192 Sheldon Avenue • West Rutland, VT 05777 • 877-752-9123 • www.petgearinc.com