PhaseOne RP1 1600 User manual

PHASEONE TABLE TOP COLUMN
INSTALLATION MANUAL
READ CAREFULLY BEFORE UNPACKING!

UNPACK THE TABLE
A
DETAIL A
2. 1.
Instal the remote holder:
The remote holder (1.) is located underneath the table.
Loosen knobs (2.) to slide out the remote holder.
Place the remote holder facin out and reti hten the knobs.
B
DETAIL B
4.
3.
POS.1
POS.2
POS.4
POS.3
LEVEL THE TABLE
Level the table by adjustin the feet.
Adjust the feet by usin wrench no.10
Turn the bottom nut (3.) Clockwise (CW) to move the table up.
Note the feet are fully screwed in when unpackin .
So always start levelin by turnin a foot out (CW)
Level the table usin a spirit level, followin the position scheme.
When the table is levelled thi hthen nuts 4 (CCW). usin wrench no. 17
towards the table to fix it into position.
NECESSARY BOLTS AND KEYS ARE SUPPLIED
INSIDE THE BROWN ACCESSORY BOX INSIDE THE COLUMN PACKAGING

UNPACK THE COLUMN
Unpack the column by liftin it vertically from the packa in .
Remove the plastic and start by fixin the column to the table.
FIX THE COLUMN TO THE TABLE
1.
2.
4.
3.
D
DETAIL D
Place the footplate of the column on top of the metal insert plat of the table carefully.
Fix the column to the table usin the four supplied M8x30 countersunk bolts usin Allen Key 5mm
Ti hten firmly!
IMPORTANT NOTE! DO NOT TOUCH THE SET SCREWS. THESE ARE PRE-SET!!

FIX THE QUICK RELEASE
Fix the quick release with the knob pointin up!
Push the pins of the quick release in the desi nated holes of the levelin plate.
Fix the quick release usin the supplied 3/8 bolt usin key 5/16
Ti hten firmly.
Fix with knob pointin up!
place 3/8 bolt from the rear
LEVEL THE QUICKRELEASE
A1. A2.
To level the quick release (QR) in the horizontal plane
Use Allen Key 2,5mm to set the screws A1 and A2.
To adjust the QR clockwise, fully loosen setscrew A1,
then ti hten A2 until the camera is levelled.
Then re-ti hten set screw A1.
DO NOT OVER-TIGHTEN, FIXED IS FIXED.
To adjust the QR counter clockwise,
fully loosen setscrew A2 then ti hten A1 until the camera is levelled.
Re-ti hten A1 to fix position.
B1
B2 B3
To level the vertical plane, set the level screws B usin Allen Key 5 mm.
Set srews B2 and B3 to tilt and swin the camera,
by ti htenin or loosenin B2 and B3.
Note: only in exceptional circumstances screw B1 is used!
B1 is only used when the adjustment of B2 and B3 is not sufficient.

FIX THE MOTOR CASE
Fix the motor control box to the back of the column by usin the desi nated velcro strips.
Fix the motor case to the footplate by usin the supplied m3x6 socket head cap screws usin the 2mm Allen Key.

CABLE GUIDANCE
E
DETAIL E
Open the links in the corner from the inside.
Feed both ends of the downwards throu h the calbe chain.
Use the supplied re-useable cable straps to fix the cable to the chain for strain relief.
To remove the chain from the column, open two or three links above the mountin link.
Dependin on the end of the cable, you can now squeeze or push open the links to remove them
from the mountin link.
F
DETAIL F
Fix the cables here, usin re-useable cable straps for strain relief