PHI PSE04 User manual

Multiple Sound Siren PSE04
The PSE04 is a wireless siren, based on Z-WaveTM technology. It is the
Z-WaveTM lus roduct, it su ort the security, OTA... Those newest
features of the Z-WaveTM technology. Z-WaveTM is a wireless
communication rotocol designed for home automation, s ecifically to
remotely control a lications in residential and light commercial
environments. The technology uses a low- ower RF radio embedded or
retrofitted into home electronics devices and systems, such as lighting,
home access control, entertainment systems and household a liances.
This roduct can be included and o erated in any Z-WaveTM network
with other Z-WaveTM certified devices from other manufacturers and/or
other a lications. All non-battery o erated nodes within the network
will act as re eaters regardless of vendor to increase reliability of the
network.
The device ado t the Z-WaveTM 700 series chi , when your Z-WaveTM
network system is all made by Z-WaveTM 700 series devices. The
network system will have the advantages as below.
•Concurrent multi-channel su ort reduces external interference.
•Better RF range, im rove about 10 meters in indoor.
•Su ort 100 Kb s transmit s eed, s eed u communication.
Specification
Rating 6VDC (AA Battery *4)
RF distance Min. 40M indoor,
100M outdoor line of sight,
RF Frequency
868.40 MHz, 869.85 MHz(EU)
908.40 MHz, 916.00 MHz(US)
920.9MHz, 921.7MHz, 923.1MHz
(TW/KR/Thai/SG)
921.40 MHz, 919.80 MHz(ANZ)
869.00 MHz(RU)
865.20 MHz(IN)
916.00 MHz(IL)
RF Maximum Power +10dBm (Peak), -10dBm
(Average)
Dimension 170mm(L) X 48mm (W) X 30(H)
Weight 205g
IP classification IP44; Outdoor use
O eration tem erature -20 to 55° C
Humidity 85%RH max
FCC ID RHHPSE04
Marking CE/NCC
1

S ecifications are subject to change and im rovement without
notice.
Troubleshooting
Sym tom Cause of Failure Recommendation
The device can not
join to Z-Wave™
network
The device may in a Z-
Wave™ network.
Exclude the device
then include again.
For Instruction to http:// www.philio-tech.com
Overview
2

Battery Installation
When the device re ort the low battery message. The user should
re lace the battery to new one. The battery ty e is AA, 1.5V
Please loosen the screw on the back cover to release the front cover
3

Adding to Z-WaveTM etwork
There is one tam er key on the device. The tam er key can add,
remove, reset from Z-WaveTM network.
In the first time, add the device into the Z-WaveTM network. First, make
sure the rimary controller is in the add mode. And then ower on the
device. The device will auto start the smartstart Inclusion mode.
otice: Including a node ID allocated by Z-WaveTM Controller means
“Add” or “Inclusion”. Excluding a node ID allocated by Z-WaveTM
Controller means “Remove” or “Exclusion”.
Function Description
Add
1. Have Z-WaveTM Controller entered inclusion mode.
2. Pressing tam er key three times within 1.5 seconds
to enter the inclusion mode.
3. After add successful, the LED will light ON 1 second
Remove
1. Have Z-WaveTM Controller entered exclusion mode.
2. Pressing tam er key three times within 1.5 seconds
to enter the exclusion mode.
Node ID has been excluded.
Reset
otice: Use this procedure only in the event
that the primary controller is lost or
otherwise inoperable.
1. Pressing tam er key four times within 1.5 seconds
and do not release the tam er key in the 4th
ressed, and the LED will light ON.
2. After 3 seconds the LED will turn OFF, after that
within 2 seconds, release the tam er key. If
successful, the LED will light ON one second.
Otherwise, the LED will flash once.
3. IDs are excluded and all settings will reset to
factory default.
SmartStart
1. Product has a DSK string , you can key in first five
digit to increment SmartStart rocess,or you can
scan QR code.
Ex:mydsk
10209-46687-52248-13629-04783-07465-15776-56519
2. SmartStart enabled roducts can be added into a
Z-Wave network by scanning the Z-Wave QR Code
resent on the roduct roviding SmartStart
inclusion. No further action is required and the
SmartStart roduct will be added automatically
within 10 minutes of minutes On in the network
vicinity.
*notice1:The QR code can be found on the device
PSE04 or on the box.
Association
This machine rovides one grou s of nodes. Each
grou can set 1 Nodes.
Grou 1: Used for returned events.
Re ort ty e:
1.Notification re ort
2.Sensor multilevel re ort
3.Device Reset Locally Notification
4.Battery Re ort
5.Indicator Re ort
•Failed or success in including/excluding the node ID can be
viewed from Z-WaveTM Controller.
otice 1: Always RESET a Z-WaveTM device before trying to add it to a
Z-WaveTM network.
4

Z-WaveTM Message Report
In default the device will using Notification Re ort to re resent the
tam er trigger event.
* Tamper Report:
When the tam er key is ressed over 5 seconds. The device will into
the alarm state. In that state, if the tam er key be released, the device
will unsolicited to send the re ort to the nodes in the grou 1.
Notification Re ort (V8)
Notification Ty e: Home Security (0x07)
Event: Tam ering. Product covering removed (0x03)
* Siren State Report:
When the siren start laying or sto the alarm sounds, the device will
unsolicited to send the “Notification Re ort” to the nodes in the grou
1.
Notification Re ort (V8)
Notification Ty e: Siren (0x0E)
Event: Siren active (0x01) , Siren idle (0x00)
*Temperature Report:
When the tem erature differential over, the device will unsolicited to
send the “Sensor Multilevel Re ort” to the nodes in the lifeline grou .
Sensor Ty e: Tem erature (0x01)
*** Tem erature differential re ort ***
This function default is disable, to enable this function by setting the
configuration NO.5 is greater than 0.
In the default, is disable tem erature differential re ort.
If setting the configuration NO.5 to 1, when the tem erature is
changed to lus or minus one degree Fahrenheit (0.56 degree Celsius),
the device will re ort tem erature information to the nodes in the
lifeline grou .
The device will measure the tem erature in every 10 seconds. And if
the tem erature is over 140 degree Fahrenheit (60 degree Celsius), the
device will always re ort in each measurement.
Notice 1: The PSE04 must stay awake for at least 2 seconds after
communicating, so therefore the more communication, the power
consumption fast, lease ay attention to use configuration NO.5.
Notice 2: This roduct cannot reflect outdoor tem erature immediately
because of the tem erature sensor equi ed inside rather than surface.
Power Up Procedure
Play Sound
Using the SWITCH_BINARY_SET or BASIC_SET to lay the siren, Basic
Set or Switch Binary Set with Value 0xFF, the Sound ID will be the same as
the value which was set in Configuration No.7, 0x00 will sto to lay.
Basic Set (V1)
Value Sound
0x00 Sto Play
0x01 Fire
0x02 Ambulance
0x03 Police
0x04 Alarm
0x05 Ding Dong
0x06 Bee
0xFF Same as configuration NO.7 setting.
5

Switch Binary Set (V1)
Value Sound
0x00 Sto Play
0xFF Same as configuration NO.7 setting.
Over The Air (OTA) Firmware Update
The device is supported with Z-Wave™ firmware update via OTA.
1. et the Z-WaveTM Controller into the firmware update mode.
2. Choose the hex file to update the firmware.
3. Wait 10~15 minutes for completing the OTA process.
4. Result of OTA will show in Z-Wave™ Controller log.
During the OTA process, please DO NOT remove the power,
otherwise, the firmware will be broken, and the device will be
nonfunctional.
Z-Wave Configuration Settings
Notice 1: All of the configuration, the data size is 1.
Notice 2: The reserve bit or not su orted bit is allowed any value, but no
effect.
Notice 3: The PSE04 must stay awake for at least 2 seconds after
communicating, so therefore the more communication, the power
consumption fast, lease ay attention to use configuration NO.1, NO.4,
NO.5, NO.6.
NO. Name Def. Valid Descri tion
1Auto Re ort
Tick Interval 0x1E 0~255 The interval time for auto re ort each tick.
2 Sound 0x06 0~127 Play sound duration, 1 tick is 30
Duration seconds.
3Customer
Function
0x00 All Customer function switch, using
bit control.
0Bit0: Disable Trigger Alarm.
0:Enable , 1:Disable.
0Bit1: Disable Sound. Only using o tical alarm. 0:Enable ,
1:Disable.
0Bit2: Tem erature Unit.
0:Fahrenheit , 1:Celsius.
0Bit3: Reserve.
0Bit4: Reserve.
0Bit5: Reserve.
0Bit6: Reserve.
0Bit7: Reserve.
4
Auto Re ort
Tem erature
Time 0x0C 0~127 The interval time for auto re ort the tem erature.
5
Tem erature
Differential
Re ort
0x00 0~127 The tem erature differential to
re ort.
6Auto Re ort
Battery Time 0x0C 0~127 The interval time for auto re ort the battery level.
7 Play Sound
Control 0x41 All Control lay sound's level and which sound.
1Bit0~1: Play sound's level. Level
1~3.
0Bit2: Reserve.
6

0Bit3: Reserve.
4
Bit4~7: Which sound id will
lay, when control form
controller.
Sound ID 1~6, 0: Disable.
Z-Wave Supported Command Class
Command Class Version Required Security Class
Z-Wave Plus™ Info 2None
Security 1None
Security 2 1None
Su ervision 1None
Trans ort Service 2None
Association 2Highest granted Security Class
Association Grou
Information
3Highest granted Security Class
Device Reset Locally 1Highest granted Security Class
Firmware U date Meta
Data
5Highest granted Security Class
Indicator 3Highest granted Security Class
Manufacturer S ecific 2Highest granted Security Class
Multi-Channel Association 3Highest granted Security Class
Powerlevel 1Highest granted Security Class
Version 3Highest granted Security Class
Configuration 4Highest granted Security Class
Sensor Multilevel 11 Highest granted Security Class
Basic 1 Highest granted Security Class
Switch Binary 1 Highest granted Security Class
Notification 8 Highest granted Security Class
Battery 1 Highest granted Security Class
CAUTIO
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used battery according to the instructions.
Choosing a Suitable Location
1. The suitable ambient tem erature for the module/device is
0°C~40°C.
2. Do NOT lace the module/device direct under sunlight, in a humid
lace or in any location where they may contact moisture, dirt, dust.
3. Do NOT lace the module/device where exists combustible
substances or any source of heat, fires, radiators, boiler etc.
Disposal
This marking indicates that this roduct should not
be dis osed with other household wastes throughout
the EU. To revent ossible harm to the environment
or human health from uncontrolled waste dis osal,
recycle it res onsibly to romote the sustainable
reuse of material resources. To return your used
device, lease use the return and collection systems
or contact the retailer where the roduct was
urchased. They can take this roduct for
environmentally safe recycling.
7

Philio Technology Cor oration
8F., No.653-2, Zhongzheng Rd., Xinzhuang Dist., New Tai ei City 24257,
Taiwan(R.O.C)
w ww. hilio-tech.com
FCC Interference Statement
This equi ment has been tested and found to com ly with the limits
for a Class B digital device, ursuant to Part 15 of the FCC Rules.
These limits are designed to rovide reasonable rotection against
harmful interference in a residential installation.
This equi ment generates, uses, and can radiate radio frequency en-
ergy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
articular installation.
If this equi ment does cause harmful interference to radio or televi-
sion rece tion, which can be determined by turning the equi ment off
and on, the user is encouraged to try to correct the interference by one
of the following measures:
•Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is sub-
ject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including inter-
ference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to
operate this equipment.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
8