Philco PX 502 Iceberg User manual

REFRIGERATOR FREEZER
USER’S MANUAL
PX 502 Iceberg

Copyright © 2016, Fast ČR, a. s. 04/2016
Dear customer,
Thank you for buying aPHILCO brand product. So that your appliance serves you well, please read
all the instructions in this user’smanual.

EN - 1
Copyright © 2016, Fast ČR, a. s. 04/2016
CONTENTS
PART 1: Safety information............................................................................................................................. 2
• General safety ..................................................................................................................................................................................2
• Daily use.............................................................................................................................................................................................3
• Care and cleaning...........................................................................................................................................................................3
• Installation.........................................................................................................................................................................................4
• Service ................................................................................................................................................................................................4
• Energy saving...................................................................................................................................................................................4
• Environment Protection...............................................................................................................................................................4
PART 2: Overview............................................................................................................................................. 6
PART 3: Preparing before using...................................................................................................................... 7
• Specication of product...............................................................................................................................................................7
PART 4: Correct Use for Your Refrigerator ..................................................................................................... 8
• New refrigerator is coming..........................................................................................................................................................8
• Instruction to height adjustment of the door......................................................................................................................8
PART 5: Refrigerators transportion and location........................................................................................ 10
• Transportion.................................................................................................................................................................................. 10
• Location........................................................................................................................................................................................... 10
PART 6: Start using ........................................................................................................................................ 11
• Refrigerator compartment....................................................................................................................................................... 11
• Shelf adjustment.......................................................................................................................................................................... 11
Part 7: Refrigerator compartment................................................................................................................ 13
Part 8: Freezer compartment........................................................................................................................ 14
• Freezer compartment is for food storage for a long time............................................................................................. 14
Part 9: Introduction of Function................................................................................................................... 18
• Display Control ............................................................................................................................................................................. 18
• Key Operation ............................................................................................................................................................................... 18
Part 10: Maintenance and care refrigerator ................................................................................................ 21
• When Shutting o the refrigerator........................................................................................................................................ 22
• Energy Saving Tips ...................................................................................................................................................................... 23
PART 11: INFORMATION SHEET .................................................................................................................... 24

EN - 2
Copyright © 2016, Fast ČR, a. s. 04/2016
PART 1: SAFETY INFORMATION
In the interest of your safety and to ensure the correct use, before installing and rst using the appliance, read
this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is
important to ensure that all people using the appliance are thoroughly familiar with its operation and safety
features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so
that everyone using it through its life will be properly informed on appliance use and safety.
For the safety of life and property keep the precautions of these user’sinstructions as the manufacturer is not
responsible for damages caused by omission.
General safety
• This appliance can be used by children aged from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge if they have been given super vision or
instruction concerning use of the appliance in asafe way and understand the hazards involved.
• Children should be supervised to ensure that they do not play with the appliance.
• Cleaning and user maintenance shall not be made by children unless they are aged from 8 years and above
and supervised.
• Keep all packaging well away from children. There is risk of suocation.
• If you are discarding the appliance pull the plug out of the socket, cut the connection cable (as close to the
appliance as you can) and remove the door to prevent playing children to suer electric shock or to close
themselves into it.
• If this appliance featuring magnetic door seals is to replace an older appliance having aspring lock (latch)
on the door or lid, be sure to make that spring lack unusable before you discard the old appliance. This will
prevent it from becoming adeath trap for achild.
WARNING! Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear
of obstruction.
WARNING! Do not use mechanical devices or other means to accelerate the defrosting process,
other than those recommended by the manufacturer.
WARNING! Do not damage the refrigerant circuit.
WARNING! Do not use other electrical appliances (such as ice cream makers) inside of refrigerating
appliances, unless they are approved for this purpose by the manufacture.
WARNING! Do not touch the light bulb if it has been on for along period of time because it could
be very hot.1)
• Do not store explosive substances such as aerosol cans with aammable propellant in this appliance.
• The refrigerant isobutane (R600a) is contained within the refrigerant circuit of the appliance, anatural gas
with ahigh level of environmental compatibility, which is nevertheless ammable.
• During transportation and installation of the appliance, be certain that none of the components of the
refrigerant circuit become damaged.

EN - 3
Copyright © 2016, Fast ČR, a. s. 04/2016
- avoid open ames and sources of ignition
- thoroughly ventilate the room in which the appliance is situated
• It is dangerous to alter the specifications or modify this product in any way. Any damage to the cord may
cause ashort circuit, fire and/or electric shock.
•This appliance is intended to be used in household.
WARNING! Any electrical components(plug, power cord, compressor and etc.) must be replaced by
acertied service agent or qualied service personnel.
WARNING! The light bulb supplied with this appliance is a“special use lamp bulb”usable only with
the appliance supplied. This“special use lamp” is not usable for domestic lighting.1)
• Power cord must not be lengthened.
• Make sure that the power plug is not squashed or damaged by the back of the appliance. Asquashed or
damaged power plug may overheat and cause are.
• Make sure that you can come to the mains plug of the appliance.
• Do not pull the mains cable.
• If the power plug socket is loose, do not insert the power plug. There is arisk of electric shock or re.
• You must not operate the appliance without the lamp.
• This appliance is heavy. Care should be taken when moving it.
• Do not remove nor touch items from the freezer compartment if you hands are damp/wet, as this could
cause skin abrasions or frost/freezer burns.
• Avoid prolonged exposure of the appliance to direct sunlight.
Daily use
• Do not put hot on the plastic parts in the appliance.
• Do not place food products directly against the rear wall.
• Frozen food must not be re-frozen once it has been thawed out. 1)
• Store pre-packed frozen food in accordance with the frozen food manufactures instructions. 1)
• Appliance s manufactures storage recommendations should be strictly adhered to. Refer to relevant
instructions.
• Do not place carbonated of zzy drinks in the freezer compartment as it creates pressure on the container,
which may cause it to explode, resulting in damage to the appliance. 1)
• Ice lollies can cause frost burns if consumed straight from the appliance. 1)
Care and cleaning
• Before maintenance, switch o the appliance and disconnect the mains plug from the mains socket.
• Do not clean the appliance with metal objects.
• Do not use sharp objects to remove frost from the appliance. Use aplastic scraper. 1)
• Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean the drain. If the drain
is blocked, water will collect in the bottom of the appliance. 2)

EN - 4
Copyright © 2016, Fast ČR, a. s. 04/2016
Installation
IMPORTANT!
For electrical connection carefully follow the instructions given in specic paragraphs.
• Unpack the appliance and check if there are damages on it. Do not connect the appliance if it is damaged.
Report possible damages immediately to the place you bought it. In that case retain packing.
• It is advisable to wait at least four hours before connecting the appliance to allow the oil to ow back in the
compressor.
• Adequate air circulation should be around the appliance, lacking this leads to overheating. To achieve
sucient ventilation follow the instructions relevant to installation.
• Wherever possible the spacers of the product should be against awall to avoid touching or catching warm
parts (compressor, condenser) to prevent possible burn.
• The appliance must not be located close to radiators or cookers.
• Make sure that the mains plug is accessible after the installation of the appliance.
Service
• Any electrical work required to do the servicing of the appliance should be carried out by aqualied
electrician or competent person.
• This product must be serviced by an authorized Service Center, and only genuine spare parts must be
used.
Energy saving
• Don’t put hot food in the appliance;
• Don’t pack food close together as this prevents air circulating;
• Make sure food don’t touch the back of the compartment(s);
• If electricity goes o, don’t open the door(s);
• Don’t open the door(s) frequently;
• Don’t keep the door(s) open for too long time;
• Don’t set the thermostat on exceeding cold temperatures;
• Some accessaries, such as drawers, can be removed to get larger storage volume and lower energy
consumption.
Environment Protection
This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant
circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and
rubbish. The insulation foam contains ammable gases: the appliance shall be disposed according
to the appliance regulations to obtain from your local authorities. Avoid damaging the cooling unit,
especially the heat exchanger. The materials used on this appliance marked by the symbol are
recyclable.

EN - 5
Copyright © 2016, Fast ČR, a. s. 04/2016
The symbol on the product or on its packaging indicates that this product may not be treated as
household waste. Instead it should be taken to the appropriate collection point for the recycling of
electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human health, which could other-
wise be caused by inappropriate waste handling of this product. For more detailed information about
recycling of this product, please contact your local council, your household waste disposal service or
the shop where you purchased the product.
Packaging materials
The materials with the symbol are recyclable. Dispose the packaging in asuitable collection containers to
recycle it.
Disposal of the appliance
1. Disconnect the mains plug from the mains socket.
2. Cut o the mains cable and discard it.
1) If there is afreezer compartment.
2) If there is afresh-food storage compartment.

EN - 6
Copyright © 2016, Fast ČR, a. s. 04/2016
PART 2: OVERVIEW
1.
2.
5.
3. 4.
6.
7.
8.
9.
1 Freezer door rack
2 Freezer compartment glass shelf
3 Ice-maker box
4 Ice box
5 Freezer compartment drawer
6 Refrigerator compartment glass shelf
7 Vegetable crisper
8 Refrigerator door rack
9 Lower cover
This illustration is only for hinting, the detail please check your appliance.

EN - 7
Copyright © 2016, Fast ČR, a. s. 04/2016
PART 3: PREPARING BEFORE USING
Specication of product
• Invariable keeping fresh technology
Separate windy system in refrigerator compartment, separate temperature control, stable storage
temperature, long time fresh.
• Defrost pre-cold
Technology of defrost pre-cold with purpose of keeping temperature stable in refrigerator, suitable for
keep food fresh.
• Aptitude defrosting
Defrosting depends on using frequency with purpose of energy saving.
• VIP anti-heat technology
Thick foaming in anti-heat layer, low energy consumption.
• Gliding shelves, convenient using
Freezer and refrigerator’s rack designed as gliding and stretching, it’s convenient to stored.
• Human aptitude
Freezing eect is adjusted according to storage temperature and inside temperature by computer.
• Nice dimension
Ultra-thin size; Ultra great volume; Refrigerator compartment uses the upscale armored glass rack.
• CFC and no-frost design. Fasting freezing
• Automatic alarm of problem
• Reliable compressor with good quality
• Opening door alarm, LED screen
• Vitamins fresh technology

EN - 8
Copyright © 2016, Fast ČR, a. s. 04/2016
PART 4: CORRECT USE FOR YOUR REFRIGERATOR
Warnings!
• Don’t use mechanical equipment or other methods to accelerate the defrosting process
except the means recommended by the manufacturer.
• Don’t use any electrical appliances in the food storage compartments except the model
recommended by the manufacture.
• The R600a refrigerant and cyclopentane foaming material used in the refrigerator are
inammable. All waste and discarded refrigerators shall be placed away from naked re
and they are not allowed to burn.
New refrigerator is coming
• Remove all packaging material before using the new refrigerator. This includes the foam base and all
adhesive tape holding the refrigerator accessories inside and outside.
• Clean both the inside and outside of the refrigerator with wet cloth (a little detergent could be added into
the warm water to wash the cloth and then wipe it again with the clean water);
• Prepare an independent two-pole socket with grounding contact for the refrigerator and it shall not share
a multi-purpose socket with other electrical appliances;
• Do connect grounding wire! The grounding pole of the socket shall be provided with a reliable grounding
wire.
• Open the refrigerator body and take out the accessory two screws from the instruction packaging bag;
then install them into the bottom beam as shown by the schematic diagram on the right.
Instruction to height adjustment of the door
Before adjusting the height of the door, rotate the downward adjusting nut counterclockwise (as shown in
Figure I) for 2 circles with a wrench, and loosen the downward adjusting nut. Rotate the upward adjusting
nut (as shown in Figure I) to adjust the height, and then tighten the downward adjusting nut clockwise again.
1. When the door of refrigerating chamber is low:
Open the door, use the accompanying wrench to rotate the upward adjusting nut counterclockwise
according to the method as shown in Figure I, to move it upward until it is parallel and level.
2. When the door of refrigerating chamber is high:
Open the door, use the accompanying wrench to rotate the upward adjusting nut clockwise according to
the method as shown in Figure I, to move it downward, until it is parallel and level.

EN - 9
Copyright © 2016, Fast ČR, a. s. 04/2016
5.
1.
2.
3.
4.
6.
Not level
Figure I
1. Fixed shaft
2. Leveling feet
3. Downward adjusting nut
4. Upward adjusting nut
5. Right
5. Wrench
NOTE:
Height adjustment cannot be too large. The total height can be adjusted to 5 mm!

EN - 10
Copyright © 2016, Fast ČR, a. s. 04/2016
PART 5: REFRIGERATORS TRANSPORTION AND
LOCATION
Transportion
Please don’t inverted, squeezed, virbration refrigertor. when moving, the tilt angle can’t larger than 45 degree.
When moving, dont cling the door or coping.
Location
Ensure proper air circulation around refrigerator, dont place the unit near heat source, direct sunlight, moisture
or water, avoid rust and weakening the insulation.
Top space at least 30cm, space on both the sides and back at least 10cm from the wall, So refrigeratordoor can
open or close convenience and emanate heat.
Installing the refrigerator on solid. level oor(If don’t level, it can adjust the leveler to level.)
Attention!
Dont allow the power cable pressed by refrigerator or other heavy object, lest damaging the power
cable, it may arouse suddenness.
Before connecting the power, please checking the voltage range of refrigerator and power supply
carefully.

EN - 11
Copyright © 2016, Fast ČR, a. s. 04/2016
PART 6: START USING
Before it is used, make sure that the refrigerator is installed on the solid and level oor. . To understand all the
attention to security matters.
1. After unsealing the refrigerator, to x lower cover on the refrigerator.
(If the door rugged, Please refer to the adjustment instructions which locate in the lower left corner of the
right panel of Refrigerator to adjust.)
2. Connect to power supply
After connecting to power supply, the refrigerator is in the default status, and it shows the actual chilled
and frozen temperature. The refrigerator has a Power-down memory, The rst time when it is power on,
then every time will be set up at the last power-down operation.
3. Work model of the refrigerator
Human mode: You can use Temperature Control keys to set the temperature.
4. Put the food into the refrigerator
After a period of time of the operation of electricity, the refrigerator inside is already full cooling. Then you
can put the food into the refrigerator and start using the refrigerator.
TIPS:
When the temperature is set to change or put new food into the refrigerator, It takes some time to balan-
ce the inside temperature. The length of this period depends on the size of the temperature change, the
temperature of surrounding environment, the frequency of opening door and the number of food, and
so on.
Refrigerator compartment
Put the food which are short-term storage or to eat at any time in the refrigerator comparment.
Although regulating temperature b will enable average temperature of the majority of regional cold rooms
maintain between 0-10 °C, it can not make long-term preservation of food. Therefore, refrigerator compart-
ment only use as a short-term food storage.
Shelf adjustment
According to the needs of food storage, you can adjust the
shelf to proper position; To facilitate the use of it or adjust-
ment the location, the shelf can be set to slip so that you can
use and adjust it easily. when you want to clear the shelf,
please move the shelf by the direction(1.), then turn the shelf
in the direction(2.) for 90° until it is Perpendicular to the orig-
inal direction, pull out the shelf by the direction (3.). 1.
2.
3.

EN - 12
Copyright © 2016, Fast ČR, a. s. 04/2016
Height adjustment and cleaning of rack
Lift the rack by the direction (1.), hold both the sides, then
pull it out by the direction (2.). After cleaning, to install the
rack by the opposite direction. You can also adjust the posi-
tion according to the height of stored food.
1.
2.

EN - 13
Copyright © 2016, Fast ČR, a. s. 04/2016
PART 7: REFRIGERATOR COMPARTMENT
Recommendations of storage area for all kinds of food
As the cycle of air-conditioning in the refrigerator, it makes the temperature of all area dierences. So dierent
kinds of food should be placed on dierent temperature region.
1.
2.
3.
3.
4.
5.
6.
7.
7.
7.
1. Store pasta, canned, milk, etc.
2. Store fast food, easy-string together gustatorius food, dairy products, etc.
3. Store cooked meat and sausage, etc.
4. Store fruits and vegetables, etc
5. Store eggs, butter, cheese, etc.
6. Store easy-open tin can, canned, spices, etc.
7. Store all kinds of bottled drinks and food

EN - 14
Copyright © 2016, Fast ČR, a. s. 04/2016
PART 8: FREEZER COMPARTMENT
Freezer compartment is for food storage for a long time
The temperature of freezer compartment is very low, so it can keep food fresh state for a long time.You’d better
put the food whichneed long period of time to save in this space. But, you should comply with the storage time
marked on food packaging.
Recommendations of storage area for all kinds of food
2.
1.
1.
3.
4.
5.
6.
6.
1 The storage grilles on the door of the freezer room (2 stars) are used for short-term storage of food and ice
cream.
2 The storage grilles in the freezer room are used for the storage of frozen food.
3 The glass shelves are used for the storage of frozen foods, such as sh, meat and ice cream.
4 Rotary ice maker is used to produce ice.
5 Ice box is used for the storage of ice lumps.
6 Freezer drawer is used for the storage of sh, meat and poultry with the food packaging.

EN - 15
Copyright © 2016, Fast ČR, a. s. 04/2016
Operation and precautions for ice maker
NOTE:
Connection of water pipes: please contact the after-sales Service Department of the Company or profe-
ssionals to install to avoid any risk.
Warning!
The water pipes must be connected under the condition of power-o. Electric shock may cause
serious injury or death.
User shall determine whether to require an anti-reux valve upon the installation of water pipe.
If required, user shall purchase it individually and install a single-way valve or an anti-reux valve on
the joint of water route, or make it installed by a specialized person.
Notices!
The water pipe cannot be used where environmental temperature is under 0, Or it may lead to freez-
ing.
The water pipe cannot be connected to hot water, which may lead to deformation.
The water pipe should be used in the pressure range 30-100psi.
Lower pressure may cause smaller ice pieces and longer water exiting time.
But higher pressure may damage the lter.
The pipe cannot be connected to drinks, alcohol or other liquids except for water.
1. Turn o the water-tap.
2. Connect water pipe onto the water-tap. The water pipe should be long enough to prevent the drop-o of
the water pipe caused by removing of refrigeratory.
3. Turn o the refrigeratory.
4. Use a connecting pipe to connect the water pipes behind the refrigeratory and on the water-tap.
5. To prevent the drop-o or leaking of the water pipes, they must be xed by xed pins.
6. Turn on the water tap to check leakage.
7. The refrigeratory is energized an used normally.
Use of Automatic Ice Maker/Ice& Water Dispenser
Notices!
The water pipes are used in the pressure range of 30-100psi.
Water softeners may damage the ice maker and must not be used.
Please check the ice pieces in the storage box when power- o above 1h.
If the ice pieces are thawing and binding together, please empty them,
because the bound ice pieces may cause Failure of the ice system.
Ice maker
When the ice pieces in the storage box are binding together, you had better to melt it with warm water rather
than smash and take out them with a sharp tool, which may damage the refrigeratory.

EN - 16
Copyright © 2016, Fast ČR, a. s. 04/2016
Supply of cold water
1. Choose the ice/water button on the display board, and make sure the water indicator turns on.
2. When the water switch plate is pressed by the cup, the cold water comes out.
3. When using the refrigeratory the rst time, water does not come out before the water tank in the
refrigerator is lled up. The normal manner to get water is pushing and holding the switch plate for 2-3
minutes.
4. After the water comes out, please discharge water for about 3 minutes to purge the air and smell of plastic
in the water pipe.
5. When cold water is required, it’s better to get some ice before getting water.
6. When getting water, it is normal for noise of valve operation.
1. Automatic ice maker operates when the freezer reaches the needed temperature below 0°C after a period
prescriptive time when the refrigeratory is energized. Under normal temperature, the time between the
refrigeratory’s rst energizing and rst making of ice is about 6 hours.
2. The ice rstly made after the installation of the refrigeratory shall be thrown away because of plastic smell
and impurities.
3. The time interval of ice making is about 2 hours, and the amount of the ice is dierent according to
dierent service conditions.
4. When the ice storage is full, the ice maker will stop automatically, and when the ice storage is empty, the
ice maker will make ice again automatically.
5. The noises for de-icing, motor operation, dropping of ice into the ice storage, and operation of water
supply valve may not happen periodically. They are not errors.
6. Please use the button on/o on the distributor to turn o the ice-making function when it is not required.
The ice maker is sold under ON state. If unnecessary, please turn o this function timely after installation of
the refrigeratory. When the ice-making function is turned on without connection of waterways, there are
operational noises of water supply valve.
7. When ice piece is smaller than usual in a certain period of time, please verify the replacement frequency
of the lter. When the lter reaches its operation time, the water supply pressure is lower and the made ice
piece is smaller.
8. When cleaning the ice storage box, turn o the ice-making function on the distributor before detaching
the ice storage box.
9. Do not whirl the Auger during reinstallation of the removed ice storage box. After being whirled, the
Auger cannot be assembled and installed normally. It may be damaged when taking out the ice. Whirl the
Auger left and right after it has been whirled to ensure normal installation.
1. Choose the ice/ water button on the display board, select entire or crushed
ice pieces and make sure the relevant indicator turns on.
2. Use the container to push and hold the switch plate to get ice.
3. According to the water supply condition, some mixed small ice pieces may
come out when getting the entire ice pieces..
4. When crushed ice pieces are required, please press the container most
close to the ice discharging orice to prevent the crushed ice from
dropping out.
5. When getting ice, the noises of motor, crushing ice and so on are normal.
6. To protect the motor, the refrigeratory will stop when the switch plate is
pushed for 1 minute or more. Then, releasing the switch plate and waiting
a moment, you can get ice normally again.When large amount of entire ice
pieces are required, please open the door Of freezer, take the ice storage
box out and use the ice in it.

EN - 17
Copyright © 2016, Fast ČR, a. s. 04/2016
Way to replace the lter
1. The lter installed in this refrigeratory is rened by NSF42, which can lter the smell, chlorine and so on in
running water.
2. The replacement cycle of the lter is about 6 mouths. When replacement is needed, the indicator on the
display board will turn on. The replacement cycle may be shortened according to operating environment.
3. With the function of BY-PASS, it can supply water normally without the lter. If necessary, additional lter
can be installed and used out of the refrigeratory by yourself.
4. During replacement, little water in the connection part may drop out, a container can be located under it
to receive the drops.
5. The lter is installed in the liner of the refrigerator. You can seize the lower bugle and whirl it leftward
to take it out. When it is dicult to take out, you can detach the lampshade in the refrigerator before
detaching the lter.
6. The assembling is in opposite order. Push it upwards and whirl it rightward at the same time.

EN - 18
Copyright © 2016, Fast ČR, a. s. 04/2016
PART 9: INTRODUCTION OF FUNCTION
See the following gure for keys and display conguration of man-machine interface (Operation interface is
subject to material object)
Display Control
Power on the display panel to reach full display after 3s, the start-up tone rings and the panel displays the sys-
temic memory mode and temperature settings. This is a lock mode. The factory default memory status of main
control board: temperature of refrigerating chamber and freezing chamber is set to 5 °C and -18°C respectively;
there is no setting for special mode; the ice-maker is o by default. After the operation of display panel, the
status is changed and memorized to main control board.
In normal cases, display screen enters standby state and then dies out after display board is locked without
operation of door opening and key operations for 30s.
Where there are key operation, communication failure, sensor failure and ice-making malfunction when the
door is opened, the display screen will light up and prompt relative information. Numeric area displays the
temperature settings of all chambers; when a communication failure occurs, the area of freezing temperature
gives a prompt of communication failure; when a sensor failure occurs, the area of freezing temperature give a
prompt of all fault codes in turns under the lock state; in unlock state, the unlock pattern lights up; in lock state,
the lock pattern lights up. To operate the unlocked keys under the lock state (except option key of ice water
and lter reset), the lock pattern will ash lights.
Key Operation
FRZ.TEMP.: Freezing temperature key
REF.TEMP.: Refrigerating temperature key
MODE.SEL: Option Key of Function
LOCK/UNLOCK: Lock/Unlock Key
ICE OFF: Ice-maker On/O Key
DISPENSER: Option Key of Ice Water
1. LOCK/UNLOCK
Hold “LOCK/UNLOCK” key for 2s under the unlock state, the system enters the lock state; hold “LOCK/
UNLOCK”key for 2s under the lock state, the system enters the unlock state.
In unlocking, the unlock pattern lights up; in locking, the lock pattern lights up.
To operate the unlocked keys under the lock state (except option key of ice water and lter reset), the lock
pattern will ash lights.