Philips AC4372 User manual

Always there to help you
Register your product and get support at
www.philips.com/welcome
Question?
Contact
Philips
AC4372
AC4374
EN User Manual 3
ID Buku Petunjuk Pengguna 22
TH  42
ZH-HK 使用手冊 61

3
EN
English
Contents
1 Important 4
Safety 4
2 Yourairpurier 6
Overview (for AC4372) 6
Overview (for AC4374) 7
3 Get started 8
Install lters 8
4 Usetheairpurier 10
Understand the air quality light 10
Switch on 10
Set the sensitivity of the air quality
sensor 11
Select the fan speed 11
Set the timer 12
Activate child lock 12
Night mode 12
5 Cleanyourairpurier 13
Clean the air purier 13
Clean the air quality sensor 13
6 Cleanthepre-lter 14
7 Replacethelters 16
Reset lter lock 18
8 Troubleshooting 19
9 Guarantee and service 20
Order parts or accessories 20
10 Notices 21
Electromagnetic elds (EMF) 21
Recycling 21

4
EN
1 Important
Safety
Read this user manual carefully
before you use the appliance, and
save it for future reference.
Danger
• Do not let water or any other
liquid or ammable detergent
enter the appliance to avoid
electric shock and/or a re
hazard.
• Do not clean the appliance
with water, any other liquid,
or a (ammable) detergent to
avoid electric shock and/or a re
hazard.
Warning
• Check if the voltage indicated
on the bottom or indicated
at the rear of the appliance
corresponds to the local power
voltage before you connect the
appliance.
• If the power cord is damaged,
you must have it replaced
by Philips, a service center
authorized by Philips, or similarly
qualied persons in order to
avoid a hazard.
• Do not use the appliance if the
plug, the power cord, or the
appliance itself is damaged.
• This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experiences and knowledge if
they have been given supervision
or instruction concerning use of
the appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made
by children without supervision.
• Do not block the air inlet and
outlet, e.g. by placing items on
the air outlet or in front of the
air inlet.
Caution
• This appliance is not a substitute
for proper ventilation, regular
vacuum cleaning, or use of an
extractor hood or fan while
cooking.
• If the power socket used to
power the appliance has poor
connections, the plug of the
appliance becomes hot. Make sure
that you plug the appliance into a
properly connected power socket.

5
EN
English
• Always place and use the
appliance on a dry, stable, level,
and horizontal surface.
• Leave at least 20cm free space
behind and on both sides of
the appliance and leave at least
30cm free space above the
appliance.
• Do not place anything on top of
the appliance and do not sit on
the appliance.
• Do not place the appliance
directly below an air conditioner
to prevent condensation from
dripping onto the appliance.
• Make sure all lters are properly
installed before you switch on
the appliance.
• Only use the original Philips
lters specially intended for this
appliance. Do not use any other
lters.
• Avoid knocking against the
appliance (the air inlet and outlet
in particular) with hard objects.
• Do not insert your ngers or
objects into the air outlet.
• Do not use this appliance when
you have used indoor smoke-
type insect repellents or in
places with oily residues, burning
incense, or chemical fumes.
• Do not use the appliance near
gas appliances, heating devices
or replaces.
• Always unplug the appliance
after use and before you clean it.
• Do not use the appliance in a
room with major temperature
changes, as this may cause
condensation inside the
appliance.
• To prevent interference, place
the appliance at least 2m away
from electrical appliances that
use airborne radio waves such as
TVs, radios, and radio-controlled
clocks.
• The appliance is only intended
for household use under normal
operating conditions.
• Do not use the appliance in wet
surroundings or in surroundings
with high ambient temperatures,
such as the bathroom, toilet, or
kitchen.
• The appliance does not remove
carbon monoxide (CO) or
radon (Rn). It cannot be used a a
safety device in case of accidents
with combustion processes and
hazardous chemicals.

6
EN
2 Your air purifier
Congratulations on your purchase, and welcome to Philips!
To fully benet from the support that Philips offers, register your product at www.philips.com/welcome.
Philips VitaShield IPS technology and NanoCloud technology ensures you “Healthy air always”.
VitaShield IPS technology effectively removes pollutants (ultrane particles, allergens, bacteria and
viruses) with size >0.02 micron including bacteria and virus*.
*According to 2008 Microbiological Risk Assessment Report of the World Health Organization
(WHO), the avian inuenza, human inuenza viruses, Legionella, Hepatitus viruses and SARS
coronavirus are larger than 0.02 micron.
Read this user manual carefully before you install and use the unit. Save it for future reference.
Overview (for AC4372)
a
b
c
d
e
Touchscreen control panel
Light sensor
Air quality light
Air quality sensor
Filter 4: HEPA lter AC4154
f
g
h
i
Filter 3: Activated carbon lter AC4153
Filter 2: Multi-care lter AC4151
Filter 1: Pre-lter
Front panel
d
b
c
e f g h i
a

7
EN
English
Overview (for AC4374)
a
b
c
d
Touchscreen control panel
Light sensor
Air quality light
Air quality sensor
e
f
g
Filter 2: Integrated Multi-care lter AC4138
Filter 1: Pre-lter
Front panel
d
b
c
e f g
a

8
EN
3 Get started
Installlters
The appliance comes with all lters tted
inside, but you have to remove the packaging
of the lters before you can use the appliance.
Remove all lters, unpack them, and place them
back into the appliance as described below.
Note
• Insert the lters in the correct position.
1 Place your ngers in the recesses of the
side panels and gently pull the top part of
the front panel towards you.
2 Lift the hooks at the bottom of the panel
out of the bottom of the appliance.
3 To remove the pre-lter, grab the two
projections and pull the lter towards you.
4 Remove all the lters from the appliance.
5 Remove all packaging material from the
lters.
6 For AC4372, put the HEPA lter, activated
carbon lter and multi-care lter back into
the purier.

9
EN
English
For AC4374, put the integrated Multi-care lter
back into the purier.
Note
• Make sure that the side with the tag is pointing towards
you.
7 Place the pre-ler in the appliance.
2
1
Note
• Make sure that the side with the two projections is
pointing towards you, and that all hooks are properly
attached to the appliance.
8 To reattach the front panel, insert the
bottom hooks into the bottom of the
appliance rst (1). Then, push the panel
against the body of the appliance (2).

10
EN
4 Use the air
purifier
Understand the air quality
light
Color of the air quality
light
Air quality level
Blue Very good
Dark purple Good
Purple Fair
Red Bad
The air quality light automatically goes on when
the purier is switched on.
Note
• The built-in air quality sensor measures the air quality
and automatically selects the appropriate color of
the air quality light. When the air is clean, the color
of the air quality light is in blue. When the air quality
deteriorates, the color of the air quality light changes
from dark purple to red.
Switch on
1 Put the plug of the air purier into the
power socket.
» All lights go on from left to right in
cycle, and you hear a beep.Then, the
lights go out again.
» The air quality light shows 4 colors
successively.
2 Press the button to switch on the
purier.
» The fan speed indicators and
goes on.
Note
• When the purier is switched on, the air quality
sensor will take some time to measure the air quality
in the room.The air quality light changes its color and
eventually stays in the correct color in accordance with
the air quality..
3 Press and hold the button for
2 seconds to switch off the purier.
2”
Tip
• The purier has a memory mode. It will recall the
previous settings of your last use.
• If you disconnect the purier from the power supply
after switching off, it will enter the default mode for
next use.The fan speed is .

11
EN
English
Set the sensitivity of the air
quality sensor
To meet different needs when you use the
appliance, we are offering you the opportunity
to adjust the sensitivity of the air quality sensor.
There are 3 sensitivity levels:
• standard
• sensitive
• extra sensitive
The pollution sensor is set to extra sensitive.
You can adjust the sensitivity of the air quality
sensor in the following way.
Note
• When it is set to a higher sensitivity, the purier
becomes more allergic to the pollutants in the air.
When the purier is in mode, it is more likely
to choose a higher fan speed than the standard mode.
1 Unplug the air purier from the power
socket.
2 Wait for a while before putting the plug
back into the power socket.
3 Press the and buttons simultaneously.
» The purier beeps twice and one of
the fan speed indicators ( , or )
ashes to show the current sensitivity
level of the air quality sensor.
Fan speed
indicator
Sensitivity level
Extra sensitive (default
sensitivity)
Sensitive
Standard
4 Press the button to adjust the sensitivity
level of the air quality sensor.
» One of the indicators ( , , or
) goes on to show the preferred
sensitivity level of the air quality sensor.
5 Press and hold the button for 3 seconds
to switch off the purier, and the sensitivity
setting is saved.
Note
• When setting the sensitivity, if no button is pressed in
10 seconds, the purier will skip the sensitivity setting
mode, and maintain the previous setting.
Select the fan speed
Note
• After you change the sensitivity, the purier
automatically starts operating at the set sensitivity level
whenever you switch on the purier.
You can select the desired fan speed.
1 Press the button once or more times
to select the desired fan speed ( ,
, , , , or ).

12
EN
Set the timer
With the timer function, you can let the purier
operate for a set number of hours. When the
set time has elapsed, the purier automatically
switches off.
1 Press the button to activate the timer.
» The timer indicator ( , , or )
goes on.
2 Press the button repeatedly to choose
the number of hours you want the purier
to operate.The corresponding indicator
(, , or ) goes on.
To deactivate the timer function, press the
button repeatedly until the indicator ( ,
, or ) is out.
Activate child lock
You can activate the child lock function.
1 Press and hold the button for
3 seconds to activate the child lock.
» The child lock indicator lights up.
3”
2 Press and hold the button again for
3 seconds to deactivate the child lock.
3”
Note
• When the child lock function is activated, all buttons are
locked except the button.There will be no audio
feedback when you press the buttons.
Night mode
The purier works in harmony with its
surroundings. The purier automatically switches
to night mode in 3 minutes when the room in
which it is operating becomes dark. All the lights
on the control panel slowly go out.You can
touch any buttons on the control panel during
this period, and the lights go back on. However,
they will go out again in 5 seconds if the purier
is in idle.
If the room becomes bright again for
5 minutes or longer, the purier resumes
normal operation.

13
EN
English
5 Clean your air
purifier
Tip
• You could use the concave of the air quality light as a
handle to lift the purier up.
Note
• Always unplug the purier before you clean or move it.
• Never immerse the purier in water or any other liquid.
• Never use abrasive, aggressive, or ammable cleaning
agents such as bleach or alcohol to clean any part of
the purier.
• Only the pre-lter is washable. Other air purier lters
are not washable nor vacuum cleanable.
Cleantheairpurier
Regularly clean the inside and outside of the
purier body to prevent dust from collecting.
1 Wipe away dust with a soft dry cloth from
the body of the purier.
2 Clean the air inlet and the air outlet with a
soft dry cloth.
Clean the air quality sensor
Clean the air quality sensor every 2 months for
optimal functioning of the purier. Clean it more
frequently if you use the purier in a dusty
environment.
Note
• When the humidity level in the room is very high, it is
possible that condensation develops on the air quality
sensor. As a result, the air quality light may indicate that
the air quality is bad even though it is good. In this case
you have to clean the air quality sensor or use one of
the manual speed settings.
1 Clean the air quality sensor inlet and the
air quality sensor outlet with a soft brush.
2 Remove the air quality sensor cover.
3 Clean the air quality sensor, the dust inlet
and the dust outlet with a lightly moistened
cotton swab.
4 Dry them with a dry cotton swab.
5 Reattach the air quality sensor cover.

14
EN
6 Clean the pre-
filter
Note
• The pre-lter is washable.
• Clean the pre-lter for every two weeks to ensure
optimal functioning of the purier.
• When the pre-lter needs cleaning, the
goes on.
1 Switch off the purier and unplug it.
2 Place your ngers in the recess of the
side panels and gently pull the top part of
the front panel towards you.Then lift the
hooks at the bottom of the panel out of
the top of the purier.
3 To remove the pre-lter, grab the two
projections and pull the lter towards you.
4 Use a vacuum cleaner or wash the pre-
lter under a running tap. If the pre-lter is
very dirty, use a soft brush to brush away
the dust.
5 Air dry the pre-lter.
6 Put the pre-lter back into the purier.
Attach all hooks properly to the purier.
2
1
7 To reattach the front panel, insert the
bottom hooks into the bottom of the
purier rst (1). Then, push the panel
against the body of the purier (2).

15
EN
English
8 Plug the air purier into the power socket
and press the button to switch on the
purier.
9 Press and hold the button for
3 seconds to reset the lter lifetime.
» go off.
3s
Note
• Make sure that the pre-lter is completely dry. If it is still
wet, bacteria may multiply in it and shorten the lifetime
of the pre-lter.
• Make sure that the side with the two projections is
pointing towards you, and that all hooks of the pre-lter
are properly attached to the purier.

16
EN
1 Switch off the purier and unplug it.
2 Place your ngers in the recesses of the
side panels and gently pull the front panel
towards you.Then lift the panel off the
hooks at the bottom of the purier.
3 To remove the pre-lter, grab the two
projections and pull the lter towards you.
4 For AC4372, remove the multi-care lter,
activated carbon lter and HEPA lter
from the purier.
7 Replace the
filters
The indicator of the lter replacement
indicates the respective lters ( , , or )
have to be replaced.
Note
• Lifetime of the lter is based on the volume of air
puried, it may differ from the way of using. In heavily
polluted environment, the lter lifetime may be shorter
than the recommended time.
• If you remove the front panel for lter changing while
the purier is switched on, all lights on the control
panel will be off.
• Once the front panel is placed back to the purier, it
starts to run as its previous status .
• The replaceable lters are not washable nor vacuum
cleanable.
For AC4372
Replace the multi-care lter, the activated
carbon lter, and the HEPA lter when the
respective indicators ( , , and )go on.
For AC4374
Replace the integrated Multi-care lter when
the respective indicator ( )goes on.
This will last for approximately 2 weeks.
On the last day of the 2 weeks, the purier
beeps every 30 minutes to inform you that the
lter needs to be replaced.
Note
• Insert the lters in the correct position.
• For AC4372, make sure you place the lters in the
order of HEPA lter, the activated carbon lter, the
multi-care lter, and then pre-lter.
• For AC4374, make sure you place the lters in the
order of integrated Multi-care lter, and then pre-lter.
• Make sure that the side with the tag is pointing towards
you.

17
EN
English
For AC4374, put the integrated Multi-care
lter back into the purier.
8 Put the pre-lter back into the purier.
2
1
For AC4374, remove the integrated Multi-
care lter from the purier.
5 Take the used lter by the two sides and
deposit it gently into the household trash
bin.
Note
• Do not touch the pleated lter surface, or smell the
lter as it has collected pollutants from the air.
• Wash your hands with tap water and soap after you
have touched the used lter.
6 Remove all packaging material from the
new lters that need replacement.
7 For AC4372, put the HEPA lter, activated
carbon lter and multi-care lter back into
the purier.

18
EN
Resetlterlock
After 2 weeks of lter replacement alert,
and the lters are still not replaced. Then, the
purier will not work until the lter is replaced
and the lter lock is reset.
The goes on along with the lter
replacement indicators ( , , ,
and ). All indicators are off except
if it has been activated. , ,
and buttons remain active, while and
buttons are deactive. See “Replace the lters”
section to reset the lter lock.
9 To reattach the front panel, insert the
bottom hooks into the bottom of the
purier rst (1). Then, push the panel
against the body of the purier (2).
10 Press and hold the button for
3 seconds to reset the lter lifetime.
» For AC4372: , , , and
go off.
3s
» For AC4374: and go off.
3s

19
EN
English
8 Troubleshooting
This chapter summarizes the most common problems you could encounter with the purier. If you are
unable to solve the problem with the information below, contact the Consumer Care Center in your
country.
Problem Possible solution
The , , ,
indicators has been on
continuously.
The lter is full. Replace the lter and reset the purier.
No air comes out of the air
outlet.
The purier is not connected to the power supply. Plug the purier into
the power supply and switch on.
The fan speed does not
change when the
mode is activated.
In mode, the fan speed is set to a very low level. If you want to
change the fan speed, press the button one or more times to set the
desired fan speed.
The airow that comes
out of the air outlet is
signicantly weaker than
before.
• The pre-lter is dirty. Clean the pre-lter (see ‘Clean the pre-lter’).
• You have not removed all packaging material from the lters. Make
sure that you have removed all packaging material.
The air quality does not
improve, even though the
purier has been operating
for a long time.
• One of the lters has not been placed in the purier. Make sure that
all lters are properly installed in the following order, starting with the
innermost lter: For AC4372: HEPA lter (4), activated carbon lter
(3), multi-care lter (2) and pre-lter (1). For AC4374: Integrated
Multi-care lter (2), pre-lter (1).
• The air quality sensor is wet.The humidity level in your room is high
and causes condensation. Make sure that the air quality sensor is clean
and dry (see ‘Clean the air quality sensor’).
The color of the air quality
light always stays the same.
• The air quality sensor is dirty. Clean the air quality sensor (see ‘Clean
the air quality sensor’).
I need cleaner air because I
have an allergy.
You can change the air quality sensor sensitivity (see 'Set the sensitivity
of the air quality sensor’) to make the purier clean the air even better.
The purier is extra loud. • Please check if you have removed all the packaging material from the
lters.
• If the appliance is still too loud; you can change the fan speed to a
lower fan speed level.
The purier still indicates
that I need to replace a lter,
but I already did.
Perhaps you did not press the button to reset the lter lock properly.
Plug in the purier, press the button and press and hold the
button for 3 seconds.

20
EN
9 Guarantee and
service
If you need information or if you have a
problem, please visit the Philips website at
www.philips.com or contact the Philips
Consumer Care Center in your country (you
will nd its phone number in the worldwide
guarantee leaet). If there is no Consumer Care
Centre in your country, go to your local Philips
dealer.
Order parts or accessories
If you have to replace a part or want to
purchase an additional part, go to your Philips
dealer or visit www.philips.com/support.
If you have problems obtaining the parts, please
contact the Philips Consumer Care Center in
your country (you will nd its phone number in
the worldwide guarantee leaet).