Philips HR 4340/A User manual

Air Cleaner
HR 4340/A
Philips Domestic Appliances and Personal Care
Service Manual 4822 729 21616 herewith cancells.
PRODUCT INFORMATION
GENERAL
The HR 4340 is suitable for rooms / areas with a floor surface of
up to approx. 40 m2.
The air cleaner cleans the air effectively by catching 90% of the
gases and 95% of the particles produced by smoking.
This is done by 3 filters :
Foam pre-filter : The foam pre - filter catches the larger
dust particles floating in the air such as
fluff and hairs.
HEPA filter HR4940 : This filter takes out all smaller airborne
particles.
Carbon filter : The carbon filter with activated carbon
granulates (HR4941) effectively absorbes
the smoke gases.
Product meets the requirements regarding interference
suppression on radio and T.V.
FEATURES
Filter full indicator: Indicates that the filter has to be replaced.
This has to be done when the white part of the indicator has
turned pink like the other (pink) half.
Speed control: With 3 speed settings.
Safety lock: Prevents the customer from opening the front
cover whilst the air cleaner is switched on.
The front cover can only be opened, if the switch has been set to
the “0" position.
Overheating safety device: The overheating safety device
comes into operation when the motor becomes too hot. To
indicate that the appliance is still in “ON” position and connected
to the mains, the pilot light remains on.
If this happens : −Switch off the motor.
−After approx. 15 min. the air cleaner can be
switched on again.
TECHNICAL DATA
Voltages : 100 Volt : 95 Watts
110 - 120 Volt : 95 Watts
220 - 240 Volt : 95 Watts
Filters : 2 carbon filters
Life time filters : carbon filters : 3 months
Hepa filter : 6 months
Flow rate : 160 m3/hr
Surface filter surface : 1 m2
Room / area size : Max. 40 m2
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands ©Copyright reserved Subject to modification
4822 729 21809
97/03
PCS 88 615

1) The motor makes an irritating noise.
Check if : −The carbon filters are positioned properly in
the air cleaner.
:−The filters have to be cleaned or replaced.
:−The fan can be rotated freely by hand.
Only for the HR4340/A appliances, which have been
produced before week 9618.
If the motor still makes an irritating noise after the above
checks, the complete product should be replaced by a
sample, produced after week 9618.
2) The overheating device comes into operation.
Check : If the filters are not blocked and nothing is
obstructing the air inlet and air outlet openings.
: That the fan can be moved freely by hand.
In case the problem still remains, replace motor (item 13.0)
and belonging buffers (item 13.1).
POS DESCRIPTION SERVICE CODE
1 FRONT COVER 4822 442 00118
containing : frame 1
foam pre-filter 11
cover 100
2 CONTAINER CARBON GRANULES 4822 418 10132
3 HEPA FILTER HR4940 4822 480 10085
4 CONTROL PANEL 4822 466 10864
5 SWITCH KNOB 4822 410 10261
containing : switch knob 5
spring 101
6 SAFETY LOCK 4822 417 11271
containing : safety lock 6
spring 102
7 PILOT LAMP 220 - 240 V 4822 134 10012
PILOT LAMP 100 - 127 V 4822 134 10013
containing : lamp 7
lamp cover 103
8 SWITCH 4822 273 10304
9 AIR OUTLET 4822 458 10463
10 FRONT HOUSING 4822 441 11656
consisting of : front housing 10
hole plug 105
safety grill 106 2x
foot 107 2x
11 FOAM PRE-FILTER 4822 480 10086
12 FAN 4822 361 10778
containing : fan 12
lock washer 108
washer 109
nut M6 110
nut cover 111
13.0 MOTOR 220 - 240 V 4822 361 10779
MOTOR 110 - 120 V 4822 361 10781
MOTOR 100 V 4822 361 10782
13.1 SET BUFFERS 4822 310 10648
containing: rubber buffers 112 3x
metal bracket 113 3x
bush 115 3x
14 REAR HOUSING 4822 441 11657
consisting of: rear housing 14
foot 107 2x
15 REAR COVER 4822 442 00119
16 CARBON GRANULES HR 4941 4822 390 10139
17 CAPACITOR 110 - 127 V 4822 123 14028
MAINTENANCE
Pre-filter : Wash or vacuum clean the foam pre-filter at
least every 2 months. Fluff and / or hairs can
also be removed by using a soft brush.
Replacement filters are available under service
code 4822 480 10086
NEVER USE WET FILTERS.
HEPA filter : For a proper operation, replace this filter at
least every six months.
Replacement HEPA filters are available under
number HR 4940 and service code
4822 480 10085.
Carbon filter: Replace the carbon granules at least every
3 months.
New carbon granules are available under type
number HR 4941 and service code
4822 390 10139
POSSIBLE COMPLAINTS PARTS LIST HR 4340/A
N.B. PARTST, WITH NUMBERS FROM 100
UPWARDS, CANNOT BE ORDERED
SEPARATELY.
PCS 88 616