Philips TDA1517 User manual

DATA SHEET
Product specification
Supersedes data of 1998 Apr 28
File under Integrated Circuits, IC01
2002 Jan 17
INTEGRATED CIRCUITS
TDA1517; TDA1517P
2×6 W stereo power amplifier

2002 Jan 17 2
Philips Semiconductors Product specification
2×6 W stereo power amplifier TDA1517; TDA1517P
FEATURES
•Requires very few external components
•High output power
•Fixed gain
•Good ripple rejection
•Mute/standby switch
•AC and DC short-circuit safe to ground and VP
•Thermally protected
•Reverse polarity safe
•Capability to handle high energy on outputs (VP=0V)
•No switch-on/switch-off plop
•Electrostatic discharge protection.
GENERAL DESCRIPTION
The TDA1517 is an integrated class-B dual output
amplifier in a plastic single in-line medium power package
with fin (SIL9MPF) and a plastic heat-dissipating dual
in-line package (HDIP18). The device is primarily
developed for multi-media applications.
QUICK REFERENCE DATA
ORDERING INFORMATION
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
VPsupply voltage 6.0 14.4 18.0 V
IORM repetitive peak output current −−2.5 A
Iq(tot) total quiescent current −40 80 mA
Isb standby current −0.1 100 µA
Isw switch-on current −−40 µA
|ZI|input impedance 50 −−kΩ
P
ooutput power RL=4Ω; THD = 0.5% −5−W
RL=4Ω; THD = 10% −6−W
SVRR supply voltage ripple rejection fi= 100 Hz to 10 kHz 48 −−dB
αcs channel separation 40 −−dB
Gvclosed loop voltage gain 19 20 21 dB
Vno(rms) noise output voltage (RMS value) −50 −µV
T
ccrystal temperature −−150 °C
TYPE
NUMBER PACKAGE
NAME DESCRIPTION VERSION
TDA1517 SIL9MPF plastic single in-line medium power package with fin; 9 leads SOT110-1
TDA1517P HDIP18 plastic heat-dissipating dual in-line package; 18 leads SOT398-1

2002 Jan 17 3
Philips Semiconductors Product specification
2×6 W stereo power amplifier TDA1517; TDA1517P
BLOCK DIAGRAM
Fig.1 Block diagram.
handbook, full pagewidth
mute/stand-by
switch input
MLC351
output 1
15 kΩ
15 kΩ
x 1
VA
stand-by
switch
VP
mute
switch
stand-by
reference
voltage
18 kΩ
18 kΩ
2
kΩ
60
kΩ
mute switch Cm
power stage
4
8
mute switch
VA
VA
Cm
2
kΩ
60
kΩ
power stage
6
275
SGND
signal
ground
PGND
output 2
non-inverting
input 1
non-inverting
input 2 9
supply voltage
ripple rejection
output
3
1
TDA1517
mute
reference
voltage
input
reference
voltage
VP
power
ground
(substrate)

2002 Jan 17 4
Philips Semiconductors Product specification
2×6 W stereo power amplifier TDA1517; TDA1517P
PINNING
SYMBOL PIN DESCRIPTION
−INV1 1 non-inverting input 1
SGND 2 signal ground
SVRR 3 supply voltage ripple rejection output
OUT1 4 output 1
PGND 5 power ground
OUT2 6 output 2
VP7 supply voltage
M/SS 8 mute/standby switch input
−INV2 9 non-inverting input 2
Fig.2 Pin configuration for SOT110-1.
n
dbook, halfpage
MLC352
1
2
3
4
5
6
7
8
9
P
V
OUT2
SGND
INV1
INV2
TDA1517
OUT1
M/SS
SVRR
PGND
Fig.3 Pin configuration for SOT398-1.
Pins 10 to 18 should be connected to GND or floating.
n
dbook, halfpage
MLC353
1
2
3
4
5
6
7
8
9
18
17
16
15
14
13
12
11
10
P
V
OUT2
SGND
INV1
INV2
TDA1517P
OUT1
M/SS
SVRR
PGND
FUNCTIONAL DESCRIPTION
The TDA1517 contains two identical amplifiers with
differential input stages. The gain of each amplifier is fixed
at 20 dB. A special feature of the device is the
mute/standby switch which has the following features:
•Low standby current (<100 µA)
•Low mute/standby switching current
(low cost supply switch)
•Mute condition.

2002 Jan 17 5
Philips Semiconductors Product specification
2×6 W stereo power amplifier TDA1517; TDA1517P
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 60134).
THERMAL RESISTANCE
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
VPsupply voltage operating −18 V
no signal −20 V
VP(sc) AC and DC short-circuit safe voltage −18 V
VP(r) reverse polarity −6V
ERGOenergy handling capability at outputs VP=0V −200 mJ
IOSM non-repetitive peak output current −4A
I
ORM repetitive peak output current −2.5 A
Ptot total power dissipation see Fig.4 −15 W
Tstg storage temperature −55 +150 °C
Tamb operating ambient temperature −40 +85 °C
Tccrystal temperature −150 °C
SYMBOL TYPE NUMBER PARAMETER VALUE UNIT
Rth j-c TDA1517 thermal resistance from junction to case 8 K/W
Rth j-p TDA1517P thermal resistance from junction to pins 15 K/W
Rth j-a TDA1517; TDA1517P thermal resistance from junction to ambient 50 K/W
Fig.4 Power derating curve.
(1) Rth j-c = 8 K/W.
(2) Rth j-p = 15 K/W.
handbook, halfpage
25 0 50 150
12
0
MLC354
100
T ( C)
o
amb
P
(W)
18
6
(1)
(2)

2002 Jan 17 6
Philips Semiconductors Product specification
2×6 W stereo power amplifier TDA1517; TDA1517P
DC CHARACTERISTICS
VP= 14.4 V; Tamb =25°C; measured in Fig.6; unless otherwise specified.
Note
1. The circuit is DC adjusted at VP= 6 to 18 V and AC operating at VP= 8.5 to 18 V.
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supply
VPsupply voltage note 1 6.0 14.4 18.0 V
Iq(tot) total quiescent current −40 80 mA
VODC output voltage −6.95 −V
Mute/standby switch
V8switch-on voltage level see Fig.5 8.5 −−V
Mute condition
VOoutput signal in mute position VI(max) =1V;f
i=20Hzto15kHz −−2mV
Standby condition
Isb DC current in standby condition −−100 µA
Vsw switch-on current −12 40 µA

2002 Jan 17 7
Philips Semiconductors Product specification
2×6 W stereo power amplifier TDA1517; TDA1517P
AC CHARACTERISTICS
VP= 14.4 V; RL=4Ω; f = 1 kHz; Tamb =25°C; measured in Fig.6; unless otherwise specified.
Notes
1. Output power is measured directly at the output pins of the IC.
2. Frequency response externally fixed.
3. Ripple rejection measured at the output with a source impedance of 0 Ω, maximum ripple amplitude of 2 V (p-p) and
a frequency between 100 Hz and 10 kHz.
4. Noise voltage measured in a bandwidth of 20 Hz to 20 kHz.
5. Noise output voltage independent of Rs(VI= 0 V).
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Pooutput power THD = 0.5%; note 1 4 5 −W
THD = 10%; note 1 5.5 6.0 −W
THD total harmonic distortion Po=1W −0.1 −%
flr low frequency roll-off at −3 dB; note 2 −45 −Hz
fhr high frequency roll-off at −1dB 20 −−kHz
Gvclosed loop voltage gain 19 20 21 dB
SVRR supply voltage ripple rejection note 3
on 48 −−dB
mute 48 −−dB
standby 80 −−dB
|Zi|input impedance 50 60 75 kΩ
Vno noise output voltage
on Rs=0Ω; note 4 −50 −µV
on Rs=10Ω; note 4 −70 100 µV
mute note 5 −50 −µV
α
cs channel separation Rs=10Ω40 −−dB
|∆Gv|channel unbalance −0.1 1 dB

2002 Jan 17 8
Philips Semiconductors Product specification
2×6 W stereo power amplifier TDA1517; TDA1517P
Fig.5 Standby, mute and on conditions.
handbook, halfpage
8.5
0
MLC355
V
18
6.4
3.3
2
11
(V)
,,,,,,,
,,,,,,,
,,,,,,,
,
,,,,,
,
,
,,,,,
,
,,,,,,,
,,,,,,,
,,,,,,,
ON (I = 40 mA)
P
mute (I = 40 mA)
P
standby (I 100 µA)
P
APPLICATION INFORMATION
Fig.6 Application circuit diagram.
handbook, full pagewidth
MLC356
100 nF
P
V
TDA1517
87
standby switch
220 nF
input 1
1000 µF 1000 µF
input
reference
voltage
2 5
signal
ground power ground
1 9 220 nF input 2
46
3
2200
µF
internal
1/2 VP
100
µF
60 kΩ60 kΩ20 dB 20 dB

2002 Jan 17 9
Philips Semiconductors Product specification
2×6 W stereo power amplifier TDA1517; TDA1517P
PACKAGE OUTLINES
UNIT AA
max.
2A3b1D1
b2 bcD
(1) E(1) Z
max.
(1)
eLPP
1q 1
q
2
q
REFERENCES
OUTLINE
VERSION EUROPEAN PROJECTION ISSUE DATE
IEC JEDEC EIAJ
mm 18.5
17.8 3.7 8.7 8.0
A4
15.8
15.4 1.40 1.14 0.67 0.50 1.40 1.14 0.48
0.38 21.8
21.4 21.4 20.7 6.48 6.20 3.4 3.2
2.54 1.0
5.9
5.7
4.4
4.2
3.9
3.4 15.1 14.9
Q
1.75
1.55
DIMENSIONS (mm are the original dimensions)
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
2.75
2.50
SOT110-1 92-11-17
95-02-25
0 5 10 mm
scale
0.25
w
D
E
A
A
c
A2
3
A4
q1q2
L
Q
wM
b
b1
b2
D1
P
q
1
Ze
19
P
seating plane
pin 1 index
SIL9MPF: plastic single in-line medium power package with fin; 9 leads SOT110-1

2002 Jan 17 10
Philips Semiconductors Product specification
2×6 W stereo power amplifier TDA1517; TDA1517P
UNIT A
max. 12 b
1(1) (1) (1)
b2cD E e M Z
H
L
REFERENCES
OUTLINE
VERSION EUROPEAN PROJECTION ISSUE DATE
IEC JEDEC EIAJ
mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
SOT398-1 94-04-13
95-01-25
A
min. A max. bmax.
w
ME e1
1.40
1.14 0.67 0.50 0.47 0.38 21.85 21.35 6.5 6.2 3.9 3.1 0.252.54 7.62 8.32 8.02 8.7 7.7 1.04.7 0.51 3.7
inches 0.06
0.04 0.03 0.02 0.02 0.01
1.05
0.75
0.04
0.03 0.87 0.84 0.26 0.24 0.15 0.12 0.010.10 0.30 0.33 0.32 0.34 0.30 0.040.19 0.02 0.15
MH
c
(e )
1
ME
wM
b1
b2
e
A
A1
A2
L
seating plane
Z
D
E
18
1
10
9
b
pin 1 index
0 5 10 mm
scale
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
HDIP18: plastic heat-dissipating dual in-line package; 18 leads SOT398-1