Philips HR2860 User manual

HR2860

2

3
1

4

HR2860
ENGLISH 6
 18
 31
 43
 54
 65
 77
 90
 102
 114
 126
 128
 152
 164
 175
 187

6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips offers, register your product at www.philips.
com/welcome.
General description (Fig. 1)
AMains cord
BOn/off button
CMotor unit
DIntegrated blade unit of blender
EBlender beaker
FLid of blender beaker
GRubber sealing ring for blender lid
HStopper
IWet mill beaker
JLid of wet mill beaker
KBlade unit of wet mill
LBuilt-in safety lock
MDry mill beaker
NBlade unit of dry mill
OLid of dry mill beaker
PCord storage
QRubber ring
Important
Read this user manual carefully before you use the appliance and save it
for future reference.
Danger
Never immerse the motor unit in water or any other liquid, nor rinse
it under the tap. Only use a moist cloth to clean the motor unit.
Warning
Check if the voltage indicated on the appliance corresponds to the
local mains voltage before you connect the appliance.
-
-
ENGLISH

Do not use the appliance if the mains cord, the plug or other parts
are damaged.
If the mains cord is damaged, you must have it replaced by Philips, a
service centre authorised by Philips or similarly qualied persons in
order to avoid a hazard.
Never reach into the blender beaker with your ngers or an object
while the appliance is plugged in or operates.The blades are very
sharp.
If the blades get stuck, unplug the appliance before you remove the
ingredients that block the blades.
This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with
the appliance.
Never let the appliance run unattended.
Never use the blender beaker, the dry mill beaker or the wet mill
beaker to switch the appliance on and off.
Do not use the dry mill to grind very hard ingredients such as
nutmeg, Chinese rock sugar and ice cubes
Do not use the wet mill to mix liquids or to crush ice cubes. Use the
blender to process these ingredients.
Do not touch the cutting edges of the blade units when you handle
or clean them.They are very sharp and you could easily cut your
ngers on them.
Caution
Always unplug the appliance before you assemble, disassemble or
make adjustments to the blender, the dry mill or the wet mill
and before you start to clean the appliance.
Never use any accessories or parts from other manufacturers or that
Philips does not specically recommend. If you use such accessories
or parts, your guarantee becomes invalid.
Do not exceed the maximum level indicated on the accessories.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
ENGLISH 7

Do not exceed the maximum quantities and processing times
indicated in the table.
Let hot ingredients cool down before you chop them in the wet mill
or pour them into the blender beaker (max. temperature 80°C).
Never use the dry mill or wet mill for more than 30 seconds without
interruption.
Always process cloves, star anise and aniseed in the dry mill together
with other ingredients. If processed separately, these ingredients may
attack the plastic materials of the dry mill
Do not process dry ingredients such as coffee beans and dried beans
in the wet mill.
Safety features
Built-in safety lock
This feature ensures that you can only switch on the appliance if the
beakers have been placed on the motor unit in the correct position.
When the beakers have been assembled correctly, the built-in safety lock
is unlocked.

The appliance is equipped with a thermal cut-out that automatically cuts
off the power supply to the appliance if it overheats.
If the appliance suddenly stops running:
1 Pull the plug out of the wall socket.
2 Let the appliance cool down for 30 minutes.
3 Put the plug in the wall socket.
4 Switch on the appliance again.
Contact your Philips dealer or an authorised Philips service centre if the
thermal cut-out is activated too often.
To avoid a hazardous situation due to inadvertent resetting of the
thermal cut-out, never connect this appliance to a timer switch.
-
-
-
-
-
ENGLISH8


This Philips appliance complies with all standards regarding
electromagnetic elds (EMF). If handled properly and according to the
instructions in this user manual, the appliance is safe to use based on
scientic evidence available today.

1 Clean all parts except the motor unit (see chapter ‘Cleaning’).
2 Wind excess mains cord round the base of the motor unit (Fig. 2).

Blender
The blender is intended for:
Blending uids, e.g. dairy products, sauces, fruit juices, soups, mixed
drinks, shakes.
Mixing soft ingredients, e.g. almond tea.
1 Put the ingredients in the blender beaker (Fig. 3).
Do not ll the blender beaker beyond the MAX indication.
See the table for the recommended quantities.
Never ll the blender beaker with ingredients that are hotter than
80°C.
Ingredients blender Quantities
fruit 20g
vegetables 100g
vegetable juice 100g vegetables + water (optional)
milkshake 100g fruit + 150ml milk
soy beans 50g soy beans (soaked for 4 hours) +
250ml water
almond tea 75g almonds + 200ml water
-
-
ENGLISH 9

Ingredients blender Quantities
black sesame tea 75g black sesame seeds + 200ml water
2 Press the lid into place.
3 Place the blender beaker on the motor unit (1).Turn the blender
beaker clockwise to fasten it (2) (‘click’) (Fig. 4).
Do not exert too much pressure on the blender beaker.
4 Put the plug in the wall socket and press the on/off button.
Hold the motor unit rmly with both hands when the appliance operates.
Do not operate the blender for more than 1 minute at a time.
If you have not nished blending after 1 minute, switch off the appliance
and wait 1 minute before you continue. If the appliance becomes hot, let
it cool down before you continue.
Never reach into the blender beaker with your ngers or an object (e.
g. a spatula) while the blender operates.
Do not touch the sharp blades. If the blades get stuck, unplug the
appliance and remove the ingredients that block the blades with a
spatula.

To avoid spillage, never ll the blender beaker above the maximum
level indication (0.4 litres).
You can pour liquid ingredients (e.g. oil) into the blender beaker
through the opening in the lid while the appliance operates (Fig. 5).
Cut solid ingredients into smaller pieces (1-2cm) before you put
them in the blender beaker. Do not process a large quantity of solid
ingredients at the same time. Process these ingredients in a series of
small batches instead.
Dry mill
The dry mill is intended for grinding dry ingredients (Fig. 6).
-
-
-
-
ENGLISH10

The dry mill is not suitable for chopping very hard ingredients like
nutmeg.
Do not touch the sharp blades. If the blades get stuck, switch off the
appliance and disassemble the dry mill beaker. Use a spatula to remove
the ingredients that block the blades.
1 Put the dry ingredients in the dry mill beaker (Fig. 7).
Do not ll the dry mill beaker beyond the MAX indication.
See the table for the recommended quantities.
Ingredients dry mill Quantities
nuts 20-25g
cheese 20-50g
coffee beans 20-50g
peppercorns 5-25g
black sesame 20-50g
uncooked rice, wheat 20-50g
sugar cubes 4-8 cubes
bread (for breadcrumbs) one slice of bread
soy beans (dried) 20-50g
tea leaves 20-50g
hard spices (e.g. cloves, cassia) 2g
2 Screw the blade unit of the dry mill (with three blades) onto the
dry mill beaker (Fig. 8).
3 Turn the assembled dry mill upside down and place it on the motor
unit (1).Turn the dry mill clockwise to fasten it (2) (‘click’) (Fig. 9).
4 Put the plug in the wall socket and press the on/off button (Fig. 10).
ENGLISH 11

Hold the motor unit rmly with both hands when the appliance operates.
Do not operate the dry mill for more than 30 seconds at a time.

Always process cloves, star anise and aniseed together with other
ingredients. If processed separately, these ingredients may attack the
plastic materials of the appliance.
Hard spices such as cassia must be cut into pieces smaller than 1 x
2cm.
To use the dry mill beaker as a container, turn it upside down and put
the plastic lid on the dry mill beaker.
Wet mill
The wet mill is intended for chopping moist ingredients such as meat,
onions, garlic etc (Fig. 6).
The wet mill is not suitable for chopping dry ingredients such as coffee
beans and dried beans.
Do not use the wet mill to mix liquids or to crush ice cubes. Use the
blender to process these ingredients.
Do not touch the sharp blades. If the blades get stuck, switch off the
appliance and disassemble the wet mill beaker. Use a spatula to remove
the ingredients that block the blades.
1 Cut the ingredients into smaller pieces (approx. 1-2cm) and put
them in the wet mill beaker. (Fig. 11)
Do not ll the wet mill beaker beyond the MAX indication.
See the table for the recommended quantities.
Ingredients wet mill Quantities
pre-soaked seeds and grains (e.g. lotus
seeds, rice)
20-50g
spice paste ingredients (chilli, onion,
parsley etc.)
50g
-
-
-
-
ENGLISH12

Ingredients wet mill Quantities
garlic 20-50g
onions 20-50g
lean pork meat (without any fat) 20g
2 Turn the assembled wet mill upside down and place it on the
motor unit (1).Turn the wet mill clockwise to fasten it (2)
(‘click’) (Fig. 12).
3 Put the plug in the wall socket and press the on/off button. (Fig. 10)
Hold the motor unit rmly with both hands when the appliance operates.
Do not operate the wet mill for more than 30 seconds at a time.

If the ingredients stick to the wall of the wet mill beaker, switch off
the appliance and disassemble the wet mill beaker. Use a spatula to
loosen the ingredients from the wall (Fig. 13).
If the appliance shakes because the food is not evenly distributed,
switch off the appliance and disassemble the wet mill. Distribute the
ingredients evenly in the wet mill beaker, reassemble the wet mill and
screw it onto the motor unit.Then switch on the appliance again.
To use the wet mill beaker as a container, turn it upside down and
put the plastic lid on the wet mill beaker (Fig. 14).
Cleaning
Cleaning the appliance is easiest immediately after use.
Never immerse the motor unit in water.
Do not touch the cutting edges of the blade units when you handle or
clean them. They are very sharp and you could easily cut your ngers
on them.
Never clean the motor unit, the accessories and the parts in the
dishwasher.
-
-
-
ENGLISH 13

Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the appliance.
Note: Parts of the appliance may become discoloured when the appliance is
used to process ingredients that contain a lot of pigment such as cloves,
anise, cinnamon and tomato paste.This is normal.
1 Unplug the appliance and remove the blender, the dry mill or the
wet mill from the motor unit.
2 Clean the blender, the dry mill or the wet mill in warm water with
some washing-up liquid and rinse them under the tap.
3 If necessary, remove the rubber sealing ring from the blender lid
and rinse it with water.
4 Clean the motor unit with a moist cloth.
Environment
Do not throw away the appliance with the normal household waste
at the end of its life, but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve the
environment (Fig. 15).
Guarantee and service
If you need service or information or if you have a problem, please visit
the Philips website at www.philips.com or contact the Philips Consumer
Care Centre in your country (you nd its phone number in the
worldwide guarantee leaet). If there is no Consumer Care Centre in
your country, go to your local Philips dealer.
-
ENGLISH14


Problem Possible cause Solution
The appliance
does not
work
The appliance is
equipped with a safety
lock. If the blender
beaker dry mill beaker
or wet mill beaker has
not been assembled
properly onto the
motor unit, the
appliance does not
work.
Press the on/off button to
make sure that the appliance
is switched off.Then check
whether the beaker has been
assembled properly (see
chapter ‘Using the appliance’).
The blade
unit or motor
unit is
blocked.
There is too much
food in the beaker.
Switch off the appliance and
process a smaller quantity.
The motor
unit gives off
an unpleasant
smell during
the rst few
times of use.
This is normal. If the appliance continues to
give off this smell after you
have used it a few times,
check whether the processing
quantity and processing time
are correct.
The appliance
makes a lot
of noise,
smells, feels
hot to the
touch, emits
smoke, etc.
There is too much
food in the beaker.
Switch off the appliance and
process a smaller quantity.
ENGLISH 15

Problem Possible cause Solution
You let the appliance
operate too long
without interruption.
Do not operate the blender
for more than 1 minute at a
time. Do not operate the dry
mill and wet mill for more
than 30 seconds at a time.
The lid of the
blender
beaker leaks.
You have not placed
the lid properly.
Make sure the lid of the
blender beaker has been
properly place.
The sealing ring is not
or not properly placed
in the blender beaker
lid.
Put the sealing ring properly
in the blender beaker lid.
There is too much
food in the blender
beaker.
Switch off the appliance and
process a smaller quantity.
The dry or
wet mill
vibrates
strongly,
produces a
lot of noise
or the blade
unit is out of
alignment.
You have not
assembled the blade
unit properly onto the
dry mill or wet mill
beaker.
Screw the blade
unit properly onto the dry or
wet mill beaker.
The food in the dry
mill or wet mill
beaker blocks the
blades.
Remove the food that blocks
the blade and/or process a
smaller quantity.
ENGLISH16

Problem Possible cause Solution
The dry or
wet mill leaks.
The sealing ring is not
or not properly placed
on the blade unit.
Unplug the appliance.
Remove the blade unit and
assemble the rubber
ring properly onto the blade
unit.
ENGLISH 17

18

Поздравления за вашата покупка и добре дошли във Philips! За да се
възползвате изцяло от предлаганата от Philips поддръжка,
регистрирайте продукта си на www.philips.com/welcome.

A Захранващ кабел
B Бутон on/off (вкл./изкл.)
C Задвижващ блок
D Вграден режещ блок на пасатора
E Кана на пасатора
F Капак на каната на пасатора
G Гумен уплътнителен пръстен за капака на пасатора
H Запушалка
I Кана на мелачката за сочни продукти
J Капак на каната на мелачката за сочни продукти
K Режещ блок на мелачката за сочни продукти
L Вградена защитна блокировка
M Кана на мелачката за твърди продукти
N Режещ блок на мелачката за твърди продукти
O Капак на каната на мелачката за твърди продукти
P Отделение за прибиране на кабела
Q Гумен пръстен

Преди да използвате уреда, прочетете внимателно това
ръководство за експлоатация и го запазете за справка в бъдеще.

Не потапяйте задвижващия блок във вода или друга течност и не
го изплаквайте под крана на чешмата. Почиствайте задвижващия
блок само с влажна кърпа.
-



Преди да свържете уреда към мрежата, проверете дали
посоченото върху уреда напрежение отговаря на напрежението
на местната електрическа мрежа.
Не използвайте уреда, ако захранващият кабел, щепселът или
други части са повредени.
Ако захранващият кабел се повреди, той трябва винаги да се
подменя от Philips, упълномощен сервиз на Philips или подобни
квалифицирани лица, за да се избегне опасност.
Никога не бъркайте в каната на пасатора с пръсти или с други
предмети, докато уредът работи или е включен в контакта.
Ножовете са много остри!
Ако ножовете заседнат, изключете уреда от контакта, преди да
отстранявате продуктите, блокирали ножовете.
Този уред не е предназначен за ползване от хора (включително
деца) с намалени физически усещания или умствени недостатъци
или без опит и познания, ако са оставени без наблюдение и не са
инструктирани от страна на отговарящо за тяхната безопасност
лице относно начина на използване на уреда.
Наглеждайте децата, за да не си играят с уреда.
Никога не оставяйте уреда да работи без наблюдение.
Никога не използвайте каната на пасатора, мелачката за твърди
продукти или тази за сочни продукти за включване и изключване
на уреда.
Никога не използвайте мелачката за твърди продукти за смилане
на много твърди продукти, като например индийско орехче,
едрокристална захар (небет-шекер) или ледени кубчета
Не използвайте мелачката за сочни продукти за разбъркване на
течности или за натрошаване на ледени кубчета. За такива
съставки използвайте пасатора.
Не докосвайте остриетата на режещия блок, когато ги сваляте
или почиствате. Те са много остри и лесно можете да порежете
пръстите си..

Винаги изключвайте уреда от контакта, преди да пристъпите към
сглобяване, разглобяване или наместване на пасатора, мелачката
-
-
-
-
-
-
-
-
-
-
-
-
-
 19

за твърди продукти или тази за сочни продукти, както и преди да
започнете да почиствате уреда.
Никога не използвайте аксесоари или части от други
производители или такива, които не са специално препоръчвани
от Philips. При използване на такива аксесоари или части вашата
гаранция става невалидна.
Не превишавайте максималното ниво, показано на
принадлежностите.
Не превишавайте максималните количества и времена за
обработване, посочени в таблицата.
Изчакайте горещите продукти да изстинат, преди да ги кълцате в
мелачката за сочни продукти или изсипвате в каната на пасатора
(макс. температура 80°C).
Не използвайте мелачката за твърди продукти или тази за сочни
продукти за повече от 30 секунди без прекъсване.
Винаги обработвайте скилидките чесън, звездовидния анасон и
анасоновото семе в мелачката за твърди продукти заедно с
другите съставки. Ако се обработват отделно, тези продукти
могат да разядат пластмасовите материали на мелачката за
твърди продукти.
Не обработвайте сухи продукти като кафе и зрял боб в
мелачката за сочни продукти.


Тази функция гарантира, че ще можете да включвате уреда само
когато каните са монтирани на задвижващия блок в правилното
положение. Когато каните са сглобени правилно, вградената защитна
блокировка се освобождава.

Този уред е с термичен прекъсвач, който автоматично изключва
електрозахранването му в случай на прегряване.
Ако уредът внезапно спре да работи:
1 Извадете щепсела на захранващия кабел от контакта.
2 Оставете уреда да се охлажда 30 минути.
-
-
-
-
-
-
-
20