Philips CEM2000/55 User manual

Register your product and get support at CEM2000
EN Quick Start Guide

1ab
efg
45
B
h
d
c
A
b
a
c
d
aa
bcd
ab
ef
cd
gh
b
c
d
32

6
5mm5mm5mm5mm
5mm

Overview of parts 1
These are the supplied parts needed to connect
and install this unit.
aIn-car audio system
b Sleeve
c Front panel
d Standard ISO connector
e Trim plate
f Rubber cushion
g Disassembly tools
h Screws (4 pieces)
Select country/region
1Press
to turn on the unit.
2 Rotate
to select an option:
[USA] (United States)•
[Latin] (Latin America)•
[Europe] (Western Europe)•
[ASIA] (Asia Pacific)•
[Mid-East ] (Middle East)•
[Russia] (Russia)•
3 Press
to confirm.
Connection
Caution
• Ensure that all loose leads are insulated with
electrical tape.
For cars with ISO connectors 234
1Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2Connect the other end of the supplied
standard connector to the unit.
3Connect the antenna and amplifier as
illustrated, if applicable.You can connect the
car audio to the amplifier through RCA-TO-
RCA cables (not supplied).
Connector Connect to
1ANTENNA Antenna
2FRONT LINE
OUT R (Socket)
Front right speaker
3FRONT LINE
OUT L (Socket)
Front left speaker
4REAR LINE
OUT R (Socket)
Rear right speaker
5REAR LINE
OUT L (Socket)
Rear left speaker
6SUBWOOFER Subwoofer
For cars with ISO connectors 45
Caution
• Be sure to connect the black ground (earth)
lead first.
1Connect the antenna and amplifier as
illustrated, if applicable.
2Cut off the bigger end of the supplied
standard connector.
3Check the car’s wiring carefully and connect
them to the supplied standard connector.
4Connect the supplied standard connector to
the unit.
1Green/black strip Left speaker (Rear)
2White/black strip Left speaker (Front)
3Gray/black strip Right speaker (Front)
4Purple/black strip Right speaker (Rear)
eRED Ignition key +12V DC when
ON/ACC
fBLUE Motor/electric antenna relay
control lead/Amplifier relay
control lead
gBLACK Ground
hYELLOW To the +12V car battery
which is energized at all times

Mount in the dashboard 6
1If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in•
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
If the car battery is not disconnected,•
to avoid short-circuit, ensure that bare
wires do not touch each other.
2Remove the two screws on the top of the
unit.
3Remove the mounting sleeve with the
supplied disassembly tools.
4Install the sleeve into the dashboard and
bend the tabs outward to fix the sleeve.
5Place the supplied rubber cushion over the
end of the mounting bolt.
6Slide the unit into the dashboard until you
hear a click sound.
7Reconnect the negative terminal of the car
battery.
Attach the front panel 6
1Attach the trim plate.
2Insert the right side of the panel in the
chassis until it is correctly engaged.
3Press the left side of the panel until the
mechanism locks it into place.
Turn on
1Press
to turn on the unit.
To turn off the unit, press• for over 3
seconds.
Set clock
1Press MENU.
2Press
or repeatedly until currently time
is displayed.
3Tu r n
clockwise to set hour.
4Press
to confirm.
5Tu r n anti-clockwise to set minute.
6Press
to confirm.
View clock
1Press and hold OPTIONS repeatedly until
the clock is displayed.
Listen to radio
1Press SOURCE repeatedly to select Tuner.
2Press
or to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3Press or to tune to a radio station
manually.
The radio station is broadcast.•
To search for a radio station•
automatically, press or for over
3 seconds.

© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: CEM2000_55_QSG_V2.1