Philips CEM2200 User manual

www.philips.com/support
User manual
Always there to help you
Register your product and get support at
CEM2200
Question?
Contact
Philips

1
English
EN
Contents
1 Safety 2
2 Your car audio system 2
Introduction 2
What's in the box 3
Overview of the system 4
3 Install the car audio system 6
Connect wires 7
Mount into the dashboard 8
Attach the front panel 9
4 Get started 10
For the rst time use 10
Set the time format 10
Set the clock 10
Turn on 10
Switch music listening zone 10
Mute the button beep 10
5 Listen to radio 11
Tune to a radio station 11
Store radio stations in memory 11
Tune to a preset station 11
Play with RDS 11
6 Play from hard media 13
Play a disc 13
Play from a USB storage device 13
7 Listen to an external player 15
8 Charge your USB device 15
9 Adjust sound 16
10 Adjust system settings 16
11 Others 17
Reset 17
Replace fuse 17
12 Product information 18
13 Troubleshooting 19
14 Notice 20
Compliance 20
Care of the environment 20
Trademark notice 20
Copyright 20

2EN
1 Safety
Read and understand all instructions before
you use your apparatus. If damage is caused by
failure to follow instructions, the warranty does
not apply.
• This apparatus is designed for negative
ground (earth) 12V DC operation only.
• To ensure safe driving, adjust the volume to
a safe and comfortable level.
• Improper fuses can cause damage or
re. When you need to change the fuse,
consult a professional.
• Use only the supplied mounting hardware
for a safe and secure installation.
• To avoid short circuit, do not expose the
apparatus to rain or water.
• Never insert objects into the ventilation
slots or other openings on the apparatus.
• Clean the apparatus and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the apparatus.
• Never place any objects other than discs
into the apparatus.
• Never use solvents such as benzene,
thinner, cleaners available commercially, or
anti-static sprays intended for discs.
• Visible and invisible laser radiation when
open.Avoid exposure to beam.
Caution
• Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
laser exposure or other unsafe operation.
• The apparatus shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on the
apparatus (e.g. liquid lled objects, lighted
candles).
2 Your car audio
system
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With the in-car audio system, you can listen to
• FM or AM (MW) radio,
• Audio from a CD or MP3 disc,
• Audio from a USB storage device, and
• Audio from an external player.
Playable media:
• Disc
• Audio CD, MP3-CD,WMA-CD
• CD-R, CD-RW
• USB storage device
• Compatibility: USB 2.0, USB 1.1
• Class support: MSC (Mass Storage
Class)
• Maximum capacity: 32 GB
• Files
• File system: FAT16, FAT32
• Maximum number of folders: 99
• Maximum number of tracks/les: 999
• Maximum level of directory: 8
• .mp3 les
Sampling frequencies: 32 kHz, 44.1 kHz,
48 kHz
Bitrates: 8-320 kbps and variable
bitrates
• .wma les
Versions:V4,V7,V8,V9 (L1 and L2)
Sampling frequencies: 44.1 kHz, 48 kHz
Bitrates: 64-192 kbps and variable
bitrates
• ID3 tagV2.0 or later

3
English
EN
• Unsupported les:
AAC, WAV, and PCM les
DRM protected WMA les (.wav, .m4a,
.m4p, .mp4, and .aac)
WMA les in lossless format
What's in the box
Check and identify the contents of your
package:
a Main unit (with a sleeve)
b Carrying case (with the front panel
included)
c Trim plate
d Disassembly tool x 2
e Rubber cushion
f Screw x 1
g User manual
abc
e
df
g

4EN
Overview of the system
a
• Press to enable or disable the DBB
(dynamic bass boost) sound effect.
b
• Unlock the front panel.
c
• Press to return to the previous menu.
• Press and hold to access the system
menu.
d
• Press to turn on the system.
• Press and hold to turn off the system.

5
English
EN
• Press to mute the speakers or release
them from mute status.
• Press to conrm an option.
• Rotate to switch between menu
options.
• Rotate to adjust the volume level.
e
• For .wma and .mp3 tracks, press to
select the previous folder.
• In radio mode, press to select a tuner
band.
• Press and hold to activate the selection
of listening zones.
f
• Eject the disc from the disc
compartment.
g
• Connect to a USB storage device.
h
• Connect to the audio output socket
(usually the headphone socket) of an
external device.
i
• Start, pause, or resume the play of
tracks.
• In radio mode, press to select the
preset radio station of No. 6.
• In radio mode, press and hold to store
the current radio station at channel
No. 6.
j
• In radio mode, press to select the
preset radio station of No. 5.
• In radio mode, press and hold to store
the current radio station at channel
No. 5.
k
• In radio mode, press to select the
preset radio station of No. 4.
• In radio mode, press and hold to store
the current radio station at channel
No. 4.
• For .wma and .mp3 tracks, press
repeatedly to select a play mode: play
all tracks randomly ([SHU ALL]), play
tracks in the current folder randomly
([SHU FLD]), or play all tracks in the
storage device in sequence ([SHU
OFF]).
l
• In radio mode, press to select the
preset radio station of No. 3.
• In radio mode, press and hold to store
the current radio station at channel
No. 3.
• For .wma and .mp3 tracks, press
repeatedly to select a repeat mode:
repeat the current track ([REP ONE]),
repeat all tracks in the current folder
([RPT FLD]), or repeat all tracks in the
storage device ([RPT ALL]).
m
• In radio mode, press to select the
preset radio station of No. 2.
• In radio mode, press and hold to store
the current radio station at channel
No. 2.
• For .wma and .mp3 tracks, press to
access the folder list.
n
• In radio mode, press to select the
preset radio station of No. 1.
• In radio mode, press and hold to store
the current radio station at channel
No. 1.
• For .wma and .mp3 tracks, press to
access the track list.
o /
• Press repeatedly to display available
information about the current track.
• Press repeatedly to display available
RDS information.
• Press and hold to display the set clock.
p /
• Press repeatedly to select a source.

6EN
• In radio mode, press and hold to
activate the automatic search of radio
stations.
q
• For .wma and .mp3 tracks, press to
select the next folder.
• In radio mode, press to select a tuner
band.
r
• Press repeatedly to select a preset
sound equalizer.
• Press and hold to activate the setup of
bass, treble, balance, and fader.
s
• Press to enable or disable the MAX
Sound feature.
t /
• Tune to a radio station.
• Press to skip to the previous or next
track.
• Press and hold to rewind a track or
search fast forward.
u
• Press to reset the system to factory
default settings.
v Disc slot
3 Install the car
audio system
Caution
• Use the controls only as stated in this user manual.
Always follow the instructions in this chapter in
sequence.
These instructions are for a typical installation.
However, if your car has different requirements,
make the adjustment accordingly. If you have
any question regarding installation kits, consult
your local retailer.
Note
• This system is designed for negative ground (earth) 12V
DC operation only.
• Always install this system in the car dashboard. Other
locations can be dangerous as the rear of the system heats
up during use.
• To avoid short-circuit: before you connect, make sure that
the ignition is off.
• Make sure that you connect the yellow and red power
supply leads after all other leads are connected.
• Make sure that all loose leads are insulated with electrical
tape.
• Make sure that the leads do not get caught under screws
or iron parts that will move (e.g. seat rail).
• Make sure that all ground (earth) leads are run to a
common ground (earth) point.
• Use only the supplied mounting hardware for a safe and
secure installation.
• Improper fuses can cause damage or re. When you need
to change the fuse, consult a professional.
• When you connect other devices to this system, make
sure that the rating of the car circuit is higher than the
total fuse value of all the connected devices.
• Never connect speaker wires to the metal body or chassis
of the car.
• Never connect speaker wires with stripes to one another.

7
English
EN
Connect wires
Note
• Consult a professional to connect the unit as instructed
below.
1 Check the car's wiring carefully and
connect them to the the male connector.
ISO male
connectors Connect to
a Green strip, black-
edged green strip
Left speaker (Rear)
b White strip, black-
edged white strip
Left speaker (Front)
c Gray strip, black-
edged gray strip
Right speaker (Front)
d Purple strip, black-
edged purple strip
Right speaker (Rear)
e Red Ignition key +12V
DC when ON/ACC
f Blue Motor/electric
antenna relay control
lead
g White edged blue
strip
Amplier relay
control lead
h Black Ground
i Yellow To the +12V car
battery which is
energized at all times
2 Connect the antenna and amplier as
illustrated, if applicable.
Connector Connect to
1 ANTENNA Antenna
2 Socket for ISO male
connectors
As indicated in
Step 1 above
3 REAR LINE OUT R
(Socket)
Rear right speaker
4 REAR LINE OUT L
(Socket)
Rear left speaker
5 OE REMOTE
(Purple)
OE Remote
6 OE REMOTE
(Black strip)
Ground
Tip
• The pin arrangement for the ISO connectors depends
on the type of vehicle you drive. Be sure to make
proper connections to prevent damage to the unit.

8EN
Mount into the dashboard
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
• If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
• If the car battery is not disconnected,
to avoid short-circuit, ensure that the
bare wires do not touch each other.
2 Ensure that car dashboard opening is
within these measurements:
3 Remove the mounting sleeve with the
supplied disassembly tools.
4 Install the sleeve into the dashboard and
bend the tabs outward to x the sleeve.
183 mm
53mm
5mm
Note
• If the unit is not xed by sleeve but by the supplied
screws, skip this step.
5 Place the supplied rubber cushion over the
end of the mounting bolt.
183 mm
53.5 mm