Philips CMD310 User manual

Register your product and get support at
www.philips.com/welcome
Always there to help you
User manual 1
Manual del usuario 27
Руководство пользователя 57
CMD310
Question?
Contact
Philips

1
English
EN
Contents
1 Important 2
Safety 2
Notice 2
2 Your car audio system 4
Introduction 4
What's in the box 4
Overview of the system 5
3 Before use 7
Install the car audio system 7
4 Get started 10
Turn on 10
Change system settings 10
Set the clock 11
Select a source 11
5 Listen to radio 12
Select a radio region 12
Select a tuner sensitivity 12
Tune to a radio station 12
Store radio stations in memory 12
Tune to a preset station 13
Play with RDS 13
6 Use Bluetooth devices 15
Pair a device 15
Play audio from a Bluetooth device 15
Make a call 15
7 Play from a USB storage device 16
Control play 16
8 Listen to an external device 17
9 Use the dock 17
Compatible iPod/iPhone models 17
Prepare for docking 17
Load your iPhone or iPod touch 18
Adjust the dock bracket 18
Pair your iPhone via Bluetooth 19
Enjoy audio through the dock 19
Use the CarStudio application 20
Charge your iPhone or iPod touch 20
Undock your iPhone or iPod touch 20
Store the dock bracket 21
10 Adjust sound 21
Adjust the volume level 21
Mute sound 21
Use the DBB sound effect 21
Enable the max sound 21
Select a listening zone 21
Enable the full-range sound 22
Select a preset sound equalizer 22
Other sound settings 22
11 Adjust system settings 22
12 Additional information 23
Reset the system 23
Replace the fuse 23
13 Product information 24
14 Troubleshooting 25
General 25
About Bluetooth device 25
15 Glossary 26
Contents

2EN
1 Important
Safety
Read and understand all instructions before you
use the device. If damage is caused by failure to
follow instructions, the warranty does not apply.
• Modicationoftheproductcouldresult
in hazardous radiation of EMC or other
unsafe operation.
• The device is designed for negative ground
(earth) 12V DC operation only.
• Toreducetheriskoftrafcaccidents,do
not pick up or make a phone call, nor
watch video when driving.
• To ensure safe driving, adjust the volume to
a safe and comfortable level.
• Improper fuses can cause damage or
re.Whenyouneedtochangethefuse,
consult a professional.
• Use only the supplied mounting hardware
for a safe and secure installation.
• To avoid short circuits, do not expose the
device, remote control or remote control
batteries to rain or water.
• The device shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on
thedevice(e.g.liquidlledobjects,lighted
candles).
• Never insert objects into the ventilation
slots or other openings on the device.
• Clean the device with soft, damp cloth.
Never use substances such as alcohol,
chemicals or household cleaners on the
device.
• The dock is designed for iPhone and iPod
touch only. Do not connect any other
device to it.
• Risk of damage to the dock bracket: Do
not place or hang any object on it.
• Riskofringordamagetothecaraudio
system: Do not place any other object into
the compartment for dock bracket.
• Risk of damage to your iPhone or iPod
touch: Unload your iPhone or iPod touch
from the dock before you store the dock
bracket.
Notice
Anychangesormodicationsmadetothis
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
Compliance
This product complies with the radio
interference requirements of the European
Community.
Care of the environment
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC. Please inform yourself about the local
separate collection system for electrical and
electronic products.

3
English
EN
Please act according to your local rules and
do not dispose of your old products with your
normal household waste.
Correct disposal of your old product helps to
prevent potential negative consequences for the
environment and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Copyright
2012 © Koninklijke Philips Electronics N.V.
Specicationsaresubjecttochangewithout
notice.Trademarks are the property of
Koninklijke Philips Electronics N.V or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
Trademark notice
The Bluetooth®word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by Philips is
under license.
Windows Media and the Windows logo
are trademarks, or registered trademarks of
Microsoft Corporation in the United States
and/or other countries.
“Made for iPod” and “Made for iPhone”
mean that an electronic accessory has been
designedtoconnectspecicallytoiPodor
iPhonerespectively,andhasbeencertiedby
the developer to meet Apple performance
standards.Apple is not responsible for the
operation of this device or its compliance with
safety and regulatory standards. Please note that
the use of this accessory with iPod or iPhone
may affect wireless performance.
iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries.
Other trademarks and trade names are those
of their respective owners.

4EN
2 Your car audio
system
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this system, you can:
• enjoy audio from USB storage devices,
iPhone, iPod touch, and other external
devices,
• listen to radio stations,
• charge your iPhone or iPod touch, and
• make phone calls.
You can enrich sound output with these sound
effects:
• Dynamic bass boost (DBB)
• Automatic loudness control
Playable media:
• USB storage device
• Compatibility: USB 2.0, USB 1.1
• Class support: MSC (Mass Storage
Class)
• File system: FAT16, FAT32
• Files: .mp3, .wma
• Maximum number of albums/folders:
99
• Maximumnumberoftracks/les:999
• Maximum level of directory: 8
• iPhone and iPod models
• iPhone 4S
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPod touch (3rd and 4th generations)
What's in the box
Check and identify the contents of the package:
a Main unit and front panel (with a sleeve)
b Trim plate
c ISO standard connector
d Rubber cushion
e 1 x Screw
f 2 x Disassembly tools
g User manual
h Quick start guide
a
cd
fe
gh
b
Quick start guide

5
English
EN
Overview of the system
a
• Press to answer or redial a call.
• Press to hang up a call.
b
• Tune to a radio station.
• Press to skip to the previous track.
• Press and hold to rewind a track.
c
• Press to enable or disable the full
sound.
• Press and hold to access the sound
setting menu.
d
• Press repeatedly to select a source.
• Press and hold to activate the selection
of listening zones.
e
• In radio mode, press to select the
preset radio station of No. 1.
• In radio mode, press and hold to store
the current radio station at channel
No. 1.
• For .wma/.mp3 tracks, press to select
the next album/folder.
qrtsu nop
ef
gh
jk l
i
a
b
c
d
m
f
• In radio mode, press to select the
preset radio station of No. 2.
• In radio mode, press and hold to store
the current radio station at channel
No. 2.
• For .wma/.mp3 tracks, press to select
the previous album or folder.
g
• Press to enable or disable the
maximum volume.
• Press and hold to enable or disable
the DBB (dynamic bass boost) sound
effect.
h
• In radio mode, press to select the
preset radio station of No. 3.
• In radio mode, press and hold to store
the current radio station at channel
No. 3.
• For tracks, press to select a repeat
mode: repeat the current track, or
repeat all tracks in the current album
or folder.

6EN
i
• In radio mode, press to select the
preset radio station of No. 4.
• In radio mode, press and hold to store
the current radio station at channel
No. 4.
• For tracks, press to start playing all
tracks in the current album or folder
randomly.
j
• In radio mode, press to select the
preset radio station of No. 5.
• In radio mode, press and hold to store
the current radio station at channel
No. 5.
k
• In radio mode, press to select the
preset radio station of No. 6.
• In radio mode, press and hold to store
the current radio station at channel
No. 6.
• Start, pause, or resume the play of
tracks.
l Dock for iPhone/iPod touch
m MP3-LINK
• Connect to the audio output socket
(usually the headphone socket) of an
external device.
n USB
• Connect to a USB storage device.
o RESET
• Press to reset the system to factory
default settings.
p
• Press to eject the dock bracket.
q LCD screen
r
• Press once to display the system clock.
• Press and hold to access the system
menu.
s
• Press to turn on the system.
• Press and hold to turn off the system.
• Press to mute the system or release it
from mute status.
• Presstoconrmanoption.
• Rotate to switch between menu
options.
• Rotate to adjust the volume level.
t MIC
• Integrated microphone.
u
• Press to exit the current menu.
• Press repeatedly to select a tuner band.
• Press and hold to transfer a call.

7
English
EN
3 Before use
Caution
•Use the controls only as stated in this user manual.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model number and serial number of your car
audio system.The model number and serial
number are on its bottom.Write the numbers
here:
Model No.: __________________________
Serial No.: ___________________________
Install the car audio system
These instructions are for a typical installation.
However, if your car has different requirements,
make the adjustment accordingly. If you have
any question regarding installation kits, consult
your local retailer.
Caution
•This system is designed for negative ground (earth) 12V
DC operation only.
•Always install this system in the car dashboard. Other
locations can be dangerous as the rear of the system
heats up during use.
•To avoid short-circuit: before you connect, make sure
that the ignition is off.
•Make sure that you connect the yellow and red power
supply leads after all other leads are connected.
•Make sure that all loose leads are insulated with
electrical tape.
•Make sure that the leads do not get caught under
screws iron parts that will move (e.g. seat rail).
•Make sure that all ground (earth) leads are run to a
common ground (earth) point.
•Use only the supplied mounting hardware for a safe
and secure installation.
•Improperfusescancausedamageorre.Whenyou
need to change the fuse, consult a professional.
•When you connect other devices to this system, make
sure that the rating of the car circuit is higher than the
total fuse value of all the connected devices.
•Never connect speaker wires to the metal body or
chassis of the car.
•Never connect speaker wires with stripes to one
another.
Connect wires
Caution
•Make sure that all loose leads are insulated with
electrical tape.
1 Check the car's wiring carefully, and then
connect them to the supplied ISO wires.
a
b
c
d
e
f
g
h

8EN
Connector Connect to
1 Yellow
wire
The +12V car battery which is
live at all times
2 Blue/White
wire
The electric antenna control
lead or power supply lead of
the antenna booster. If there is
no electric antenna or antenna
booster, or it is manually
operated telescopic antenna,
it is unnecessary to connect
this lead.
3 Black wire A metal surface of the car.
Connect the black ground
(earth) lead before connecting
the yellow and red power
supply leads.
4 Red wire The +12V power terminal
which is live in the accessory
(ACC) position of the ignition
switch. If there is no accessory
position, connect to the +12V
car battery terminal that is
always live. Make sure that the
black ground (earth) lead is
connected to a metal surface
ofthecarrst.
5 Green and
green/black
wires
Left speaker (rear)
6 White and
white/black
wires
Left speaker (front)
7 Gray and
gray/black
wires
Right speaker (front)
8 Purple
and
purple/
black
wires
Right speaker (rear)
2 Connect the other end of the supplied
standard connector to the car audio
system.
Connector Connect to
1ANTENNA Antenna for radio
2External Mic An external
microphone for
phone call
3SUBWOOFER
(Socket)
Subwoofer
4REAR LINE OUT L
(Socket)
Rear left speaker
5REAR LINE OUT R
(Socket)
Rear right speaker
6OE REMOTE
(Brown)
OE remote
7FRONT LINE OUT L Front left speaker
8FRONT LINE OUT
R
Front right speaker
Tip
•The pin arrangement for the ISO connectors depends
on the type of vehicle you drive. Be sure to make
proper connections to prevent damage to the system.
a
b
c
d
e
f
g
h
SUB-W
REAR LINE OUT
L
R

9
English
EN
Mount into the dashboard
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
• If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
• If the car battery is not disconnected, to
avoid short-circuit, make sure that the
bare wires do not touch each other.
2 Make sure that the car dashboard opening
is within these measurements:
3 Install the sleeve into the dashboard and
bendthetabsoutwardtoxthesleeve.
Note
•Ifthesystemisnotxedbysleevebutbythesupplied
screws, skip this step.
183 mm
53mm
5mm
4 Place the supplied rubber cushion over the
end of the mounting bolt.
5 Slide the system into the sleeve until you
hear a "click".
183 mm
53.5 mm

10 EN
6 Attach the trim plate.
7 Reconnect the negative terminal of the car
battery.
4 Get started
Turn on
Press .
» [WELCOME] scrolls.
• To turn off the system, press and hold
until [GOODBYE] is displayed.
Change system settings
1 Press and hold to access the system
menu.
2 Press repeatedly to select an option.
• [RDS]
• [PTY >]
• [RDS AF]
• [RDS TA]
• [RDS REG]
• [RDS CT]
• [STORE >]
• [AREA]
• [LOCAL]
• [CLOCK]
• [CLOCK 12H]
• [BEEP]
• [BKO]
• [DIMMER]
• [DEMO]
3 Rotate to select a setting.
• To exit the setting, press .

11
English
EN
Set the clock
1 Press and hold to access the system
menu.
2 Press repeatedly until [CLOCK] and
the current time are displayed.
» If the clock is not set before, [00:00] is
displayed.
3 Rotate to set the hour.
4 Press toconrm.
5 Rotate to set the minute.
6 Press toconrm.
Set the clock format
1 Press and hold to access the system
menu.
2 Press repeatedly until [CLOCK 12H]or
[CLOCK 24H] is displayed.
3 Rotate to select a setting.
• [CLOCK 12H]: 12-hour time format
• [CLOCK 24H]: 24-hour time format
Display the clock
Press to display the clock.
• To exit, press any button.
Select a source
Note
•When all other sources are unavailable, the system
switches the source to [RADIO] automatically.
Press repeatedly to select a source.
• [RADIO]: FM/AM radio
• [MP3-LINK]: the audio input through the
MP3-LINK socket
• [BT AUDIO]: the audio transferred from a
Bluetooth device
• [USB]:When a USB storage device is
connected and recognized, you can select
thissourcetoplayaudiolesthatare
stored on it.
• [iPHONE]:When an iPhone or iPod touch
is connected and recognized, you can
select this source to play the playlist of
iPhone or iPod touch.

12 EN
5 Listen to radio
Select a radio region
You can select a radio region that matches your
location.
1 Press and hold to access the system
menu.
2 Press repeatedly until [AREA] is
displayed.
3 Rotate to select an option.
• [USA] (United States)
• [EUR] (Western Europe)
• [RUS] (Russia)
• [AUS] (Australia)
• [EAS] (Middle East)
• [ASI](AsiaPacic)
• [JAP] (Japan)
• [LAT] (Latin America)
Select a tuner sensitivity
To receive stations with strong signals only or
more radio stations, you can change the tuner
sensitivity.
1 Press and hold to access the system
menu.
2 Press repeatedly until [LOCAL] is
displayed.
3 Rotate to select a setting.
• [LOCAL ON] (local on): Search
stations with strong signals only.
• [LOCAL OFF] (local off): Search
stations with strong and weak signals.
Tune to a radio station
1 Press repeatedly to switch the source
to [RADIO].
2 Press repeatedly to select a band:
[FM1], [FM2], [FM3], [AM1], or [AM2].
3 Press and hold or until the
frequency digits blink.
4 Press or repeatedly to tune to a
radio station manually.
» The radio station is broadcast.
• To search for a radio station
automatically, press or .
Store radio stations in
memory
Note
•You can store a maximum of six stations in each band.
Store stations automatically
1 Press and hold to access the system
menu.
2 Press repeatedly until [STORE >] is
displayed.
3 Press toconrm.
» The strongest stations of the selected
band are saved in preset channels
automatically.
Store stations manually
1 Press repeatedly to select a band.
2 Tune to a radio station that you want to
store.

13
English
EN
3 Press and hold a numeric button for three
seconds.
» The station is saved in the selected
channel.
4 Repeat steps 2 and 3 to store more radio
stations.
• To replace a radio station, store
another one in its channel.
Tune to a preset station
1 Press repeatedly to select a band.
2 Press a numeric key to select a preset
station.
Play with RDS
The RDS (Radio Data System) function
operates only in areas with FM stations
broadcasting RDS signals. If you tune to an RDS
station, the station name is displayed.
Enable the RDS function
Note
•The RDS function is enabled by default.
1 Press and hold to access the system
menu.
2 Press repeatedly until [RDS] is
displayed.
3 Rotate to select [RDS ON].
» The RDS function is enabled.
• To disable the RDS function, rotate
to select [RDS OFF].
Select a program type
Before tuning to RDS stations, you can select
a program type to search for programs of the
selected category only.
1 Press and hold to access the system
menu.
2 Press repeatedly until [PTY >] is
displayed.
3 Press toconrm.
4 Rotate to select a program type, and
then press toconrm.
Item Program
type
Description
1 NEWS News services
2 AFFAIRS Politics and current
affairs
3 INFO Special information
programs
4 SPORT Sports
5 EDUCATE Education and advanced
training
6 DRAMA Radio plays and
literature
7CULTURE Culture, religion and
society
8SCIENCE Science
9VARIED Entertainment programs
10 POP M Pop music
11 ROCK M Rock music
12 EASY M Light music
13 LIGHT M Light classical music
14 CLASSICS Classical music
15 OTHER M Special music programs
16 WEATHER Weather
17 FINANCE Finance
18 CHILDREN Children’s programs
19 SOCIAL Social Affairs
20 RELIGION Religion
21 PHONE IN Phone In
22 TRAVEL Tr avel
23 LEISURE Leisure

14 EN
Item Program
type
Description
24 JAZZ Jazz Music
25 COUNTRY Country Music
26 NATION M National Music
27 OLDIES Oldies Music
28 FOLK M Folk Music
29 DOCUMENT Documentary
30 TEST AlarmTest
31 ALARM Alarm
Use alternate frequencies
If the signal of an RDS station is poor, enable
the AF (Alternate Frequency) function to search
for another station that transmits the same
program.
1 Press and hold to access the system
menu.
2 Press repeatedly until [RDS AF] is
displayed.
3 Rotate to select a setting:
• [AF ON]: Enable the AF function.
• [AF OFF]: Disable the AF function.
Set the region for AF tuning
You can set the region for AF tuning:
[REG
ON]
Only RDS stations in current
region can be tuned to
automatically.
[REG
OFF]
All RDS stations can be tuned to
automatically.
1 Press and hold to access the system
menu.
2 Press repeatedly until [RDS REG] is
displayed.
3 Rotate to select a setting.
Receive trafc announcement
Ifyoudonotwanttomisstrafc
announcement,enabletheTA(Trafc
Announcement) function.
1 Press and hold to access the system
menu.
2 Press repeatedly until [RDS TA] is
displayed.
3 Rotate to select a setting:
• [TA ON]:Whenatrafc
announcement is on air, the system
automatically switches to the tuner
mode and begins to broadcast the
trafcannouncement.Whenthetrafc
announcement is over, the system
returns to the previous mode.
• [TA OFF]:Trafcannouncementdoes
not cut in.
Tip
•Whenatrafcannouncementcutsin,youcanpress
to switch the system to the previous mode.
Synchronize the system clock
You can synchronize the system clock with an
RDS station that transmits time signals.
1 Press and hold to access the system
menu.
2 Press repeatedly until [RDS CT] is
displayed.
3 Rotate to select a setting:
• [CT ON]: Synchronize the system
clock with the RDS station.
• [CT OFF]: Do not synchronize the
system clock.
Tip
•The accuracy of time depends on the RDS station that
transmits the time signal.

15
English
EN
6 Use Bluetooth
devices
With this car audio system, you can listen to
audio from a player or make a call through
Bluetooth.
Pair a device
Note
•Philips does not guarantee compatibility with all
Bluetooth devices.
•Before pairing a device with this system, read its user
manual for compatibility.
On your device, follow the steps below.
1 Enable it to search for other Bluetooth
devices.
2 In the device list, select CMD310.
3 Enter the default password "0000".
» If the pairing is successful, [PAIRED] is
displayed.
• To disconnect the device, disable the
Bluetooth feature on it.
Play audio from a Bluetooth
device
1 Pair the Bluetooth device with this system.
2 Press repeatedly to switch the source
to [BT AUDIO].
» Play starts automatically.
• If play does not start, press .
• To pause play, press again.
• To skip to the previous or next track,
press / .
Tip
•You can also control the play on the Bluetooth device.
Make a call
Note
•Keep the Bluetooth connection active between the
system and your mobile.
Call a number
On your mobile, call a number.
» [CALL---] is displayed.
Redial the last called number
1 Press .
» [REDIAL] is displayed.
2 Press toconrm.
» [CALL---] is displayed.
Pick up an incoming call
When the system receives an incoming call, the
phone number or [PHONE IN] is displayed.
Press to answer the call.
Reject an incoming call
Press and hold until [END] is displayed.
End an call
To end an on-going call, press .
Transfer voice to mobile
Press and hold until [TRANSFER] is
displayed.
» The loudspeakers are muted, and the
voice comes from your mobile only.

16 EN
7 Play from a USB
storage device
Thissystemcanplay.mp3and.wmalesthat
are copied onto a compatible USB storage
device.
Note
•Philips does not guarantee compatibility with all USB
storage devices.
•NTFS(NewTechnologyFileSystem)lesystemisnot
supported.
1 Connect the USB storage device to the
socket.
2 Press repeatedly until [USB] is
displayed.
» Play starts automatically.
If play does not start automatically,
1 Press / to select a folder.
2 Press / toselectale.
3 Press to start play.
RESET
Control play
During play, follow the instructions below to
control play.
Buttons Functions
Pause or resume play.
/ Skip to the previous or next track.
Press and hold to rewind a track or
search forward fast within a track.
/ Skip to the previous or next folder
when one or more folders exist.
Select a repeat mode.
• [REPEAT TRACK]: repeat the cur-
rent track
• [REPEAT ALL]: repeat all tracks
• [REPEAT FOLDER]: repeat all
tracks in the current folder
Enableordisableshufeplay.
• [SHUF FOLDER]: play all tracks in
the current folder randomly
• [SHUF ALL]: play all tracks ran-
domly
• [SHUF OFF]: play tracks in se-
quence

17
English
EN
8 Listen to an
external device
You can use the system to amplify the audio
input that is transferred from an external
device, for example, MP3 player.
1 Press repeatedly to switch the source
to [MP3-LINK].
2 Connect the MP3 link cable to
• the MP3-LINK socket on the system,
and
• the audio output socket (usually the
headphone socket) on the external
device.
3 Play the external device.
9 Use the dock
An application CarStudio is available in the
iTunes App Store for this car audio system.To
enjoy full features, download the application to
your iPhone or iPod touch.
Note
•If the CarStudio application is not installed, a dialog box
prompts you to download it when your iPhone or iPod
touch is docked and recognized.
•If the CarAudio application is installed, a dialog box
prompts you to launch it when your iPhone or iPod
touch is docked and recognized.
Compatible iPod/iPhone
models
This car audio system supports the following
iPod and iPhone models.
• iPhone 4S
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPod touch (3rd and 4th generations)
Prepare for docking
1 Press to eject the dock bracket.

18 EN
2 Pull out the dock bracket until you hear a
"click".
3 Flip the dock bracket upwards.
4 Press and hold RELEASE to loosen the
hooks.
Load your iPhone or iPod
touch
Note
•Before you load your iPhone or iPod touch, make sure
that the dock bracket is in portrait position.
CLICK
1 Connect your iPhone or iPod touch to the
dock with its screen facing you.
» The system switches the source to
[iPHONE] automatically. If not, press
repeatedly to switch the source.
2 Pinch the hooks to secure your iPhone or
iPod touch.
Adjust the dock bracket
Caution
•When the dock bracket is in portrait position, do not
turn it clockwise.
•When the dock bracket is in landscape position, do not
turn it anti-clockwise.
Switch to landscape mode
Note
•Before you turn the dock bracket anti-clockwise, make
sure that you can see the indication line on its left side.
If not, pull the dock bracket outwards.

19
English
EN
1 Turn the dock bracket anti-clockwise by 90
degrees.
2 Adjust the viewing angle.
Switch to portrait mode
1 Turn the dock bracket clockwise by 90
degrees.
2 Adjust the viewing angle.
Pair your iPhone via
Bluetooth
Note
•To use the hands-free function, pair your iPhone with
thecaraudiosystemviaBluetoothrst.
•Make sure that the Bluetooth feature is enabled on
your iPhone.
For an iPhone using iOS 4.X or under
• Manually complete the pairing. (Refer to
"Use Bluetooth devices" > "Pair a device")
For an iPhone using iOS 5.X
• Forthersttime,manuallycomplete
the pairing.Afterwards, the pairing is
automatically complete after your iPhone is
docked and recognized.
Enjoy audio through the dock
If the CarStudio application is not installed on
your iPhone or iPod touch, follow the steps
below.
1 Turn on the car audio system.
2 Press repeatedly to switch the source
to [iPHONE].
3 Playanaudioleorradiostationonyour
iPhone or iPod touch.