Philips CEM220/55 User manual

Register your product and get support at
CEM220
Car Entertainment System
EN User manual 3
CEM220-55-IFU-ENG_1.0.indd 1CEM220-55-IFU-ENG_1.0.indd 1 2008-10-28 10:31:272008-10-28 10:31:27

EN 3
English
Contents
1 Important 4
Safety 4
Notice 4
2 Your Car Audio System 6
Introduction 6
What’s in the box 6
Overview of the main unit 7
Overview of the remote control 8
3 Get started 10
Install the car audio 10
Install remote control battery 15
Turn on 15
Set clock 15
4 Listen to radio 16
Tune to a radio station 16
Store radio stations in memory 16
Tune to a preset station 16
5 Play audio files 17
Play a disc 17
Play from USB/SD/MMC device 17
Control play 18
Search for an MP3/WMA track 18
View play information 18
Intro play 18
Shuffle play 19
Repeat play 19
Connect external sound source 19
6 Adjust sound 20
Adjust volume 20
Mute 20
Turn Dynamic Bass Boost (DBB) on/off 20
Select preset equalizer 20
Other sound settings 20
7 Adjust system settings 21
Select blackout setting 21
Turn demo mode on/off 21
Change button backlight color 21
Select start volume 21
Turn beep sound on/off 22
Turn display scroll on/off 22
Select shock-protect setting 22
Reset 22
8 Additional information 23
Detach the front panel 23
Replace fuse 23
Remove the unit 23
9 Product information 24
10 Troubleshooting 26
11 Glossary 27
CEM220-55-IFU-ENG_1.0.indd 3CEM220-55-IFU-ENG_1.0.indd 3 2008-10-28 10:31:332008-10-28 10:31:33

4EN
English
1 Important
Safety
Read and understand all instructions
before you use your unit. If damage is
caused by failure to follow instructions, the
warranty does not apply.
This unit is designed for negative ground
(earth) 12 V DC operation only.
To ensure safe driving, adjust the volume to
a safe and comfortable level.
Improper fuses can cause damage or
fire.When you need to change the fuse,
consult a professional.
Use only the supplied mounting hardware
for a safe and secure installation.
To avoid short circuit, do not expose the
unit, remote control or remote control
batteries to rain or water.
Never insert objects into the ventilation
slots or other openings on the unit.
Clean the unit and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the unit.
Never place any objects other than discs
into the unit.
Never use solvents such as benzene,
thinner, cleaners available commercially, or
anti-static sprays intended for discs.
Visible and invisible laser radiation when
open. Avoid exposure to beam.
Risk of damage to the unit screen! Never
touch, push, rub or strike the screen with
any object.
•
•
•
•
•
•
•
•
•
•
•
•
Caution
Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
•
Notice
The making of unauthorized copies of copy-
protected material, including computer
programs, files, broadcasts and sound
recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.
This unit includes these labels:
Class II equipment symbol
This symbol indicates that the unit has a double
insulation system.
Recycling
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When you see the crossed-out wheel bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:
CEM220-55-IFU-ENG_1.0.indd 4CEM220-55-IFU-ENG_1.0.indd 4 2008-10-28 10:31:342008-10-28 10:31:34

EN 5
English
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products.The correct
disposal of your old product helps prevent
potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries.The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
This product complies with the radio
interference requirements of the European
Community.
This product complies with the requirements
of the following directives and guidelines:
2004/108/EC + 2006/95/EC.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Any changes or modifications made to this
device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
2008 © Koninklijke Philips Electronics N.V. All
rights reserved.
Specifications are subject to change without
notice.Trademarks are the property of
Koninklijke Philips Electronics N.V. or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
CEM220-55-IFU-ENG_1.0.indd 5CEM220-55-IFU-ENG_1.0.indd 5 2008-10-28 10:31:352008-10-28 10:31:35

6EN
English
2 Your Car Audio
System
Congratulations on your purchase, and
welcome to Philips! To fully benefit from the
support that Philips offers, register your product
at www.Philips.com/welcome.
Introduction
With the in-car audio system, you can enjoy
your drive while you listen to:
FM or AM (MW) radio
Audio from CD or MP3 disc
Audio from a USB drive
Audio from a SD/MMC card
Audio from external devices
What’s in the box
Check and identify the contents of your
package:
a In-car audio system
b Remote control
c Rubber cushion
d Screw (4 pieces)
e Disassembly tool ( 2 pieces)
f Front panel
g Trim plate (2 pieces)
h Carrying case for front panel
iUser manual
jQuick Start Guide
kISO connector
•
•
•
•
•
a
fh
ij
g
dce
b
k
a
fh
ij
g
dce
b
k
CEM220-55-IFU-ENG_1.0.indd 6CEM220-55-IFU-ENG_1.0.indd 6 2008-10-28 10:31:352008-10-28 10:31:35

EN 7
English
Overview of the main unit
a
Select tuner band.
Select MP3/WMA folder.
Scroll up or down menu.
b DBB
Turn on or off Dynamic Bass Boost
(DBB) sound.
c SOURCE
Select audio source.
d /MUTE
Turn the unit on or off.
Adjust volume.
Confirm selection.
•
•
•
•
•
•
•
•
abdghi e cf
s
xwut v
r q po nml kj
abdghi e cf
s
xwut v
r q po nml kj
Enter characters for search.
Mute or unmute the volume.
e MENU / DISP
Display radio frequency, clock and
radio program type (if available).
Display track, elapsed time, artist,
album, title, folder, file and clock.
Access system menu.
f
Return to previous menu.
Stop search.
Disable screen blackout.
g Display panel
•
•
•
•
•
•
•
•
CEM220-55-IFU-ENG_1.0.indd 7CEM220-55-IFU-ENG_1.0.indd 7 2008-10-28 10:31:372008-10-28 10:31:37

8EN
English
h
Unlock the panel
i USB socket
j External equipment socket
k 6
Select preset station no. 6
l 5
Select preset station no. 5
m SHUF, 4
Activate or deactivate shuffle mode.
Select preset station no. 4
n 3, REP
Set repeat play mode.
Select preset station no. 3
o INTRO, 2
Turn intro play on or off.
Select preset station no. 2
p 1,
Start play
Pause or resume play.
Select preset station no. 1
q /
Tune for radio station
Skip/search for a track.
r EQ/Audio
Select equalizer (EQ) setting.
Access audio setting menu.
s SEARCH
Store radio stations automatically.
Search a track or folder.
t Panel power connection
u Disc slot
v
Take disc out.
w RESET
Restore default settings
x SD/MMC card slot
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Overview of the remote
control
a SOURCE
Select audio source.
b VOLUME +/-
Adjust volume.
c EQ
Select EQ setting.
d DBB
Turn on or off Dynamic Bass Boost
(DBB) sound.
e 3, REP
Select repeat play mode.
Select preset station no. 3.
f SEARCH
Store radio stations automatically.
Search a track or folder.
g DISP
Display radio frequency and clock.
•
•
•
•
•
•
•
•
•
j
k
m
n
o
p
q
l
a
b
d
f
g
i
h
c
e
j
k
m
n
o
p
q
l
a
b
d
f
g
i
h
c
e
CEM220-55-IFU-ENG_1.0.indd 8CEM220-55-IFU-ENG_1.0.indd 8 2008-10-28 10:31:392008-10-28 10:31:39

EN 9
English
Display track, elapsed time, artist,
album, title, folder, file and clock.
h 6
Select preset station no. 6.
i 5
Select preset station no. 5.
j SHUF, 4
Activate or deactivate shuffle mode.
Select preset station no. 4.
k 1,
Start play.
Pause or resume play.
Select preset station no. 1.
l INTRO, 2
Turn intro play on or off.
Select preset station no. 2.
m AUDIO
Access audio setting menu.
n Navigation buttons
- /
Tune for radio station
Skip/search for MP3/WMA track.
- /
Select tuner band.
Select MP3/WMA folder.
- SEL
Confirm selection.
o MENU
Access system menu.
p PWR,
Turn the unit on or off.
Mute or unmute volume.
q
Return to previous menu.
Disable screen blackout.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
CEM220-55-IFU-ENG_1.0.indd 9CEM220-55-IFU-ENG_1.0.indd 9 2008-10-28 10:31:402008-10-28 10:31:40

10 EN
English
3 Get started
Caution
Use the controls only as stated in this user manual.•
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for
the model and serial number of your unit.The
model number and serial number are on the
bottom of your unit.Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
Caution
This unit is designed for negative ground (earth) 12 V DC
operation only.
Always install this unit in the car dashboard. Other
locations can be dangerous as the rear of the unit heats
up during use.
To avoid short-circuit: before you connect, ensure that
the ignition is off.
Ensure that you connect the yellow and red power
supply leads after all other leads are connected.
Ensure that all loose leads are insulated with electrical
tape.
Ensure that the leads do not get caught under screws
orin parts that will move (e.g. seat rail).
Ensure that all ground (earth) leads are run to a common
ground (earth) point.
Use only the supplied mounting hardware for a safe and
secure installation.
Improper fuses can cause damage or fire. When you
need to change the fuse, consult a professional.
•
•
•
•
•
•
•
•
•
Note on the power supply lead (yellow)
When you connect other devices to this
unit, ensure that the rating of the car circuit
is higher than the total fuse value of all the
connected devices.
Notes on speaker connection
Never connect speaker wires to the metal
body or chassis of the car.
Never connect speaker wires with stripes
to one another.
Overview of parts
These are the supplied parts needed to
connect and install this unit.
a In-car audio system
b Sleeve
c Front panel
d Trim plate
e Rubber cushion
f Disassembly tools
g Screws 4 pieces
hISO connector
•
•
•
ab
c
efgh
d
ab
c
efgh
d
CEM220-55-IFU-ENG_1.0.indd 10CEM220-55-IFU-ENG_1.0.indd 10 2008-10-28 10:31:412008-10-28 10:31:41

EN 11
English
Connect wires: for cars with ISO
connectors
Caution
Ensure that all loose leads are insulated with electrical
tape.
•
1 Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2 Connect the other end of the supplied
standard connector to the unit.
3 Connect the antenna and amplifier as
illustrated, if applicable.
Connector Connect to
1REAR LINE
OUT R
Rear right
speaker
2REAR LINE
OUT L
Rear left speaker
3SUB OUT Subwoofer
4 ANTENNA Antenna
Connect wires: for cars without ISO
connectors
Caution
Be sure to connect the black ground (earth) lead first.•
1 Connect the antenna and amplifier as
illustrated, if applicable.
A1 A2 A3 A4 A5 A6 A7 A8
B1 B2 B3 B4 B5 B6 B7 B8
A
A
B
abcd
A1 A2 A3 A4 A5 A6 A7 A8
B1 B2 B3 B4 B5 B6 B7 B8
A
A
B
abcd
CEM220-55-IFU-ENG_1.0.indd 11CEM220-55-IFU-ENG_1.0.indd 11 2008-10-28 10:31:442008-10-28 10:31:44

12 EN
English
Connector Connect to
1REAR LINE
OUT R
Rear right
speaker
2REAR LINE
OUT L
Rear left speaker
3 SUB OUT Subwoofer
4 ANTENNA Antenna
2 Cut off the bigger end of the supplied
standard connector.
3 Check the car’s wiring carefully and
connect them to the supplied standard
connector.
A1 A2 A3 A4 A5 A6 A7 A8
B1 B2 B3 B4 B5 B6 B7 B8
A
A
B
abcd
A1 A2 A3 A4 A5 A6 A7 A8
B1 B2 B3 B4 B5 B6 B7 B8
A
A
B
abcd
1Green/black strip Left speaker
(Rear)
2White/black strip Left speaker
(Front)
3 Gray/black strip Right speaker
(Front)
4Purple/black strip Right speaker
(Rear)
B
b
a
c
d
aa
bcd
ab
ef
cd
ghi
b
c
d
B
b
a
c
d
aa
bcd
ab
ef
cd
ghi
b
c
d
CEM220-55-IFU-ENG_1.0.indd 12CEM220-55-IFU-ENG_1.0.indd 12 2008-10-28 10:31:462008-10-28 10:31:46

EN 13
English
eRED Ignition key +12V DC
when ON/ACC
fBLUE Motor/electric antenna
relay control lead/
Amplifier relay control
lead
gBLACK Ground
hOrange/
white
Illumination switch
iYELLOW To the +12V car battery
which is energized at all
times
4 Connect the supplied standard connector
to the unit.
Attach the front panel
1 Insert the right side of the panel in the
chassis until it is correctly engaged.
2 Press the left side of the panel and point
the left hole at the left pillar.
3 Release the panel to engage the left side.
4 Attach the trim plate.
Mount in the dashboard
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
•
•
CEM220-55-IFU-ENG_1.0.indd 13CEM220-55-IFU-ENG_1.0.indd 13 2008-10-28 10:31:472008-10-28 10:31:47

14 EN
English
2 Remove the two screws on the top of the
unit.
3 Remove the mounting sleeve with the
supplied disassembly tools.
4Ensure that car dashboard opening is
within these measurements:.
5Install the sleeve into the dashboard and
bend the tabs outward to fix the sleeve.
Note
Skip this step if the unit is not fixed by sleeve but
supplied screws.
•
183 mm
53mm
5mm
5mm
CEM220-55-IFU-ENG_1.0.indd 14CEM220-55-IFU-ENG_1.0.indd 14 2008-10-28 10:31:482008-10-28 10:31:48

EN 15
English
6Place the supplied rubber cushion over the
end of the mounting bolt.
7Slide the unit into the dashboard until you
hear a click sound.
8Reconnect the negative terminal of the car
battery.
Install remote control battery
Caution
Risk of explosion! Keep batteries away from heat,
sunshine or fire. Never discard batteries in fire.
Risk of decreased battery life! Never mix different brands
or types of batteries.
Risk of product damage! When the remote control is not
used for long periods, remove the batteries.
Perchlorate Material - special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
•
•
•
•
For first-time use:
1 Remove the protective tab to activate the
remote control battery.
To replace the remote control battery:
1 Open the battery compartment.
2 Insert 1 CR2025 batteries with correct
polarity (+/-) as indicated.
Close the battery compartment.
Turn on
1 Press to turn on the unit.
To turn off the unit, press for 3
seconds.
Set clock
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly to until the
currently time is displayed.
3 Tu r n clockwise to set hour.
4Press to confirm.
5 Tu r n anti-clockwise to set minute.
6 Press to confirm.
View clock
1 Press MENU/DISP repeatedly until the
clock is displayed.
•
CEM220-55-IFU-ENG_1.0.indd 15CEM220-55-IFU-ENG_1.0.indd 15 2008-10-28 10:31:492008-10-28 10:31:49

16 EN
English
4 Listen to radio
Tune to a radio station
1 Press SOURCE repeatedly to select Tuner.
2 Press or to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3 Press or to tune to a radio station
manually.
The radio station is broadcast.
To search for a radio station
automatically, press SEARCH for 3
seconds.
Select tuner sensitivity
You can adjust the tuner sensitivity if you want
to receive more radio stations or only stations
with strong signal.
1 Press MENU/DISP for over 2 seconds.
2 Press or repeatedly until [LOCAL] or
[DX] is displayed.
3 Rotate to select a setting:
[LOCAL] (local): Only stations with
strong signal can be broadcast.
[DX] (distance): Stations with strong
and weak signals can be broadcast.
4 Press to confirm the selection.
Select stereo/mono broadcasting
For stations with weak signals: to improve the
reception, change to monoaural sound.
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly until [STEREO]
or [MONO] is displayed.
3 Tu r n to select a setting:
[STEREO]: stereo broadcast.
[MONO]: mono broadcast.
4 Press to confirm the selection.
»
»
•
•
•
•
Store radio stations in
memory
You can store up to 6 stations in each band.
Store staions automatically
1 Press SEARCH for 3 seconds.
The six strongest stations of the
selected band are saved in preset
channels 1-6 automatically.
Store staions manually
1 Tune to a station that you want to store.
(see ‘Tune to a radio station’ on page 16)
2 Press one of the numbered buttons 1to 6
for 3 seconds.
The station is saved in the selected
channel.
Tune to a preset station
1 Press or to select band.
2 Press the number button 1to 6to select
the preset station.
»
»
CEM220-55-IFU-ENG_1.0.indd 16CEM220-55-IFU-ENG_1.0.indd 16 2008-10-28 10:31:512008-10-28 10:31:51

EN 17
English
5 Play audio files
Note
Ensure that the disc or device contains playable files.•
Play a disc
Note
You cannot play CDs encoded with copyright protection
technologies.
•
You can play commercially available audio CDs
and these discs:
CD-Recordables (CD-R)
CD-Re-writables (CD-RW)
MP3 CDs
WMA CDs
1 Press on the front panel to release the
panel.
2 Insert a CD with the printed side facing up.
3 Close the panel.
4 Press 1, to start play.
To pause CD play, press 1 .
To resume CD play, press 1 again.
Remove the CD
To take out the CD,
1 Press .
2 Press beside the disc slot.
•
•
•
•
•
•
Play from USB/SD/MMC
device
Note
Ensure that the USB or SD/MMC device contains
playable music.
•
Insert the USB device
1 Open the cover marked on the
front panel.
2 Insert the USB device into the USB socket.
The unit starts playing from the USB
device automatically.
Remove the USB device
1 Press to turn off the unit.
2 Remove the USB device.
»
CEM220-55-IFU-ENG_1.0.indd 17CEM220-55-IFU-ENG_1.0.indd 17 2008-10-28 10:31:522008-10-28 10:31:52

18 EN
English
Insert SD/MMC card
Note
The system supports SDHC cards.•
1 Press to release the panel.
2 Insert the SD or MMC card into the card
slot.
The unit starts playing from the SD/
MMC card automatically.
Remove the SD/MMC card
1 Press to turn off the unit.
2 Press the card until you hear a click sound.
The card is now disengaged.
3 Remove the SD or MMC card.
Control play
To select a folder, press or .
To skip to the previous/next track, press
or .
To search backward/forward rapidly within
the current track, press or for 3
seconds.
To pause, press 1, .
To resume play, press 1, again.
»
»
•
•
•
•
•
Search for an MP3/WMA
track
1 Press SEARCH for 3 seconds.
Search menu is displayed.
[FILE]: search by track name.
[FOLDER]: search by folder sequence.
2 Tu r n to select [FILE] and then press
to confirm.
3 Tu r n to enter a character and then
press .
4 Repeat steps 3 until the search term is
complete.
5 Press for 3 seconds to start search.
When search is finished, a list of
matching tracks are displayed.
6 Tu r n to skip over the list.
7 Press to select a track.
View play information
1 During play USB/SD/MMC device, press
MENU/DISP repeatedly to view:
Track number and elapsed play time
Artist
Album
Title
Folder
File
Clock
Intro play
You can play the first 10 seconds of each track.
1 During play, press INTRO, 2 to select:
[INT ON] : After the first 10 seconds
of each track have been played, play
stops.
[INT OFF] : Cancel intro play and
start normal play.
»
»
»
»
•
•
•
•
•
•
•
•
•
CEM220-55-IFU-ENG_1.0.indd 18CEM220-55-IFU-ENG_1.0.indd 18 2008-10-28 10:31:542008-10-28 10:31:54

EN 19
English
Shuffle play
You can play the tracks in random order.
1 During play, press SHUF, 4 to select:
[SHUF ON] : start shuffle play for all
tracks.
[SHUF OFF] : cancel shuffle play.
Repeat play
During play, press 3, REP repeatedly to select:
[REP 1] (repeat one track): play the
current track repeatedly.
[REP FOLD] (repeat one folder): play all
tracks in the current folder repeatedly.
[REP ALL] (repeat all tracks): play all tracks
repeatedly.
Connect external sound
source
1 Connect the external sound source to
MP3 LINK socket by using a 3.5 mm cable.
2 Press SOURCE repeatedly until [MP3
LINK] is displayed.
3 Operate the external component (refer to
the instructions supplied with the external
component).
•
•
•
•
•
CEM220-55-IFU-ENG_1.0.indd 19CEM220-55-IFU-ENG_1.0.indd 19 2008-10-28 10:31:562008-10-28 10:31:56

20 EN
English
6 Adjust sound
Adjust volume
1 Tu r n clockwise/anticlockwise to
increase/decrease volume.
Mute
You can turn off the sound of your audio.
1 During play, press MUTE .
To turn the sound back on, press
MUTE again.
Turn Dynamic Bass Boost
(DBB) on/off
1 Press DBB for 3 seconds, the current
setting is displayed:
[DBB ON] :The Dynamic Bass Boost
(DBB) function is on.
[DBB OFF] :The DBB function is off.
2 Press DBB again for 3 seconds to change
the DBB setting.
Select preset equalizer
1 Press EQ/Audio.
The current Equalizer setting is
displayed.
2 Press EQ/Audio again repeatedly to select
a preset EQ:
[USER] (user)
[FLAT] (flat)
[POP] (pop)
[TECHNO] (techno)
[ROCK] (rock)
[CLASSIC] (classic)
[JAZZ] (jazz)
•
»
»
»
•
•
•
•
•
•
•
[OPTIMAL] (optimal)
Other sound settings
You can also edit user preset EQ.
1 Press EQ/Audio for 3 seconds.
2 Press or repeatedly to select the item
to be adjusted:
[BAS] (bass) range: -7 to +7.
[MID] (bass) range: -7 to +7.
[TRE] (treble) range: -7 to +7.
[BAL] (balance) range: 12L to 12R. (L
= left speaker, R = right speaker)
[FAD] (fader) range: 12R to 12F. (R =
rear speaker, F = front speaker)
[LPF] (low pass filter) range: 60, 80,
100, 200.
[MPF] (mid pass filter) range: 500, 1K,
1.5K, 2.5K.
[HPF] (high pass filter) range:10K,
12.5K, 15K, 17.5K.
[SW ON]/[SW OFF] (subwoofer
volume on or off)
[SW VOL] (subwoofer volume) range:
0 to 20.
3 Tu r n to select a value.
4 Press to confirm.
•
•
•
•
•
•
•
•
•
•
•
CEM220-55-IFU-ENG_1.0.indd 20CEM220-55-IFU-ENG_1.0.indd 20 2008-10-28 10:31:572008-10-28 10:31:57

EN 21
English
7 Adjust system
settings
Select blackout setting
You can set the screen to turn off automatically
after the unit is idle for 10 or 20 seconds.
1 Press MENU/DISP for 3 seconds.
2 Tu r n to select a setting:
[BKO 10 S] :Turn off the screen
automatically 10 seconds after last
operation.
[BKO 20 S] :Turn off the screen
automatically 20 seconds after last
operation.
[BKO OFF] : Never turn off the
screen.
3 Press to confirm.
Turn demo mode on/off
When demo mode is on, when the unit is
idle for more than 2 minutes, all functions are
displayed.
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly to until [DEMO]
is displayed.
The screen shows current Demo
mode setting.
3 Tu r n to select a setting:
[DEMO ON] :Turn on the demo
mode.
[DEMO OFF] :Turn off the demo
mode.
4 Press to confirm.
•
•
•
»
•
•
Change button backlight
color
You can change button backlight color from
blue to red or vice versa.
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly to until [KEY
BLUE] or [KEY RED] is displayed.
3 Tu r n to select a setting:
[KEY BLUE]: Backlight turns blue.
[KEY RED]: Backlight turns red.
Select start volume
Each time you turn on the unit, it can play at the
last listened volume or at the preset volume.
1 Press MENU/DISP for 3 seconds.
2 Press or repeatedly to until [V -
LAST] or [V - ADJ] is displayed.
3 Tu r n to select a setting:
[V - LAST] : Each time you turn on
the unit, the volume remains from its
previous use.
[V - ADJ] : Each time you turn on the
unit, the volume is at the preset level.
4 Press to confirm.
Store preset volume
You can turn on the unit at a preset volume.
1 Select [V - ADJ] as the start volume (see
‘Select start volume’ on page 21).
2 Press MENU/DISP for 3 seconds.
3 Press or repeatedly to until [A-VOL]
is displayed.
4 Tu r n to select a value: 0 - 47.
5 Press to confirm.
•
•
•
•
CEM220-55-IFU-ENG_1.0.indd 21CEM220-55-IFU-ENG_1.0.indd 21 2008-10-28 10:31:582008-10-28 10:31:58