Philips CID3683/93 User manual

www.philips.com/welcome
Register your product and get support at CID3683
ENG Quick Start Guide
English
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult your
Philips car audio dealer.
Caution
This unit is designed for negative ground
•
(earth) 12 V DC operation only.
Always install this unit in the car dashboard.
•
Other locations can be dangerous as the
rear of the unit heats up during use.
To avoid short-circuit: before you connect,
•
ensure that the ignition is off.
Ensure that you connect the yellow and red
•
power supply leads after all other leads are
connected.
Ensure that all loose leads are insulated with
•
electrical tape.
Ensure that the leads do not get caught
•
under screws orin parts that will move
(e.g. seat rail).
Ensure that all ground (earth) leads are run
•
to a common ground (earth) point.
Use only the supplied mounting hardware
•
for a safe and secure installation.
Improper fuses can cause damage or fire.
•
When you need to change the fuse, consult
a professional.
Note on the power supply lead (yellow)
When you connect other devices to this•
system, ensure that the rating of the car
circuit is higher than the total fuse value of
all the connected devices.
Notes on speaker connection
Never connect speaker wires to the metal•
body or chassis of the car.
Never connect speaker wires with stripes•
to one another.
Connect wires 1
Caution
Ensure that all loose leads are insulated with
•
electrical tape.
1Check the car’s wiring carefully, then do the
other connections:
Connect GPS antenna 2
To receive signal from satellites, connect the supplied
GPS antenna to your car and the system.
1Connect the supplied GPS antenna to the
system first.
2Stick the other end of the GPS antenna to a
surface for better signal reception.
Mount in the dashboard 3
Note
Check wire connection before you mount
•
the unit into a car.
1Take off the trim plates of the car.
2Open the glove box before the front
passenger seat.
3Connect the wires.
4Replace the screen of the host car audio with
the screen of CID3863.
5Fix the main unit to the mounting brackets
with the M2.6 x 5 screws.
6Fix the mounting brackets to the car with the
M5 x 10 screws.
7Attach the trim plate.
Turn on
Caution
Risk of road accidents! Never watch video
•
or adjust settings while you drive.
1Press and hold to turn on the unit.
The available OSD (On-Screen Display)
»
languages are displayed.
2Touch a language to select.
The OSD language is changed to the
»
selected language immediately.
To turn off the unit, press and hold• .
Set date
1Touch the upper left corner to display main
menu.
2Tou ch in the middle right side of the screen.
The second main menu is displayed.
»
3Touch [Settings].
4Touch [Time].
The date setup menu is displayed.
»
5Touch on the displayed date information.
6Touch or to set year, month and day.
Set clock mode
1Touch [Clock mode].
2Touch on [12Hr] or [24Hr] to select clock
mode.
Tip
When date is set, touch
• first and then
touch to return to main menu.
To set time, refer to the user manual of the
•
host car audio.
Use map
Note
You may need to upgrade the map before
•
using it (see “Upgrade the map” section)
1Touch the upper left corner to display home
menu.
2Touch [Navigation].
The navigation menu is displayed in a few
»
seconds.
3Refer to the map manual (in Chinese) to
operate the navigation tool.
Tip
You can press
• NAVI to enter/exit the
navigation system.
Load discs 4
You can play video, audio or images stored on the
following discs:
DVD video, DVD-R, DVD-RW•
VCD•
Audio CD, CD-R, CD-RW•
1
2
a
b
c
CID3683_93_QSG_V1.0_EN.indd 1CID3683_93_QSG_V1.0_EN.indd 1 2009-9-17 15:17:192009-9-17 15:17:19

Receive call
By default, all incoming calls are received
automatically.
1If there is incoming call, [Incoming call...]
flashes on the screen. Speak into the
Bluetooth microphone.
2When conversation ends, touch (red) to
terminate the call.
Tip
You can select to receive calls manually by
•
set [Auto answer] to [Off] status.
Adjust sound
Adjust volume
To adjust volume, you can:
Press the VOL +/- button on the steering•
wheel.
Rotate the volume knob on the host car•
audio.
Mute
1Touch anywhere except for the upper left
corner to display menu on the screen, if
necessary
2Touch .
The sound is cut off.
»
To resume sound, touch
»again.
Select preset equalizer
You can select preset equalizer:
1Touch anywhere except for the upper left
corner to display menu on the screen, if
necessary.
2 Touch .
The current Equalizer setting is displayed.
»
3Touch or to select an EQ.
4Touch or to adjust below settings:
• [Bass]bass range: -14 to +14.
• [Mid]middle range: -14 to +14.
• [Treb]treble range: -14 to +14.
• [LPH]low pass filter range: 60, 80,
100, 200.
• [MPF]middle pass filter range: 500, 1K,
1.5K, 2.5K.
• [HPF]high pass filter range:10K, 12.5K,
15K, 17.5K .
5Touch to restore the above settings into
default settings.
6 Press to exit.
Note
Ensure that the disc contains playable content.•
1Insert the disc into the disc slot with label
side facing up.
Play starts automatically.
»
To remove the disc, press the
»button.
When the disc is ejected, the unit
»
switches to the previous source, if
connected.
Connect USB device 5
Note
Ensure that the device contains playable
•
content.
1Open the USB door.
2Find the USB cable inside the glove box
before the front passenger seat.
3Remove the lid.
4Insert your USB device to the USB socket.
Play starts automatically.
»
Pair the Bluetooth-enabled
devices
To connect your Bluetooth device to the unit, you
need to pair the device to the unit. Pairing needs
only to be done once.
You can pair up to eight devices.
1Turn on the Bluetooth function on the
device.
2 Search for Bluetooth device with the device.
3Select “CID3683” in the pairing list.
4Enter default password “0000”.
if pairing succeeds. phone call record is
»
displayed.
Make a call
1Pair the phone with the unit.
2 Touch the upper left corner to display the
home menu.
3Touch [Bluetooth].
The Bluetooth menu is displayed.
»
4Touch or to select the paired phone,
then touch .
5Touch or to search for phone number
from the following list:
Or touch to dial number directly, then touch
to dial.
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
CID3683_93_QSG_V1.0
4
5
3
a
c
b
CID3683_93_QSG_V1.0_EN.indd 2CID3683_93_QSG_V1.0_EN.indd 2 2009-9-17 15:17:272009-9-17 15:17:27