Philips CLOCK/TIMER AJ1000 User manual

Register your product and get support at
AJ1000
EN User manual

a
f
c
d
e
b
g
i
j
d
k
l
e
h
100

EN
1 Important
Safety
aRead these instructions.
bKeep these instructions.
cHeed all warnings.
dFollow all instructions.
eDo not use this apparatus near water.
fClean only with dry cloth.
gDo not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
hDo not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers) that
produce heat.
iProtect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
j Only use attachments/accessories specied by the
manufacturer.
kUnplug this apparatus during lightning storms or when unused
for long periods of time.
l Refer all servicing to qualied service personnel. Servicing is
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally, or has been dropped.
mApparatus shall not be exposed to dripping or splashing.
nDo not place any sources of danger on the apparatus
(e.g. liquid lled objects, lighted candles).
oWhere the MAINS plug or an appliance coupler is used as
the disconnect device, the disconnect device shall remain
readily operable.
Warning
Never remove the casing of this apparatus.•
Never lubricate any part of this apparatus.•
Never place this apparatus on other electrical equipment.•
Keep this apparatus away from direct sunlight, naked ames or •
heat.
Never look into the laser beam inside this apparatus.
•
Ensure that you always have easy access to the power cord, plug or•
adaptor to disconnect this apparatus from the power.
Notice
This product complies with the radio interference
requirements of the European Community.
Any changes or modications made to this device that are
not expressly approved by Philips Consumer Lifestyle may void the
user’s authority to operate the equipment.

Recycling
Your product is designed and manufactured with high quality
materials and components, which can be recycled and reused.
When you see the crossed-out wheel bin symbol attached to a
product, it means the product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other household waste. Please
inform yourself about the local rules on the separate collection of
electrical and electronic products.The correct disposal of your old
product helps prevent potentially negative consequences on the
environment and human health.
Environmental information
All unnecessary packaging has been omitted. We have tried to make
the packaging easy to separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags, protective foam
sheet.)
Your system consists of materials which can be recycled and reused
if disassembled by a specialized company. Please observe the local
regulations regarding the disposal of packaging materials, exhausted
batteries and old equipment.

2 Your clock radio
Congratulations on your purchase, and welcome to Philips! To fully
benet from the support that Philips offers, register your product at
www.philips.com/welcome.
Introduction
With this clock radio, you can:
enjoy the FM radio•
know the time•
wake up to buzz or favorite radio tone•
set two alarms to ring at different time.•
What’s in the box
Check and identify the contents of your package:
Main unit (with power adapter attached)•
User manual•
Quick start guide•
Overview of the main unit
aTUNING
Tune to a radio station.•
bREPEAT ALARM/SLEEP OFF
Repeat the alarm.•
Disable the sleep timer.•
cSLEEP
Set the sleep timer.•

d+/-
Adjust the times of clock, alarm timer and sleep timer.•
eAL1,AL2
• RADIO: Set the current radio station as alarm tone.
• BUZ: Set buzz as alarm tone.
• OFF:Turn off the alarm timer.
fVOL
Adjust the volume level of radio.•
gDisplay panel
hAL RESET
Stop the alarm.•
iRADIO ON/OFF
Turn on or off radio.•
jBRIGHTNESS CONTROL
Adjust the brightness of display panel.•
kClock Control
• SET TIME: Activate the clock time setup.
• SET AL1/AL2: Activate the alarm time setup; display the
set alarm time.
• CLOCK: Display the clock time.
lFM ANT
Attached FM radio antenna.•

3 Get started
Caution
Use of controls or adjustments or performance of procedures other•
than herein may result in hazardous radiation exposure or other
unsafe operation.
Always follow the instructions in this chapter in sequence.
If you contact Philips, you will be asked for the model and serial
number of this apparatus.The model number and serial number are
on the bottom of the apparatus.Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Connect power
Caution
Risk of product damage! Ensure that the power supply voltage•
corresponds to the voltage printed on the back or the underside of
the apparatus.
Risk of electric shock! When you unplug the AC power cord, always
•
pull the plug from the socket. Never pull the cord.
Before connecting the AC power cord, ensure you have completed
•
all other connections.
1Connect the power adapter to the power socket.

Set the clock time
1Switch Clock Control to SET TIME.
2Press +/- to set the time (24-hour system).
3Switch Clock Control to CLOCK.
Tip
Press and hold•+to fast increase the time digits.
Press
•-to decrease the time digits one by one.
4 Listen to radio
Tune to a radio station
1Press RADIO ON/OFF to turn on the radio.
2Adjust TUNING slowly to tune to a radio station.
To turn off the radio, press• RADIO ON/OFF again.
Adjust the volume level
1Rotate VOL clockwise or anti-clockwise.

5 Set the alarm timer
Set the alarm time
You can set two separate alarms. For the alarm tone, you can select
the buzz or the FM radio.
Note
Before you start, ensure that the time is set correctly.•
1Switch Clock Control to AL1 or AL2 (on SET AL1/AL2).
2Press +/- to set the alarm time.
3Switch Clock Control to CLOCK.
Turn on the alarm timer
Note
Ensure the alarm time is set successfully.•
1Switch AL1/AL2 to BUZ or RADIO.
»/ appears.
The buzz or FM radio is set for alarm tone.»