Philips SACD 1000/001 User manual

Published by MT 0101 Service PaCE Printed in the Netherlands Subject to modification 53122 785 11020
©
Copyright 2001 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system or transmitted, in any form or by any means, electronic, mechanical,
photocopying, or otherwise without the prior permission of Philips.
DVD-Video Player SACD 1000
/001 /171 /691
CL 06532152_000.eps
151200
Contents Page Contents Page
1 Technical specifications and connection facilities2
2 Warnings, laser safety and service hints 4
3 Directions for use 7
4 Mechanical- and dismantling instructions 20
5 Diagnostic software, trouble shooting and test
instructions 24
6
Wiring and block diagrams
Wiring diagram 59
Block diagram (general) 60
Block diagram (DAC PCB) 61
7
Electrical diagrams and print-layouts Diagram PWB
Display & on/off panel 62 63/64
Switched mode power supply 65 67
LPSU-L2-2N 66 67
AV Board (europe): Video control & SCART
switch (Diagram 1A) 68 71/72
AV Board (europe): Video out (Diagram 1B) 69 71/72
AV Board (europe): Audio (Diagram 2) 70 71/72
AV Board (US & AP): Video (Diagram F1) 73 75/76
AV Board (US & AP): Audio (Diagram F2) 74 75/76
DAC Board: L2N 77 80/81
DAC Board: Audio1-L2N 78 80/81
DAC Board: Audio2-L2N 79 80/81
Mono Board: DVD ALAS (Diagram 1) 82 92-102
Mono Board: Micro controller (Diagram 2) 82 92-102
Mono Board: CD-DVD decoder (Diagram 3) 82 92-102
Mono Board: Program memories (Diagram 4) 82 92-102
Mono Board: CPU & MPEG decoder(Diagram 5)82 92-102
Mono Board: Pwr supply & outp. int.(Diagram 6)82 92-102
Mono Board: SDRAM’s (Diagram 7) 82 92-102
Mono Board: SACD decoder (Diagram 8) 82 92-102
Mono Board: System clocks (Diagram 9) 82 92-102
Mono Board: DAC interface (Diagram 10)82 92-102
8 Alignments (not available) 103
9 Circuit-, IC descriptions and 103
List of abbreviations 152
10 Spareparts list 155

Technical specifications & connection facilities
GB 2 SACD 10001.
1. Technical specifications & connection facilities
1.1 General:
Mains voltage : 120V (98 - 132V
AC) for USA
: 230V (198 -264V
AC) for Europe/Asia
: bymeansofvoltage
selector
Mains frequency : 50 Hz - 60Hz
Power consumption mains : < 36 W
Power consumption standby : < 3 W (remote
operatable)
Power off : < 0.8W
1.2 Audio performance
1.2.1 Line output audio/video
Output voltage 2 channel mode : 2Vrms ±1.5dB
Output voltage 5.1 channel Dolby : 1.41Vrms ±1.5dB
Channel unbalance (1kHz) : <0.85dB
Crosstalk 1kHz : >105dB
Crosstalk 20Hz-20kHz : > 95dB
Frequency response 20Hz- 20kHz : ±0.1dB max
Signal to noise ratio : >100 dB
Dynamic range 1kHz : >90dB
Dynamic range 20Hz-20kHz : >88dB
Distortion and noise 1kHz : >90dB
Distortion and noise20Hz-20kHz : >80dB
Intermodulation distortion : >87dB
Phase non linearity : ±1°max.
Level non linearity : ±0.5dB max.
Mute (spin-up, pause, access) : >100dB
Outband attenuation: : > 50dB above
25kHz
1.2.2 Line output 6 channel
DSD mode stereo +5.1 multi channel (SACD)
Output voltage (1 KHz) : 2Vrms +/- 0.3V
Channel unbalance : <0.5dB
Cut off frequency normal mode (-
3dB) : 40KHz +/- 5KHz
Cut off frequency custom mode (-
3dB) : 50KHz +/- 5KHz
Amplitude linearity (20Hz - 20KHz) : +0.1/-1dB max
normal mode
: +0.1/-0.6 dB max
custom mode
Phase linearity (20Hz - 20KHz) : tbd
SNR dig. silence; normal mode
20KHz : -111 dB (Typical)
: >108dB
SNR dig. silence; normal mode A
weighted : -114 dB (Typical)
: >111dB
SNR 1KHz, -160dB normal mode
500KHz : -50dB (Typical)
: >40dB
SNR 1KHz, -160dB custom mode
500KHz : >40dB (Typical)
: >30dB
THD 0dB 1KHz : 98dB (Typical
custom mode)
: 95 dB (Typical
normal mode)
THD 0dB 20Hz-20KHz : >96dB (custom
mode)
: >90 dB (normal
mode)
Dynamic range -60dB : 114dB (Typical)
: >108 dB
Intermodulation distorsion CCIF : 108dB (Typical)
: >102dB
Low level linearity (-60 to -90 dB) : <0.5dB
Interchannel phase : <1°
Crosstalk (20Hz-20KHz) : 100dB (Typical)
: >90dB
PCM mode up to 6 channels (DVD/ CDDA):
Output voltage (1 KHz) : 2Vrms +/- 0.3V
Channel unbalance : <0.5dB
Amplitude linearity (20Hz - 20KHz) : +0.1/-0.6 dB max
Phase linearity (20Hz - 20KHz) : tbd
SNR dig. silence; normal mode
20KHz : >108dB
SNR dig. silence; normal mode A
weighted : >111dB
THD 0dB (1KHz) : 95 dB typical
THD 0dB (20Hz-20KHz) : >90dB
Dynamic range -60dB : >108dB
Intermodulation distorsion CCIF : 105dB (Typical)
: >100dB
Low level linearity (-60 to -90 dB) : <0.5 dB
Interchannel phase : <1°
Crosstalk (20Hz-20KHz) : 100dB (Typical)
: >90dB
1.3 Video performance
1.3.1 CVBS
CVBS output loaded with 75 Ohm
Fully according PQR3 IMS
1.3.2 S-video (Y/C)
Fully according PQR3 IMS
Connector pinning
1 - GND H
2 - GND H
3 - Y 1Vpp ±0.1V into 75 Ohm
4 - C burst 300mVpp +1/-4dB into 75
Ohm
Aspect ratio switching by DC on C(pin4).
Connector type : 4 pin mini- DIN
1.4 SCART
Fully according PQR3 IMS
Connector implementation according EN50049-1; color =
black; dual SCART
Fully according to prEN1057-2-1
Signal switching is P50 controlled; supported features of
mode 3 see survey of applicable standards.
1.4.1 SCART II (connected to TV)
Pin signals:
1 - Audio R 1.8V RMS k
2 - Audio R j
3 - Audio L 1.8V RMS k
4 - Audio GND H
5 - Blue/Chroma
GND H
6 - Audio L j
7 - Blue out/
Chroma in 0.7Vpp ±0.1V into 75 Ohm (*) l

Technical specifications & connection facilities GB 3SACD 1000 1.
8 - Function
switch <2V = TV
>4.5V / <7V = asp. ratio 16:9 DVD
>9.5V / <12V = asp. ratio 4:3
DVD k
9 - Green GND H
10- P50 control l
11- Green 0.7Vpp ±0.1V into 75 Ohm (*) m
12- Nc
13- Red/Chroma
GND H
14- fast switch
GND H
15- Red out/
Chroma out 0.7Vpp ±0.1V into 75 Ohm (*)
±3dB 0.3Vpp Chroma (burst) m
16- fast switch
RGB/ CVBS or Y <0.4V into 75 Ohm = CVBS
>1V / <3V into 75 Ohm = RGB k
17- Y/CVBS
GND H
18- fast switching
GND H
19- CVBS/Y/RGB
sync 1Vpp ±0.1V into 75 Ohm (*) k
20- CVBS/Y n
21- Shield H
1.4.2 SCART I (connected to AUX)
Pin signals:
1 - Audio R 1.8V RMS k
2 - Audio R j
3 - Audio L 1.8V RMS k
4 - Audio GND H
5 - Blue/Chroma
GND H
6 - Audio L j
7 - Blue in/
Chroma out ±3dB 0.3Vpp Chroma (burst) l
8 - Function
switch j
9 - Green GND H
10- P50 control l
11- Green n
12- Nc
13- Red/Chroma
GND H
14- fast switch
GND H
15- Red in/
Chroma in n
16- fast switch
RGB/ CVBS
or Y j
17- CVBS GND H
18- fast switching
GND H
19- CVBS/Y/RGB
sync 1Vpp ±0.1V into 75 Ohm (*) k
20- CVBS/Y n
21- Shield H
(*) for 100% white
1.5 Digital output
1.5.1 Coaxial
CDDA/ LPCM (incl MPEG1) : according IEC958
MPEG2, AC3 audio : according IEC1937
DTS : accordingIEC1937,
amendment 1
Remark: DTS audio output mode is only available on ‘digital
out’
1.5.2 Optical
identical to coaxial
1.6 P50 SYSTEM CONTROL
Via SCART pin nr 10
1.7 Dimensions and weight
Place and height of feet : acc. to Philips
Harmonisation line
Apparatus tray closed : WxDxH:435x330x
110
Apparatus tray open : WxDxH:435x470x
110
Weight without packaging : ca. 9.5 Kg
Weight in packaging : ca. 13 Kg
1.8 Laser output power & wavelength
1.8.1 SACD/DVD
Output power : 7mW
Wavelength : 650nm
1.8.2 CD
Output power : 10mW
Wavelength : 785nm

Warnings, laser safety and service hints
GB 4 SACD 10002.
2. Warnings, laser safety and service hints
2.1 Warning and laser safety
SHOCK, FIRE HAZARD SERVICE TEST:
CAUTION: After servicing this appliance and prior to returning to customer, measure the resistance between
either primary AC cord connector pins (with unit NOT connected to AC mains and its Power switch ON), and the
face or Front Panel of product and controls and chassis bottom,
Any resistance measurement less than 1 Megohms should cause unit to be repaired or corrected before AC
power is applied, and verified before return to user/customer.
Ref.UL Standard NO.1492.
NOTE ON SAFETY:
Symbol : Fire or electrical shock hazard. Only original parts should be used to replace any part with symbol
Any other component substitution(other than original type), may increase risk or fire or electrical shock hazard.
FATTENTION
Tous les IC et beaucoup d’autres semi-
conducteurs sont sensibles aux décharges
statiques (ESD).
Leur longévité pourrait être considérablement
écourtée par le fait qu’aucune précaution
n’est prise a leur manipulation.
Lors de réparations, s’assurer de bien être
relié au même potentiel que la masse de
l’appareil et enfiler le bracelet serti d’une
résistance de sécurité.
Veiller a ce que les composants ainsi que les
outils que l’on utilise soient également a ce
potentiel.
DWARNUNG
Alle IC und viele andere Halbleiter sind
empfindlich gegen elektrostatische
Entladungen (ESD).
Unsorgfältige Behandlung bei der Reparatur
kann die Lebensdauer drastisch vermindern.
Sorgen sie dafür, das Sie im Reparaturfall
über ein Pulsarmband mit Widerstand mit
dem Massepotential des Gerätes verbunden
sind.
Halten Sie Bauteile und Hilfsmittel ebenfalls
auf diesem Potential.
WAARSCHUWING
Alle IC’s en vele andere halfgeleiders zijn
gevoelig voor elektrostatische ontladingen
(ESD).
Onzorgvuldig behandelen tijdens reparatie
kan de levensduur drastisch doen
verminderen.
Zorg ervoor dat u tijdens reparatie via een
polsband met weerstand verbonden bent met
hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
AVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono
sensibili alle scariche statiche (ESD).
La loro longevita potrebbe essere fortemente
ridatta in caso di non osservazione della piu
grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere
collegato allo stesso potenziale che quello
della massa dell’apparecchio tramite un
braccialetto a resistenza.
Assicurarsi che i componenti e anche gli
utensili con quali si lavora siano anche a
questo potenziale.
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce
life drastically.
When repairing, make sure that you are
connected with the same potential as the
mass of the set via a wrist wrap with
resistance.
Keep components and tools also at this
potential.
WARNING
Safety regulations require that the set be restored to its original condition
and that parts which are identical with those specified be used.
Veiligheidsbepalingen vereisen, dat het apparaat in zijn oorspronkelijke
toestand wordt terug gebracht en dat onderdelen, identiek aan de
gespecifieerde worden toegepast.
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten.
Der Originalzustand des Gerats darf nicht verandert werden.
Fur Reparaturen sind Original-Ersatzteile zu verwenden.
Le norme di sicurezza esigono che l’apparecchio venga rimesso nelle
condizioni originali e che siano utilizzati pezzi di ricambiago idetici a quelli
specificati.
Les normes de sécurité exigent que l’appareil soit remis a l’état d’origine et
que soient utilisées les pièces de rechange identiques à celles spécifiées.
“Pour votre sécurité, ces documents
doivent être utilisés par des
spécialistes agrées, seuls habilités à
réparer votre appareil en panne.”
GB NL
I
D
I
F
GB
NL
CL 96532065_002.eps
120799

Warnings, laser safety and service hints GB 5SACD 1000 2.
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this
device, due to possible eye injury.
LASER DEVICE UNIT
Type: SemiconductorlaserGaAlAs
Wave length: 650 nm (DVD)
780 nm (VCD/CD)
Output Power: 7 mW (DVD)
10 mW (VCD/CD)
Beam divergence: 60 degree
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
AVOID DIRECT EXPOSURE TO BEAM
WARNING
The use of optical instruments with this product will increase eye hazard.
Repair handling should take place as much as possible with a disc loaded inside the player
WARNING LOCATION: INSIDE ON LASER COVERSHIELD
CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅUDSÆTTELSE FOR STRÅLING
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES UNNGÅEKSPONERING FOR STRÅLEN
VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN
VARO! AVATT AESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄKATSO SÄTEESEEN
VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN
DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM
ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU
Warning for powersupply on position 1005
The primary side of the powersupply including the heatsink carries live mains voltage when the
player is connected to the mains even when the player is swiched off !
This primary area is not shielded so it is possible to touch copper tracks and/or components when
servicing the player. Service personnel have to take precautions to prevent touching this area or
components in this area .
The primary side of the powersupply has been indicated with a lightning stroke and a stripe-marked
printed on the printed wiring board
Note:
The screws on the mechanism of theASD1 module (position 81 in on the exploded view drawing)
may never be touched removed or re-adjusted.
Handle the ASD1 module
the ASD1 module
with care when the unit has to be exchanged!
The mechanism of is very sensative for dropping or shocks.
!
CL 06532152_001.eps
051200

Warnings, laser safety and service hints
GB 6 SACD 10002.
2.2 Service hints
2.2.1 Switched Mode Power Supply 1004
This power supply unit is not repairable and must be
exchanged completely in case of failure. A new power supply
can be ordered with codenumber 3104 129 22150.
2.2.2 SACD module
This module can be repaired as follows:
1. The loader and DVD-M(echanism) is one assembly
(VAL6011) item 81. Thisassemblyisanotrepairableunit
and must be exchanged completely in case of failure. A
new unit can be ordered with codenumber 9305 023
61101 (for Europe and Asia Pacific) and 9305 023 61102
(for USA).
2. The mono board has to be repaired down to component
level. Repair handling of the monoboard requires a
workshop with sophisticated desoldering tools.
2.2.3 Service positions
SACD module
See also dismantling instructions.
After demounting the DAC PCB 1005 and the dust bracket
241, it is possible to connect the PC connection and to
demount the SACD module to service the MONO PCB. After
remounting the DAC PCB, the SACD module can be placed
on top of the DAC PCB, protected by an insulation plate.
MONO PCB
Figure 2-1
Figure 2-2
DAC PCB
Figure 2-3
AV PCB
Figure 2-4
Figure 2-5
CL 06532152_002.eps
051200
CL 06532152_003.eps
051200
CL 06532152_004.eps
051200
CL 06532152_005.eps
051200
CL 06532152_006.eps
051200

Directions for use GB 7SACD 1000 3.
3. Directions for use
Rear of player
Caution: Do not touch the inner pins of rear panel connectors. Electrostatic discharge may cause permanent damage to the unit.
English
10 FUNCTION L OVERVIEW
MAINS
VOLTAGE SELECTOR
100-120V220-240V
123
L
R
I
AUX-
I
/O
II
TO TV-
I
/O
SUBW
RIGHT
GND
RIGHT SURR. LEFT SURR. CENTER
LEFT
MULTICHANNEL AUDIO OUT
DIG OUTOPT OUT
DIGITAL AUDIO OUT
Do by Digita /
DTS/MPEG on y
(CVBS) ( Y/C )
VIDEO OUT S-VIDEO
AUDIO
VIDEO OUTSTEREO OUT
FILTER
3104 127 1194.1
VOLTAGE SELECT(or) - For selecting 100/120V or 220/240V. I necessary, adjust the selector to match with your local mains supply
MAINS - Power supply socket or connection to the mains
GND - Ground connector. For making grounding connection between the various components o your system in case o disturbance problems. Also see ‘System grounding’ o chapter ‘Operation - Enhanced use’
Filter switch - See chapter ‘Operation - Enhanced use’
MULTI-CHANNEL AUDIO OUT (For connection to a multi-channel receiver) - SUBW(oo er) - subwoo er connection - CENTER - center speaker connection - RIGHT/LEFT SURR(ound) - surround speaker connections - RIGHT/LEFT - ront speaker connections
VIDEO OUT
- VIDEO OUT (CVBS) - or connection to a TV
with CVBS video inputs
- S-VIDEO OUT (Y/C) - or connection to a
TV with S-Video (Y/C) inputs
TO TV-I/O
- Euroconnector or connection to a TV with Euroconnector
AUX-I/O
- Euroconnector or connection to your VCR
STEREO OUT
- Audio outputs or connection to an ampli ier, receiver
or stereo system
DIGITAL AUDIO OUT
- OPT(ical) OUT digital audio output connector or
connection to digital (optical) equipment
- DIG(ital) OUT digital audio output connector or
connection to digital (coaxial) equipment
Functional overview Front of player
English
FUNCTION L OVERVIEW 9
SACD SVCD
CHAPTER TRACKTITLE
SCANCHAPTERTRACK
TITLE
VIDEO DTS PCM MCH
3
DSUR ALLA-B REPEAT
MCH CD
STEREO
SHUFFLE
TOTAL REM TRACK TIME
F S
T
ON/OFF
SOUND MODE STOP PLAY PAUSE
REPEAT PREV NEXT
OPEN/CLOSE
DIGITAL OUT
TruSurround
with
SRS
DIGITAL VIDEO
SUPER AUDIO CD
SACD 1000
POWER ON/OFF - switches the player on/o
Standby indicator - lights up red when the player is in Standby mode SOUND MODE selects required sound mode: - or SACD: CD, Stereo or Multi-channel (i available) - or DVD/VCD: Stereo, Dolby Surround, 3D Sound or Multi-channel Display - displays the current status o the player
;PAUSE
- interrupts audio/video play or
steps to the next picture rame
REPEAT
SPREV
- selects previous track/title/chapter/index or
beginning o current track/title/chapter/index
TNEXT
- selects next track/title/chapter/index
/OPEN/CLOSE
- opens/closes the disc tray
Disc loading tray
2PLAY
- starts audio/video play
9STOP
- stops audio/video play

Directions for use
GB 8 SACD 10003.
Remote control
English
12 FUNCTION L OVERVIEW
TV
POWER
SACD
POWER
SOUND MODE PLAYSTOP
REVERSE PAUSE SLOW FORWARD
PREVIOUS RESUME NEXT
ZOOM
VOL CH
DISPLAY
ANGLE
TITLE
FTS SHUFFLE SUBTITLE AUDIO
DIM REPEAT REPEAT SCAN
CHAPTER
TC
MUTE
TV POWER - switches the TV to power/standby 9 STOP - stops playback SOUND MODE - selects required sound mode
• or SACD: CD, Stereo or
Multi-channel (i available)
• or DVD/VCD: Stereo, Dolby
Surround, 3D sound or Multi- channel
2 PL Y - starts audio/video play 5REVERSE - search backward ; P USE - pause or still rame/step rame HSLOW - slow motion 6FORW RD - search orward JPREVIOUS - previous track/title/chapter/index e RESUME - resumes playback K NEXT - next track/title/chapter/index VOL +/– - volume up/down in TV mode c MUTE - mutes the sound in TV mode CH +/– - program up/down in TV mode FTS - switches FTS unction ON/OFF - displays FTS menu (FTS = Favourite Track Selection) SHUFFLE - playback in random order
ZSUBTITLE
- subtitle ON/OFF/selects subtitles (DVD/VCD/SVCD only)
YUDIO
- language selection
S CD POWER B - switches the player to power/standby MENU DISC - selects DVD-de ined menu MENU SYSTEM - On-screen Display ON/OFF v w t u - up/down/le t/right cursor movement in OSD mode RETURN - return to previous menu step
aZOOM
- enlarges video image
}NGLE
- selects DVD camera angle DISPL Y - selects elapsed Time display or Remaining Time display OK - acknowledge menu selection 0-9 - numerical key pad T - selects titles C - selects chapters PL YER DISPL Y DIM - adjusts display brightness REPE T - repeats a track or complete disc (CD, VCD, SACD) - repeats a chapter, title or complete disc (DVD) REPE T -B - repeats a particular passage (
A
-
B
)
SC N - playback o the irst 10 seconds o each track, chapter, title
Display
English
FUNCTION L OVERVIEW 11
Super Audio CD inserted Audio CD inserted Super Video CD inserted Video CD inserted
indicate the current active sound mode
DVD video disc inserted
- number o titles on DVD in Stop mode
- number o current title
Number o current chapter
- number o tracks on SACD/CD/VCD in Stop mode
- number o current track
track time in hours, minutes and seconds disc/program time in hours, minutes and
seconds
REM TIME remaining track time in hours, minutes and
seconds when Display mode is set to Remaining time
N
CHAPTER TRACKTITLE
SCAN
X
GHT ALLA B REPEAT
SHUFFLE
TOTAL REM TRACK TIME
N
CHAPTER TRACKTITLE
SCAN
X
GHT ALLA B REPEAT
SHUFFLE
TOTAL REM TRACK TIME
TRACK
M
TITLE
INDECHAPTER
R
ACK
TR
A
M
TITLE
VIDEO
SO
MCH
CD
STEREO
CD
SVCD
SVCD
SACD
SACD
playback temporarily interrupted (not active when setting Personal Pre erences) irst 10 seconds o each track/chapter are played
A passage (
-
B
) is being repeated
tracks/chapters are played in random order
repeat Title/Chapter/Track/All active
FTS (Favourite track selection) program available or CD/DVD/ VCD/SVCD inserted remote control active ( lashing) DTS (Digital Theatre Sound) audio on the digital output Sound mode button ( or DVD) is set to Multi-channel Sound mode button ( or DVD/VCD) is set to Dolby Surround Sound mode button ( or DVD/VCD) is set to 3D Sound
3
DS
SUR
MCH
DTS
F S
T
CHAPTER TRACKTITLE ALL
R
EPEAT
SHUFFLE
T
A-B REPEAT
SCAN
X
F S
T
VGA
DIGITAL
NATURAL
MOTION
SACD SVCD
CD
STEREO
MCH
CHAPTER TRACKTITLE
SCANINDEXCHAPTERTRACK
ALBUM TITLE
HDCDVIDEO AUDIO
PIC
DTS MCH
3
DSUR SPOTLIGHT ALLA-B REPEATGROUP
SHUFFLE
TOTAL REM TRACK TIME

Directions for use GB 9SACD 1000 3.
English
14 PREP R TION
Preparation General notes - Depending on your ampli ier/receiver/Stereo System there are various ways you could connect the player. These are explained in the chapter below. - For some connections settings or digital and/or analog output are required. These settings have to be made in the ‘Personal Pre erences’ menu which is only accessible via your TV screen. In these cases you will need to connect the player to the TV as well. - Please re er to your ampli ier/receiver/Stereo System, TV and any other User Manual(s) as necessary to make the optimal connections. Caution: Do not connect the player’s audio output to the phono input of your audio system. Connecting to audio equipment - analog Connecting to an amplifier/receiver equipped with two channel analog stereo ●Connect the audio Le t and Right outputs or Front
speaker connection (1) to the corresponding sockets on your ampli ier, receiver or stereo system. For this use the audio cable supplied.
Connecting to a Multi-channel udio/(Video) receiver with 6 connectors This SACD player contains a multi-channel decoder. This enables playback o SACDs recorded in Multi-channel. You only need to select Multi-channel using the Sound Mode key. 1Connect the audio Le t and Right outputs or Front
speaker connection (1) to the corresponding input sockets on your receiver. For this use the audio cable supplied.
2Connect the audio Le t and Right outputs or
Surround speaker connection (2) to the corresponding inputs on your receiver. For this use an optional audio cable.
3Connect the audio outputs or Center speaker and
Subwoo er connection (3) to the corresponding
inputs on your receiver. For this use an optional audio cable.
Note: If the subwoofer is equipped with its own amplifier, the Subwoofer connection should be connected to the subwoofer directly.
MAINS
VOLTAGE SELECTOR
100-120V220-240V
123
L
R
I
AUX-
I
/O
II
TO TV-
I
/O
SUBW
RIGHT
GND
RIGHT SURR. LEFT SURR. CENTER
LEFT
MULTICHANNEL AUDIO OUT
DIG OUTOPT OUT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
(CVBS) ( Y/C )
VIDEO OUT S-VIDEO
AUDIO
VIDEO OUTSTEREO OUT
FILTER
AMPLIFIER
3
12
MAINS
VOLTAGE SELECTOR
100-120V220-240V
123
L
R
I
AUX-
I
/O
II
TO TV-
I
/O
SUBW
RIGHT
GND
RIGHT SURR. LEFT SURR. CENTER
LEFT
MULTICHANNEL AUDIO OUT
DIG OUTOPT OUT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
(CVBS) ( Y/C )
VIDEO OUT S-VIDEO
AUDIO
VIDEO OUTSTEREO OUT
FILTER
AMPLIFIER
1
English
ON SCREEN DISPL Y INFORM TION 13
On screen display information Menu bar/Status window VUser pre erence dSound WTrack/Title ePicture by Picture XChapter fSlow motion ZSubtitle language gFast motion }Angle hTime search aZoom YAudio language bColour dSound Mode cVideo FTS Status window icons The status window displays the current status o the player and is displayed together with the irst part o the menu bar, i activated in the Features menu (see Personal Pre erences). General
Disc type Tray status
Default screen The de ault screen is displayed when the player is in STOP mode. It may contain a status window (see ‘Status Window’) and a ‘Temporary Feedback Field’. Giving in ormation concerning prohibited actions, playback modes, available angles, etc.
Temporary Feedback Field icons
Scan Repeat All Repeat Title Repeat Track Repeat Chapter Shu le Shu le Repeat Repeat A to end Repeat A-B Current camera angle/number o available camera angles Child Lock On Child Sa e Resume Action prohibited
off no off
off no off
no disc stop

Directions for use
GB 10 SACD 10003.
English
16 PREP R TION
Connecting to a TV Notes - Depending on your T there are various ways you could connect the player. These are shown in the illustration below. - Please refer to your T , CR, and any other User Manual(s) as necessary to make the optimal connections. - Do not connect your SACD-player via your CR, because the video quality could be distorted by the copy protection system. 1Connect the Euroconnector (TO TV-I/O 6) to the
corresponding connector on the TV using the Euroconnector cable supplied.
If your TV is not equipped with a Euroconnector you can select one of the following alternative connections: S-Video (Y/C) connection 1Connect the S-VIDEO OUT (Y/C) socket (7) to the
corresponding socket on the TV using an optional S-Video cable.
●I you wish to receive the sound via your TV
connect the STEREO OUT Le t and Right output sockets (1) to the corresponding sockets on the TV using the audio cable supplied.
Video CVBS connection 1Connect the VIDEO OUT (CVBS) socket (8) to the
corresponding socket on the TV using the video cable supplied.
2I you wish to receive the sound via your TV
connect the STEREO OUT Le t and Right output sockets (1) to the corresponding sockets on the TV using the audio cable supplied.
6 Channel settings - DVD only Front speaker L (Large) : When the ront speakers can reproduce low
requency signals below 120Hz
S (Small) : When the ront speakers cannot produce
low requency signals below 120Hz
Center Speaker* L (Large) : When the center speaker can reproduce
low requency signals below 120Hz
S (Small) : When the center speaker cannot produce
low requency signals below 120Hz
O : When the center speaker is not connected Surround speakers L (Large) : When the surround speakers can reproduce
low requency signals below 120Hz
S (Small) : When the surround speakers cannot
produce low requency signals below 120Hz
O : When the surround speakers are not
connected
Subwoofer On : When you connect a subwoo er O : When a subwoo er is not connected * You can use your T as center speaker. Please refer to your T User Manual to check if your T can reproduce low frequency signals below 120Hz. If not, set Center Speaker to S(small). When Center Speaker is selected in the ‘Personal Preferences’ menu, the sound from both center speaker and audio L/R as well as the audio from the Euroconnector will contain the center speaker audio.
TV Front speaker
right
Front speaker
le t
Center
speaker
Rear speaker
(le t surround)
Rear speaker
(right surround)
MAINS
VOLTAGE SELECTOR
100-120V220-240V
123
L
R
I
AUX-
I
/O
II
TO TV-
I
/O
SUBW
RIGHT
GND
RIGHT SURR. LEFT SURR. CENTER
LEFT
MULTICHANNEL AUDIO OUT
DIG OUTOPT OUT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
(CVBS) ( Y/C )
VIDEO OUT S-VIDEO
AUDIO
VIDEO OUTSTEREO OUT
FILTER
6781
English
PREP R TION 15
Connecting to an amplifier/receiver equipped with Dolby Pro Logic For an ampli ier/receiver with Dolby Surround, you may connect your SACD player in the same way as described or Dolby Pro Logic. Dolby Pro Logic sound 1Connect the audio Le t and Right outputs or Front
speaker connection (1) to the corresponding inputs on the Dolby Pro Logic Audio/Video ampli ier/receiver, using the audio cable supplied.
2Set Analog Output to Dolby Surround in the
‘Personal Pre erences’ menu.
If your amplifier/receiver is equipped with a Dolby Digital decoder ●Connect the player as described in chapter
‘Connecting to an Audio/(Video) receiver with multi channel decoder’.
If you connect the player to a TV equipped with a Dolby Pro Logic decoder ●Connect the player to the TV as described in
chapter ‘Connecting to a TV’.
Connecting to audio equipment - digital The digital output o the SACD1000 does not provide PCM (Pulse Code Modulation) signals. I your ampli er/receiver can decode only PCM and no multi- channel signals such as Dolby Digital, do not connect your SACD player via the digital input. This could damage your ampli ier and/or speakers.
Connecting to an udio/(Video) receiver with multi-channel decoder (Dolby Digital, MPEG 2 and DTS) Digital Multi-channel sound (not for S CD) For this you need a multi-channel A/V receiver that supports one or more o the DVD audio ormats supported by your SACD player (MPEG 2, Dolby Digital and DTS). For this you can check the receiver manual and the logos on the ront o the receiver. 1Connect the player’s digital audio output (optical 4
or coaxial 5) to the corresponding input on the receiver. For this use the digital audio cable (coaxial) is supplied. Optical is optional.
2Set Digital Output to ALL in the ‘Personal
Pre erences’ menu.
Notes: - If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound. The audio format of the D D disc in play is displayed in the Status Window, when changing the audio format. - 6 Channel Digital Surround Sound via digital connection can only be obtained if your receiver is equipped with a Digital Multi-channel decoder. If your receiver does not contain a decoder, you can make the analog connections as described in chapter ‘Connecting to a Multi-channel Audio/( ideo) receiver with 6 connectors’ to obtain 6 Channel Digital Surround Sound. - SACD Multi-channel sound cannot be obtained via digital connection.
MAINS
VOLTAGE SELECTOR
100-120V220-240V
123
L
R
I
AUX-
I
/O
II
TO TV-
I
/O
SUBW
RIGHT
GND
RIGHT SURR. LEFT SURR. CENTER
LEFT
MULTICHANNEL AUDIO OUT
DIG OUTOPT OUT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
(CVBS) ( Y/C )
VIDEO OUT S-VIDEO
AUDIO
VIDEO OUTSTEREO OUT
FILTER
AMPLIFIER
4 5

Directions for use GB 11SACD 1000 3.
English
18 PREP R TION
Infra red remote control Loading the batteries 1Open the battery compartment cover. 2Insert two 'AA' (LR-6) batteries as indicated inside
the battery compartment.
3Close the cover. Caution: Do not mix old and new batteries. nd never mix different types of batteries (standard, alkaline, etc.) Remote control device code To operate the player via the remote control without response o a second DVD player, you can program both player and remote control to use a second set o remote control codes. The de ault system code is Code 1. Programming the player to respond to Code 2 1Press ON/OFF to switch o the player.
2Press or 3 seconds simultaneously press SOUND
MODE and /OPEN/CLOSE on the player and press ON/OFF to switch the player on again. ➤The player will now be programmed to respond to Code 2. ➤When step 1 and 2 are repeated the system code is set to Code 1 again.
Selecting the remote control code
●Simultaneously press DISPL Y and 1 or 2 on the remote control to select code 1 or 2. ➤The remote control will now
be set to the remote control code o your choice. ➤This action can be repeated whenever necessary.
ZOOM
VOL CH
DISPLAY
ANGLE
MUTE
English
PREP R TION 17
Delay times - DVD only Your SACD player is set to reproduce correctly synchronized Digital Surround Sound in a listening area where the surround speakers are about 150cm nearer to the listening position than the ront speakers, and the center speaker is in line with the ront speakers. To adjust or other listening area arrangements, adapt delay times according to the ollowing: Digital Surround Measure the distances in centimeters rom the ront speaker plane and rom the surround speaker plane to the listening positioning plane. Subtract the surround distance rom the ront distance and divide by 30. The result is the required Surround Channel delay time in milliseconds. I the center speaker is on the ront speaker plane, no center speaker delay is needed. You can adjust the delay time in the “User Pre erence Settings”. See Personal pre erence - Sound - Speaker Settings. I , however, it is nearer the listening position, measure the distance in centimeters between the ront and center speaker planes, and divide by 30. The result is the required Center Channel delay time in milliseconds. Dolby Pro Logic I the delay times or Surround Channel and Center Channel are set or Digital Surround mode, the delay times or Dolby Pro Logic mode will automatically be calculated and set.
Connecting the power supply 1Check i the mains voltage as shown on the type
plate (on the back o the player) corresponds to your local mains voltage. I not, adjust the voltage selector (1) to match with your local mains supply.
2Plug the emale end o the power cable supplied into
the Power connector MAINS (2) on the rear o the player.
3Plug the male end o the cord into an AC outlet. Note: When the player is in the STANDBY or OFF position, it is still consuming some power. If you wish to disconnect your player completely from the mains, withdraw the plug from the AC Outlet. Caution: Only qualified service personnel should remove the cover or attempt to service this device.
MAINS
VOLTAGE SELECTOR
100-120V
220-240V
12
15 ms
0 ms
15 ms
15 ms
20 ms
25 ms
30 ms
30 ms
30 ms
15 ms 15 ms 15 ms 15 ms 10 ms
Pre erred Acceptable Not recommended
5 ms
Di erential arrival time
Pro Logic Surround Delay
25
ms 20
ms
0
0 1,5 3 4,5 6 7,5 9 10,5 12
1,5
3
4,5
6
7,5
9
10,5
12
Distance rom surround speakers (m)
Distance rom ront speakers (m)
0 ms
0 ms
0 ms
0 ms
5 ms
10 ms
15 ms
15 ms
15 ms
0
0
0 ms 0 ms 0 ms 0 ms -5 ms
Pre erred Acceptable Not recommended
-10 ms
1,5 3 4,5 6 7,5 9 10,5 12
1,5
3
4,5
6
7,5
9
10,5
12
Di erential arrival time
Digital Surround Delay
Distance rom surround speakers (m)
Distance rom ront speakers (m)
10
ms 5
ms

Directions for use
GB 12 SACD 10003.
English
20 OPER TION
V
Personal preferences
In this mode you can set your personal pre erences or a number o player eatures. Some settings however must be made.This depends on the type o audio equipment connected. For this see ‘Connecting to audio equipment’. General operation
●Press MENU SYSTEM on
the remote control. ●Select Vin the menu bar and press w(down cursor). ➤The Personal Pre erences menu appears.
●Use the t u v w (le t/right/up/down) keys to
toggle through the menus, sub menus and submenu options. ➤When a menu item is selected, the cursor keys (on the remote control) to operate the item are displayed next to the item.
●Press OK to con irm and return to the main menu.
The following items can be adapted:
p
Picture
TV Shape I you have a wide screen (16:9) TV, select 16:9. I you have a regular (4:3) TV, select 4:3. In this case you can also select between: Letterbox or a ‘wide-screen’ picture with black bars top and bottom, or Pan Scan, or a ull-height picture with the sides trimmed. Provided this is avaiIable on the disc in play. I a disc has Pan Scan, the picture then moves (scans) horizontally to keep the main action on the screen. Black level shift (NTSC only) Adapts the colour dynamics to obtain richer contrasts. Select
ON
or
OFF
.
Video shift Factory setting is such that the video will be centered on your screen. Use this setting to personalize the position o the picture on your TV by scrolling it to the le t or right. Colour settings (only when connected via Euroconnector) You can select one o our prede ined sets o colour settings and one set (Personal) which you can de ine yoursel . Personal colour (only when connected via Euroconnector) Allows you to ine-tune the selected colour settings saturation, brightness and contrast.
TV shape
Black Level shift
Video shift
Colour settings Personal colour
1 Personal
2 Rich
Soft
5 Animation
3 Natural
TV shape Black Level shift Video shift Colour settings Personal colour
OK to exit
LETTERBOX PAN SCAN
VIEWIN ON 16:9 VIEWIN ON 4:3
English
OPER TION 19
Operation General explication bout this manual This manual gives the basic instructions or operating this SACD player. When playing DVD discs the player may not respond to all operating commands. Some DVD discs are produced in a way that requires speci ic operation or allows only limited operation during playback. When this occurs, please re er to the instructions in the disc inlay. When a
appears on the TV screen, the operation is not
permitted by the player or the disc. Remote control operation - Unless otherwise stated, all operations can be carried out with the remote control. Always point the remote control directly at the player, making sure there are no obstructions in the path o the in rared beam. - When there are corresponding keys on the ront panel, they can also be used. Menu bar operation - A number o operations can also be carried out via the menu bar on the screen. The menu bar can be called up by pressing any o the ollowing keys on the remote control: MENU SYSTEM, T, C, Angle, Audio Language, Subtitle Language, Zoom and FTS. - The ollowing unctions can be operated via the menu bar:
- Personal Pre erences; - Track/title selection; - Chapter selection; - Audio language selection; - Subtitle language selection; - Angle selection; - Zoom; - Colour selection; - Video FTS selection; - Sound mode; - Picture by picture; - Slow motion; - Fast motion; - Time search.
- The various items can be selected with the t u (le t/right cursor) keys or by pressing the relevant keys on the remote control. - By pressing MENU SYSTEM the menu bar will
disappear rom the screen. - When selecting an item in the menu bar, the selected item will be highlighted and the cursor keys (on the remote control), to operate this item are displayed below the icon. - < or > indicates that more items are available at the le t/right hand side o the menu bar. Press tu(le t/right cursor) to select these items.
Switching on 1I necessary, switch on the TV and select the video
input or your SACD player.
2Press ON/OFF on the player ront panel or
ST NDBY on the remote control. ➤The player display lights up. ➤I the player is connected to the TV the start up screen appears.

Directions for use GB 13SACD 1000 3.
English
22 OPER TION
Status Window Displays the current status o the player and is displayed together with the menu bar. In STOP mode it is displayed together with the ‘Temporary Feedback’ Field in the de ault screen. See ‘On Screen Display in ormation; Factory setting is ON. Select OFF to suppress display o the Status Window. Low Power Standby I this setting is set to ON, the player will go in low- power standby when the Standby button (remote control) is pressed. While in low-power standby, scart AUX-I/O will no longer be available. All external apparatus connected to it will be ignored. PBC This eature allows you to disable or enable the PBC (Playback Control) menu o VCD discs. See under ‘Special VCD eatures’: Factory settings is ON Display information Display Elapsed time - during playback the elapsed playing time will be displayed. Remaining time – during playback the remaining playing time will be displayed. Display setting can be changed during playback with the DISPL Y
button on the remote control.
Player Display Dim (via remote control) This eature allows you to set the display brightness. By repeatedly pressing the
DIM
button on the remote
control you can select: normal brightness, hal brightness and blank display.
off
1
no off
Access control Status window Low power standby Sound mode Display PBC
Total time
Remaining time
no disc stop
English
OPER TION 21
q
Sound
nalog output Select Stereo, Dolby Surround, 3D Sound or Multi- channel. See ‘Digital and Analog output Settings or DVD/VCD’. Factory setting is Multi-channel. Dolby Surround : Select this setting when using
equipment with a Dolby Surround Pro Logic decoder. In this setting the 5.1 audio channels (Dolby Digital, MPEG- 2) are downmixed to a Dolby Surround compatible 2-channel output.
3D-Sound : In a setup without rear speakers
(analog stereo output), 3D Sound remixes the six channels o digital surround into a two speaker output, while retaining all o the original audio in ormation. The result is the listening sensation o being surrounded by multiple speakers.
Multi-channel : Select this setting when using a multi-
channel audio/(video) receiver with six inputs. In this mode, the player will per orm Dolby Digital 5.1-channel decoding when applicable, and Dolby Pro Logic decoding on DVD-Video and (Super) Video-CD discs with 2-channel soundtracks. No Dolby Pro Logic decoding is done with (Super) Audio CD discs.
Night Mode Optimizes the dynamics o the sound with low volume playback. This setting can only be used with discs that support the Night Mode eature. Speaker settings Allows you to select speaker settings, volume balance and delay time and to test the speaker settings. Speaker settings are only active on the Multi-channel Audio Out Outputs. Speaker settings will not be used during playback in SACD Stereo or Multi-channel Sound Mode.
Karaoke vocal Put this setting to ON only when a multi-channel karaoke DVD is being played. The karaoke channels on the disc will then be mixed to a normal stereo sound.
r
Language
Select the required Menu, Audio and Subtitle language. Menu language - The On Screen Menus will be displayed in the language you choose. You can choose rom 8 di erent languages. Audio language - The sound as well as the DVD disc menu will be in the language you choose provided this is available on the disc in play. I not, speech will revert to the irst spoken language on the disc. You can choose rom 16 di erent languages. Subtitle language - The subtitles will be in the language you choose provided this is available on the disc in play. I not, subtitles will revert to the irst subtitle language on the disc. You can choose rom 16 di erent languages. Audio language and Subtitle language can also be adapted via the Menu bar on the screen. s
Features
Sound Mode (S CD only) Selection o de ault SACD Sound Mode: Stereo or Multi- channel. Sound Mode setting can be changed during playback with the Sound Mode button on the player or the remote control. When selecting Multi-channel make sure your sound mode is set up or Multi-channel reproduction. ccess Control (DVD/VCD/SVCD only) Access Control contains the ollowing eatures: Disc Lock - When Disc Lock is set to ON, a 4-digit PIN code needs to be entered in order to play discs. Parental control - Allows the conditional presentation o DVD discs containing Parental Control in ormation.
off
1
no off
Access control Status window Low power standby Sound mode Display PBC
SACD Stereo SACD Multichannel
Speakers Settings
Front L R
Centre
Surround L
Surround R
Sub woofer
Press OK to Exit

Directions for use
GB 14 SACD 10003.
English
24 OPER TION
-
UDIO
Shuffle ●Press SHUFFLE during play.
➤The order o the tracks is changed.
●To return to normal play, press SHUFFLE again.
Repeat track/disc ●To repeat the currently playing track, press
REPE T. ➤
REPE T TR CK
appears on the display.
●To repeat the entire disc, press REPE T a second
time. ➤
REPE T LL
appears on the display.
●To exit Repeat mode, press REPE T a third time.
Repeat -B To repeat or loop a sequence: ●Press REPE T -B at your chosen starting point.
➤
appears on the player display.
●Press REPE T -B again at your chosen end
point. ➤
-
B
appears on the display, and the repeat
sequence begins.
●To exit the sequence, press REPE T -B again.
Scan Plays the irst 10 seconds o each track on the disc. ●Press SC N.
●To continue play at your chosen track, press SC N
again or press 2PL Y.
FTS (Favourite Track Selection) - udio CD only - The FTS eature allows you to store your avourite tracks or a particular disc in the player memory. - Each FTS program can contain 20 tracks. - Each time an FTS program is played it will be placed on top o the list. When the list is ull and a new program is added, the last program in the list will be removed rom the list. - The selections can be called up and played at any time. - For storing an FTS program On Screen Display operation is required.
Storing an FTS-program 1Load a disc and go to Stop mode. 2Use w (down cursor) to go to the list o available
tracks.
3Use tand u(le t/right cursor) to select tracks rom
the list. To go directly to any track, enter the track number using the numerical keys 0-9.
4Store each track by pressing OK.
➤The track numbers will be added to the list o selected tracks. ➤The number o tracks and the playing time o the program will be shown on the player display and the audio screen.
When your FTS program is complete, press 2PL Y to
start play, the FTS program will be automatically memorized. ●Press FTS or use the tu(le t/right cursor) to set
FTS to ON or OFF.
Erasing a track from an FTS-program 1Use w(down cursor) to go to the list o selected
tracks.
2Use tand u(le t/right cursor) to select the track
number you wish to erase. To go directly to any track, enter the track number using the numerical keys 0-9.
3Press OK.
➤The track number will be erased rom the list o selected tracks.
Erasing the complete program ●Use w(down cursor) to select
Clear All
and press
OK. ➤The complete FTS program or the disc will be erased.
stop stereo track
time
total tracks
Audio Disk Mode
track 1 2 3 5 6 7 8
program
Clear all
fts On Off
CD 8 10321
total time
stop
English
OPER TION
-
UDIO 23
Operation - udio (Super udio CD and CD) Loading a S CD or udio disc 1Press /OPEN/CLOSE on the ront o the player.
The disc loading tray opens.
2Lay the disc in the tray, label side up. Make sure it is
sitting properly in the correct recess.
3Gently push the tray, or press /OPEN/CLOSE,
to close the tray. ➤READING appears on the player display and in the status window (i TV is on).
I a Super Audio CD is inserted the Sound Modes available on the disc will be shown on the player display. The current Sound Mode is indicated on both player display (with a bullet) and screen (i TV is on). Playing a S CD or udio disc ●Press 2PL Y to start playback.
➤During playback o Super Audio CDs and audio discs all unctions can be operated via the buttons on the remote control and the player ront. ➤I the TV is on, the Super Audio CD or the Audio CD screen appears. ➤During play, the current track number and its elapsed playing time will be shown on the player display (and on the screen). I a de ault Display Time setting (Total Time/Remaining Time) is made in the Personal Pre erences menu this will be shown during playback. With the DISPL Y button on the
remote control other time indications can be selected. ➤When playing a Super Audio CD the currently selected Sound mode will be indicated on the display with a bullet. ➤At the beginning o each track the number o ront channels and surround channels will be displayed (e.g. 3/2). I a subwoo er channel is present this will also be displayed (+1).
➤I a de ault Sound mode (Stereo/Multi-channel) is selected in the Personal Pre erences menu and this Sound mode is not availabale on the disc inserted, playback will start in the irst available Sound mode on the disc. ➤Playback will stop at the end o the disc.
●To stop play at any other time, press 9 STOP.
➤The number o tracks and the total playing time will be shown on the player display (and on the screen).
Sound mode - S CD playblack ●Press SOUND MODE on the player or the
remote control to select the required Sound mode: Stereo - Super Audio Stereo reproduction. Multi-channel - Super Audio Multi-channel reproduction. CD - normal CD stereo reproduction (press 9 STOP irst, then press SOUND MODE).
The sound modes available on the disc are indicated on the display. When selecting Multi-channel make sure your speaker con iguration is set up or Multi-channel reproduction. Pause ●Press ;P USE during play.
●To return to play, press 2PL Y.
Search ●To search orwards or backwards through the disc
at 4x normal speed, press 5REVERSE or 6
FORW RD during play. ➤Search begins, and sound is muted.
●To step up to 8x normal speed, press 5REVERSE
or 6FORW RD again. ➤Search goes to 8x speed.
●To return to 4x normal speed, press 5REVERSE
or 6FORW RD again.
●I the TV is on, search speed and direction are
indicated on the screen each time 5REVERSE or 6FORW RD is pressed.
●To end the search, press 2PL Y or 9STOP as
desired. ➤Sound muted in 4x and 8x search.
Moving to another track ●Press KNEXT brie ly during play to step orward
to the next track.
●Press JPREVIOUS brie ly during play to return to
the beginning o the current track. Press J PREVIOUS brie ly again to step back to the previous track.
●To go directly to any track, enter the track number
using the numerical keys 0-9.
SACD
MCH CD
STEREO
STOP PLAY PAUSE
REPEAT PREV NEXT
OPEN/CLOSE

Directions for use GB 15SACD 1000 3.
English
26 OPER TION
-
VIDEO
ccess control; Parental control (DVD-Video only) Movies on DVD discs may contain scenes not suitable or children. There ore discs may contain ‘Parental Control’ in ormation which applies to the complete disc or to certain scenes on the disc. These scenes are rated rom 1 to 8 and alternative, more suitable scenes are available on the disc. Ratings are country dependent. The ‘Parental Control’ eature allows you to prevent discs rom being played by your children or to have certain discs played with alternative scenes. ctivating/Deactivating Parental Control 1In Stop mode, select
Access Control
in the
Features menu susing the w/v(down/up) keys and press u(right cursor).
2Enter your 4-digit PIN code. I necessary enter the
code a second time.
3Move to
Parental Level
using the w/v(down/up)
keys.
4Move to the Value Adjustment bar using the u(right
cursor) key.
5Then use the w/v(down/up) keys or the numerical
keys 0-9 on the remote control to select a rating rom 1 to 8 or the disc inserted.
Rating 0 (displayed as ‘– –’): Parental Control is not activated. The Disc will be played in ull. Ratings 1 (child safe) to 8 (adults only): The disc contains scenes not suitable or children. I you set a rating or the player, all scenes with the same rating or lower will be played. Higher rated scenes will not be played unless an alternative is available on the disc. The alternative must have the same rating or a lower one. I no suitable alternative is ound, play will stop and the 4-digit code has to be entered.
6Press OK or t(le t cursor) to con irm and press t
(le t cursor) again to exit the menu.
Country 1In Stop mode, select
Access Control
in the
Features menu susing the w/v(down/up) keys and press u(right cursor).
2Enter your 4-digit Pincode. 3Move to
Change Country
using the w(down) key.
4Press the u(right) key.
5Select a country using w/v(down/up cursor). 6Press OK or t(le t cursor) to con irm and press t
(le t cursor) again to exit the menu.
Changing the 4-digit code 1In Stop mode, select
Access Control
in the
Features menu susing the w/v(down/up) keys and press u(right cursor).
2Enter the old code. 3Move to
Change Code
using the w(down) key.
4Press the u(right) key.
5Enter the new 4-digit PIN code. 6Enter the code a second time and recon irm with
OK.
7Press t(le t cursor) to exit the menu.
Note: If you forgot your code, press 9STOP four times
while in the access control PIN code box and exit with OK. Access control is now switched off. You can then enter a new code (twice!) as described above.
Access control
Status window
Low power standby Sound mode Display PBC
Child lock Parental level
Change country
Change code
Access control
Status window
Low power standby Sound mode Display PBC
enter code
English
OPER TION
-
VIDEO 25
Operation - Video (DVD and VCD) ccess control; disc lock (DVD and VCD) ctivating/deactivating the disc lock 1In Stop mode, select
Access Control
in the
Features menu susing the w/v(down/up) keys and press u(right cursor).
2Enter a 4-digit PIN code o your own choice. 3Enter the code a second time. 4Move to
Child lock
using the w/v(down/up) keys.
5Move to Ç/ Éusing the u(right cursor) key.
6Select Çusing the w/v(down/up) keys.
7Press OK to con irm or t(le t cursor) to con irm
and press t(le t cursor) again to exit the menu. ➤Now unauthorized discs will not be played unless the 4-digit code is entered.
8Select Éto deactivate the disc lock.
Note: Reconfirmation of the 4-digit PIN code is necessary when: - The code is entered for the very first time (see above); - The code is changed (see ‘Changing the 4-digit code’); - The code is cancelled (see ‘Changing the 4-digit code’); - Both Disc lock and Parental Control are switched OFF and the code is requested.
uthorizing discs ●Insert the disc. See ‘Loading a disc’.
➤The Disc lock dialog will appear. You will be asked to enter your secret code or ‘Play Once’ or ‘Play Always’. I you select ‘Play Once’, the disc can be played as long as it is in the player and the player is in the ON position. I you select ‘Play Always’, the disc will become child sa e (authorized) and can always be played even i the Disc lock is set to ON.
Notes: The player memory maintains a list of up to 80 authorized (‘Child safe’) disc titles. A disc will be placed in the list when ‘Play Always’ is selected in the ‘child protect’ dialog. Each time a ‘child safe’ disc is played it will be placed on top of the list When the list is full and a new disc is added, the last disc in the list will be removed from the list. Double sided D D discs may have a different ID for each side. In order to make the disc ‘child safe’, each side has to be authorized. Multi volume CD disc may have a different ID for each volume. In order to make the complete set ‘child safe’, each volume has to be authorized. Deauthorizing discs ●Insert the disc. See ‘Loading a disc’.
➤Playback starts automatically.
●Press 9STOP while {is visible.
➤The |will appear and the disc is now
deauthorized.
Acces Control
locked
Choose Play always for inserting disc in the child safe list
Play once Play always
Acces control
Status window Low power standby Sound mode Display PBC
Child lock
Change country
Parental level
Change code

Directions for use
GB 16 SACD 10003.
English
28 OPER TION
-
VIDEO
General features Note: Unless stated otherwise, all operations described are based on remote control operation. A number of operations can also be carried out via the menu bar on the screen. (see ‘Menu bar operation’) Moving to another title/track When a disc has more than one title or track (which you can see rom both the menu bar and the player display), you can move to another title as ollows: ●Press T(title), then press K NEXT brie ly during
play to select the next title/track.
●Press T(title), then press J PREVIOUS brie ly
during play to return to the beginning o the current title/track. Press J PREVIOUS twice brie ly to step back to the previous title/track.
●To go directly to any title or track, select T(title),
then enter the title number using the numerical keys 0-9.
Note: If the number has more than one digit, press the keys in rapid succession. Moving to another chapter/index When a title on a disc has more than one chapter or a track has more than one index (which you can see rom the player display and on the menu bar), you can move to another chapter/index as ollows: ●Press K NEXT brie ly during play to select the next
chapter/index.
●Press J PREVIOUS brie ly during play to return to
the beginning o the current chapter/index. Press J PREVIOUS twice brie ly to step back to the previous chapter/index.
●To go directly to any chapter or index, select C
(chapter), then enter the chapter or index number using the numerical keys 0-9.
Note: If the number has more than one digit, press the keys in rapid succession. Slow Motion ●Select f(Slow motion) in the menu bar. ●Use the w(down) key to enter the Slow Motion
menu. ➤The player will now go into Pause mode.
●Use the t u (le t/right) keys to select the required
speed: -1, -1/2, -1/4 or -1/8 (backward); +1/8, +1/4, +1/2 or +1 ( orward).
●Select 1 to play at normal speed again. ●I ;P USE is pressed, the speed will be set to 0.
●To exit slow motion mode, press 2PL Y and then
v(up cursor).
You can also select Slow motion speeds by using the H button on the remote control.
Still Picture and Step Frame ●Select e(picture by picture) in the menu bar.
●Use the w(down) key to enter the picture by
picture menu. ➤The player will now go into Pause mode.
●Use t u (le t/right) keys to select previous or next
picture.
●To exit Picture by picture mode, press 2PL Y.
You can also step orward by using the ;P USE repeatedly on the remote control.
Search ●Select g(Fast motion) in the menu bar. ●Use the w(down) key to enter the Fast motion
menu.
●Use the t u (le t/right) keys to select the required
speed: -32, -8 or -4 (reverse); +4, +8, +32 ( orward).
●Select 1 to play at normal speed again. ●To exit Fast motion mode, press 2PL Y and then
v(up cursor).
To search orward or backward through di irent speeds, you can also use 5or 6.
Repeat DVD-Video Discs - Repeat chapter/title/disc ●To repeat the currently playing chapter, press
REPE T. ➤
REPE T CH PTER
appears on the player display.
●To repeat the currently playing title, press REPE T
a second time. ➤
REPE T TITLE
appears on the display.
●To repeat the entire disc, press REPE T a third
time. ➤
REPE T LL
appears on the display.
●To exit Repeat mode, press REPE T a ourth time. Video CDs - Repeat track/disc ●To repeat the currently playing track, press
REPE T. ➤
REPE T TR CK
appears on the player display.
●To repeat the entire disc, press REPE T a second
time. ➤
REPE T LL
appears on display and screen.
●To exit Repeat mode, press REPE T a third time.
English
OPER TION
-
VIDEO 27
Loading DVD or VCD discs 1Press /OPEN/CLOSE on the ront o the player.
The disc loading tray opens.
2Lay the disc in the tray, label side up (also when a
double sided DVD disc is inserted). Make sure it is sitting properly in the correct recess.
3Gently push the tray, or press /OPEN/CLOSE,
to close the tray. ➤ READING appears in the status window and on the player display and playback starts automatically.
Note: If a D D disc is inserted and ‘Disc Lock’ is set to ON while the disc inserted is not in the ‘child safe’ list (not authorized), the PIN code must be entered and/or the disc has to be authorized. (see ‘Access Control’) Playing a DVD-video disc Playing a title
➤A ter inserting the disc and closing the tray, playback starts automatically and the status window and the player display show the type o disc loaded as well as in ormation about the disc’s contents and playing time. The disc may invite you to select an item rom a menu. I the selections are numbered, press the appropriate numerical key 0-9; i not, use the w/v, t/u(down/up/le t/right) keys to highlight
your selection, and press OK. ➤The currently playing title and chapter number are displayed in the menu bar and the player display. The elapsed playing time is shown in the status window and the player display. ➤At the beginning o each title the number o ront channels and surround channels will be displayed (e.g. 3/2). I a subwoo er channel is present this will also be displayed (+1). ➤I during play the audio ormat (MPEG 2, Dolby Digital, etc.) o a title changes this will be indicated on the display.
●I required, you can use the SOUND MODE key
to select Stereo, Dolby Surround, 3D-Sound or Multi-channel reproduction. Play may stop at the end o the Title, this can result in return to menu.
●To stop play at any time, press 9STOP.
➤The de ault screen will then appear, giving in ormation about the current status o the player.
●You can resume play rom the point at which you
stopped by pressing e RESUME. ➤The resume eature applies, not only to the disc in the player, but also to the last our discs you have played. Simply reload the disc, press 2PL Y and when you see the Resume icon eon the screen, press 2PL Y again.
Note: Since it is usual for D D movies to be released at different times in different regions of the world, all players have region codes and discs can have an optional region code. If you load a disc of a different region code to your player, you will see the region code notice on the screen. The disc will not play, and should be unloaded.
Playing a video CD Playing a disc - A ter inserting the disc and closing the tray, playback starts automatically and the status window and the player display show the type o disc loaded as well as in ormation about the disc’s contents and playing time - The disc may invite you to select an item rom a menu. I the selections are numbered, press the appropriate numerical key 0-9. - The currently playing track number is displayed in the menu bar and the player display. The elapsed playing time is shown in the status window and the player display. ●I required, you can use the SOUND MODE key
to select Stereo, Dolby Surround or 3D-Sound reproduction.
●To stop play at any time, press 9STOP.
➤The de ault screen will then appear.
●You can resume play rom the point at which you
stopped by pressing e RESUME. The resume eature applies, not only to the disc in the player, but also to the last our discs you have played. Simply reload the disc, press 2PL Y and when you see the Resume icon on the screen e, press
2PL Y again.
STOP PLAY PAUSE
REPEAT PREV NEXT
OPEN/CLOSE

Directions for use GB 17SACD 1000 3.
English
30 OPER TION
-
VIDEO
FTS-Video - The FTS-Video unction allows you to store your avourite titles and chapters (DVD) and avourite tracks (VCD) or a particular disc in the player memory. - Each FTS program can contain 20 items (titles, chapters). - Each time an FTS program is played it will be placed on top o the list. When the list is ull and a new program is added, the last program in the list will be removed rom the list. - The selections can be called up and played at any time. Storing a FTS-Video Program ●In Stop mode, select Video FTS cin the menu bar. ●Press w(down cursor) to open the menu.
➤The Video FTS menu appears. Storing titles/tracks ●Press w(down cursor) to select
title
.
●Use tu(le t/right cursors) to select the
required title.
●Press OK i you wish to store the entire title.
➤The title number will be added to the list o selections.
Storing chapters ●Press w(down cursor) on the selected title
number. ➤The title number will be marked and the highlight moves to the irst available chapter number or this title.
●Use tu(le t/right cursors) to select the
required chapter number.
●Press OK to con irm the selection.
➤The title/chapter selection will be added to the list o selections.
●Press OK or MENU SYSTEM to exit the
Video FTS menu.
Erasing a title/track FTS-Video Program ●In Stop mode, select Video FTS cin the menu bar. ●Use w(down cursor) to select
program
.
●Use tu(le t/right cursors) to select the required
selection number.
●Press OK to erase the selection.
●Press v(up cursor) or MENU SYSTEM to exit
the Video FTS menu.
If you wish to erase all selections: ●In Stop mode, select FTS Video cin the menu bar. ●Use w(down cursor) to select
Clear all
.
●Press OK.
➤All selections will now be erased.
●Press v(up cursor) or MENU SYSTEM to exit
the Video FTS menu.
Switch FTS Video On or Off: ●Select FTS Video cin the menu bar and press w
(down cursor). ➤The video FTS menu appears.
●Press tu(le t/right cursors) to select
On
or
Off
.
●Press v(up cursor) or MENU SYSTEM to exit
the Video FTS menu.
You can also switch FTS Video ON or OFF by using the FTS button on the remote control.
Clear all
On Off
Favorite Track Selection
English
OPER TION
-
VIDEO 29
Repeat -B To repeat or loop a sequence in a title: ●Press REPE T -B at your chosen starting point.
➤
appears on the screen.
●Press REPE T -B again at your chosen end
point. ➤
-
B REPE T
appears on the display, and the
repeat sequence begins.
●To exit the sequence, press REPE T -B.
Scan Plays the irst 10 seconds o each chapter on the disc. ●Press SC N.
●To continue play at your chosen chapter press
SC N again or press 2PL Y.
Shuffle DVD-Video discs This shu les the playing order o chapters within a title, i the title has more than one. ●Press SHUFFLE during play.
➤The shu le icon appears on the screen or about 2 seconds.
●To return to normal play, press SHUFFLE again. Video CDs This shu les the playing order o the tracks, i the disc has more than one. ●Press SHUFFLE during play.
➤The Shu le icon appears on the screen or about 2 seconds.
●To return to normal play, press SHUFFLE again. Time search The Time Search unction allows you to start playing at any chosen time stamp. ●Select h(Time Search) in the menu bar.
●Press w(down cursor).
➤The player will now go into Pause mode. ➤A time edit box appears on the screen showing the elapsed playing time o the current disc.
●Use the digit keys 0-9 to enter the required start
time. Enter hours, minutes and seconds rom le t to right in the box. ➤Each time an item has been entered, the next item will be highlighted.
●Press OK to con irm the start time.
➤The time edit box will disappear and play starts rom the selected time position.
Zoom The Zoom unction allows you to enlarge the video image and to pan through the enlarged image. ●Select a(Zoom) in the menu bar.
●Press w v (down/up cursor) to activate the Zoom
unction and select the required zoom actor; 1.33 or 2 or 4. ➤The player will go into Pause mode. ➤The selected zoom actor appears below the Zoom icon ain the menu bar and ‘
Press OK to
pan
’ appears below the menu bar.
➤The picture will change accordingly.
●Press OK to con irm the selection.
➤The panning icons appear on the screen: v w t
uand OK.
●Use the v w t u (up/down/le t/right) keys to pan
all over the screen.
●When OK is pressed only the zoomed picture will
be shown on the screen.
●I you wish to zoom at any moment, press a
(Zoom) and select the required zoom actor as described above.
●To exit Zoom mode, press 2PL Y.
➤Playback will resume.
Press OK to pan

Directions for use
GB 18 SACD 10003.
English
32 OPER TION
Enhanced use Filter switch Not all ampli iers/receivers and speakers can handle the extended requency response o SACD. Your SACD is equipped with a switchable ilter on the rear. The actory setting o this ilter is 40 KHz which is sa e or all systems. I your system can handle the ull requency range o SACD (check the relevant manuals or, when in doubt, contact your dealer) do the ollowing: Set the switch to the required output signal. Position 1 : 40 kHz - output signal on all speakers is set
to 40 kHz.
Position 2 : 50 kHz FRONT/40 kHz OTHERS - output
signal on ront speakers is set to 50 kHz; output signal on all other speakers is set to 40 kHz.
Position 3 : 50 kHz - output signal on all speakers is set
to 50 kHz.
Warning: When you are not sure your system is able to handle audio input signals up to 50 KHz do not change the output signal. You may damage your speakers or amplifier/receiver.
System grounding When your system consists o a lot o components, occasional disturbance problems (like howling noises) may occur. These problems can be solved by grounding the system. 1Unscrew ground connector GND hal way, connect
an earth wire to the connector and tighten the connector again.
2Connect the earth wire to the ground connector o
the next component in the system.
3I ground connectors are available on the other
components o your system, ground the other components in the same way.
FILTER
MAINS
VOLTAGE SELECTOR
100-120V
220-240V
GND
123
FILTER
MAINS
VOLTAGE SELECTOR
100-120V220-240V
123
RIGHT
GND
LEFT
DIG OUTOPT OUT
DIGITAL AUDIO OUT
Do by Digita /
DTS/MPEG on y
FILTER
English
OPER TION
-
VIDEO 31
Special DVD-features Checking the contents of DVD-Video discs: Menus For titles and chapters, selection menus may be included on the disc. The DVD’s menu eature allows you to make selections rom these menus. Press the appropriate numerical key; or use the w, v, u, t
(down/up/right/le t) keys to highlight your selection, and press OK.
Title menus ●Press DISC MENU.
➤I the current title has a menu, this now appears on the screen. I no menu is present in the title, the disc menu will be displayed.
●The menu can list camera angles, spoken language
and subtitle options, and chapters or the title.
●To remove the title menu, press DISC MENU
again.
Menu Disc ●Press Tollowed by DISC MENU.
➤The disc menu is displayed.
●To remove the disc menu, press DISC MENU
again.
Camera ngle
I the disc contains sequences recorded rom di erent camera angles, the angle icon }appears, showing the number o
available angles, and the angle being shown.
You can then change the camera angle i you wish. ●Use the wv(down/up) keys to select the required
angle in the angle icon.
●To go to any angle directly, enter the angle number
using the numerical keys 0-9. ➤A ter a small delay, play changes to the selected angle. The angle icon remains displayed until multiple angles are no longer available.
Changing the audio language
●Select Y(Audio) in the menu bar.
●Press Yor wv(down/up cursors)
repeatedly to step through the di erent languages.
●You can enter the required language number directly
using the numerical keys 0-9.
Subtitles
●Select Z(Subtitle) in the menu bar. ●Press Zor wv(down/up cursors)
repeatedly to step through the di erent subtitles.
●You can enter the required subtitle number directly
using the numerical keys 0-9.
Special VCD-Features Playback Control (PBC) ●Load a Super Video CD with PBC and press
2PL Y. ➤The PBC menu appears on the TV screen.
●Go through the menu with the keys indicated on the
TV screen until your chosen passage starts to play. I a PBC menu consists o a list o tracks, you can select a track directly.
●Enter your choice with the numerical keys 0-9. ●Press RETURN to go back to the previous menu.

Directions for use GB 19SACD 1000 3.
English
34 BEFORE REQUESTING SERVICE
Player does not respond to all operating Commands during playback Operations are not permitted by the disc. Re er to the instructions in
the disc inlay.
Disturbance problems (like howling noises) during playback Ground the system. See ‘System grounding’.
Cleaning discs Some problems occur because the disc inside the player is dirty. To avoid these problems clean your discs regularly, in the ollowing way: ●When a disc becomes dirty, clean it with a cleaning cloth. Wipe the
disc rom the centre out.
Caution: Do not use solvents such as benzine, thinner, commercially available cleaners, or anti-static spray intended for analog discs. Diagnostic program I the player is still aulty you can start the Diagnostic Program in the player. You can operate the Diagnosis Program by ollowing the step-by-step instructions below. Instructions 1Switch the player OFF with the ON/OFF button.
2Press the OPEN/CLOSE and ;button simultaneously and keep
them pressed while you turn the player ON. ➤On the display the message
BUSY
appears together with a
counter that counts down as the test is running, reaching zero by the end o the test. ➤A ter a ew minutes, the message on the local display changes rom
BUSY
to
ERROR
or to
P SS
.
➤I the message
ERROR
appears on the display, there is apparently
a ailure in your player and your player should be repaired.
3Consult your dealer or the Philips Customer Care Centre or the
nearest Service Repair Shop in your country. The phone number is given in your warranty booklet.
4I the message
P SS
appears on the display, there is apparently no
ailure in your player. In this case the ailure can be caused by incorrect interpretation o the operating instructions, the use o a wrong disc or the act that your player is incorrectly connected. In this case, you should consult your dealer or the Philips Customer Care Centre or urther assistance in solving the problem.
5I the problem remains, return to point 3 o this instruction to ind
the nearest repair shop.
6Switch the player OFF with the ON/OFF button to leave the
diagnostic program.
English
BEFORE REQUESTING SERVICE 33
Before requesting service
I it appears that the SACD player is aulty, irst consult this checklist. It may be that something has been overlooked. Under no circumstances attempt to repair the system yoursel ; this will invalidate the warranty. Look or the speci ic symptom(s). Then per orm only the actions listed to remedy the speci ic symptom(s).
Symptom Remedy No power Check i both plugs o the mains cord are properly connected.
Check i there is power at the AC outlet by plugging in another appliance.
No sound Check audio connections.
I using a HiFi ampli ier, try another sound source.
Distorted sound from HiFi amplifier Check to make sure that no audio connections are made to ampli ier
phono input.
Disc can’t be played Ensure the disc label is upwards.
Clean the disc. Check i the disc is de ective by trying another disc.
No picture Check i the TV is switched on.
Check the video connection.
Distorted picture Check the disc or ingerprints and clean with a so t cloth, wiping rom
centre to edge. Sometimes a small amount o picture distortion may appear. This is not a mal unction.
Completely distorted picture with player menu The NTSC/PAL switch may be in the wrong status. Press the 9STOP
and 6FORW RD buttons simultaneously and keep them pressed while you turn the player ON.
No colour in picture with player menu The NTSC/PAL switch may be in the wrong status. Press the 9STOP
and 6FORW RD buttons simultaneously and keep them pressed while you turn the player ON.
No return to start-up screen when disc is removed Reset by switching the player OFF, then ON again.
Check to see i the program requires another disc to be loaded.
The player does not respond to the remote control Aim the remote control directly at the sensor on the ront o the
player. Avoid all obstacles that may inter ere with the signal path. Inspect or replace the batteries. Check device code setting. See chapter ‘Remote control device code’.
Distorted or black and white picture with DVD or Video CD disc Use only discs that match the TV system o the TV-set used
(PAL/NTSC).
No audio at digital output Check the digital connections.
Check the settings menu to make sure that the digital output is set to on. Check i the audio ormat o the selected audio language matches your receiver capabilities.
Buttons do not work Reset by switching the player OFF then ON again. udible ‘clicks’ from player’s internal During operation the relais o the player may be switched, leading to an
audible ‘click’. This is not a mal unction.

Mechanical- and dismantling instructions
GB 20 SACD 10004.
4. Mechanical- and dismantling instructions
DISMANTLING INSTRUCTIONS See exploded view for item numbers
Front assy(1+2+4+6+7+1001) ⇒ ⇒
remove 4 screws 75
→
78
(front assy
→
frame 181)
⇒
unlock the front from the frame by releasing successively 6 snaps (1 on the left, 2 in the middle, 1 on the right and 2 on the bottom plate)
⇒
Turn the front assy backwards and put it on top of the set (Service position)
mounting
↑ ↓
demounting
Co er 151 ⇒
Remove 9 screws
171
→
174 at both sides
175
→
179 at the rearside
⇒
Lift the cover at the
A/V board 1003 ⇒ ⇒ ⇒
demount the board remove screws (cinches backplate remove the flex connections to the mono board
DAC PCB 1005 ⇒
remove 4 screws 206
→
→
→
209
276
on top of the PCB
⇒
remove 7 screws 269 (cinches
⇒ ⇒
demount the board
Dust Bracket 241
→
→
→
→
→
→
→
→
⇒
demount the bracket
⇒
remove 4 screws 243 246
SACD Mono board 1001 ⇒ ⇒ ⇒ ⇒
SACD MODULE (81 + 1002) ⇒
Remove the connections to the monoboard
⇒ ⇒
Remove 4 screws (255 (dust cover 247 loader 81)
⇒ ⇒ ⇒
Open the tray. If electrically not possible, see the instruction below.
Loader VAL6011/01 81 ⇒
Switched mode power supply 1004
Linear power supply 1005 ⇒
Remove the connections
⇒
Remove the connections
⇒
Demount the board
⇒ ⇒
Remove 4 screws 237 bottom plate)
⇒
Remove 5 screws (board
⇒ ⇒
Transformer 1007
→
→
→
→
→→
→
Display board 1001
⇒ ⇒
Remove 5 screws 30
→
→
demount the board
ON/OFF BOARD 1001
→
front)
⇒
demount the board
⇒
remove screw 30 (board
remove the connections to the DAC PCB
backplate)
open the tray and remove
tray front 45
Remove 4 screws 200 203 (loader 81
85
frame 181)
Demount the module
Is a non repairable unit
Remove 4 screws 82
Remove the flex connections to the turntabel motor and the sledge motor. Remove carefully the flex connection to the OPU and the wire connection to tray motor. Demount the board
(mono board 1002 loader 81)
Remove 2 screws 214 and 215 (board
Remove 2 screws 290 and 291 (mains inled
⇒Demount the board ⇒Release the snaps of 2 spacers
225 and 226 (board
⇒Remove 2 screws 2 and
2 8 (voltage selector
frame)
backplate)
backplate)
frame)
240 (trafo
Demount the transformer
bottom plate)
34
(board front)
rearside to remove
the
Remove dust cover 247
258)
Manually opening of tray When it is not possible to open the tray with the open/close button, the tray can manually be opened. When no disc is loaded, unlock the tray by moving the slide from the left to the right and pull tray outwards.
Remove 4 screws to remove loader.
CL 06532152_049.eps
051200