Philips HTS3520/12 User manual

TABLE OF CONTENTS
Page
Version 1.2
Service Manual
. Mechanical and Dismantling Instructions…………........................3-1
. Software Upgrades and Region Code Change..............................4-1
. Trouble Shooting Chart……………………………………………….5-1
. Wiring Diagram………………………………………..………..….….6-1
. Electrical Diagrams and Print-layouts..….…………………....….…7-1
. Set Mechanical Exploded view & Part list.…………………..….….8-1
©Copyright 2010 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
CLASS 1
LASER PRODUCT
PHILIPS
GB
Published by RY - 039 BU AVM Printed in The Netherlands Subject to modification
HTS3520/12/05/55/51/X78/94/98
. DFU Instruction..............................................................................2-1
. Revision List..................................................................................9-1
Home Theater DVD Player
3139 785 35222
. Technical Specifications…………....………………………..............1-3
. Safety Instruction, Warning & Notes….……………………....….....1-4
. Location of PCB BdsÿVersion Variation and Repair Scenario Matrix..........1-2

LOCATION OF PCB BOARDS：
Version Variation：
HTS3520
Type/Versions
Features /05 /12 /51 /55 /x78 /94 /98
Output Power-600W X X X X X
Output Power-480W X X
Voltage(220~240v) X X
Voltage(110~240v) X X X X
Voltage(220~230v) X
Repair Scenario Matrix：
HTS3520
Type/Versions
Board in used /05 /12 /51 /55 /x78 /94 /98
Main Board C C C C C C C
Front Control Board C C C C C C C
Amplifier Board C C C C C C C
Power Board C C C C C C C
*Bd:Board Level Replacement
*C:Component Level Repair
1-2
MAIN PCB
LOADER
AM PCB
POWER PCB
FRONT
CONTROL PCB

Video
Signal system: PAL / NTSC•
HDMI output: 480i/576i, 480p/576p, 720p,•
1080i, 1080p
Audio
Sampling frequency:•
MP3: 32 kHz, 44.1 kHz, 48 kHz
•
WMA: 44.1 kHz, 48 kHz
•
Constant bit rate:•
MP3: 112 kbps - 320 kbps
•
WMA: 48 kbps - 192 kbps
•
Radio
Tuning range: FM 87.5-108 MHz (50 kHz)•
Signal-to-noise ratio: FM 50 dB•
Frequency response: FM 180 Hz-10 kHz /•
±6dB
USB
Compatibility: Hi-Speed USB (2.0)•
Class support: UMS (USB Mass Storage•
Class)
File system: FAT12, FAT16, FAT32•
Maximum memory support: < 160GB.•
Main Unit
Power supply: 220-240V; ~50 Hz•
Power consumption: 100 W•
Standby power consumption: < 0.9 W•
Dimensions (WxHxD): 360 x 58 x 320•
(mm)
Weight: 2.84 kg•
Subwoofer
Impedance: 8 ohm•
Speaker drivers: 165 mm (6.5”) woofer•
Frequency response: 40 Hz-150 kHz•
Dimensions (WxHxD): 120 x 307 x 369•
(mm)
Weight: 3.84 kg•
Cable length: 4.3 m•
Speakers
System: full range satellite•
Speaker impedance: 8 ohm (center), 4 ohm•
(Front/Rear)
Speaker drivers: 3” full range•
Frequency response: 150 Hz-20 kHz•
Dimensions (WxHxD):•
HTS3510: 96 x 162 x 96 (mm)
•
HTS3520:
•
Center: 160.9 x 95 x 92 (mm)
Front/Rear: 95 x 160.9 x 87 (mm)
Product specifications
Note
Specification and design are subject to change
•
without notice.
Region code
Playback media
DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R
DL, CD-R/CD-RW, Audio CD,Video CD/SVCD,
Picture CD, MP3-CD,WMA-CD, USB storage
device
File Format
Audio: .mp3, .wma•
Video: .mpeg, .mpg,•
Picture: .jpeg, .jpg•
Amplifier
Total output power:•
HTS3510: 300 W RMS
•
HTS3520: 600 W RMS
•
Frequency response: 20 Hz-20 kHz / ±3dB•
Signal-to-noise ratio: > 65 dB (CCIR) /•
(A-weighted)
Input sensitivity:•
AUX: 1 mV
•
Country DVD
Europe, United Kingdom
Latin America
Australia, New Zealand
Russia, India
China
Asia Pacific, Taiwan, Korea
Weight:•
HTS3510: 0.68 kg
•
HTS3520:
•
Center: 0.77 kg
Front/Rear: 0.56 kg/each
Cable length:•
Center: 3 m
•
Front: 4 m
•
Rear: 10 m
•
Laser specification
Type: Semiconductor laser GaAIAs (CD)•
Wave length: 645 - 665 nm (DVD), 770 -•
800 nm (CD)
Output power: 6 mW (DVD), 7 mW•
(VCD/CD)
Beam divergence: 60 degrees.•
HTS3520/12/05:
1-3

Product specifications
Note
Specification and design are subject to change
•
without notice.
Region code
Playback media
DVD-Video, DVD+R/+RW, DVD-R/-RW, DVD+R
DL, CD-R/CD-RW, Audio CD,Video CD/SVCD,
Picture CD, MP3-CD,WMA-CD, USB storage
device
File Format
Audio: .mp3, .wma•
Video: .mpeg, .mpg,•
Picture: .jpeg, .jpg•
Amplifier
Total output power:•
HTS3510: 240 W RMS (10% THD)
•
HTS3520: 480 W RMS (10% THD)
•
Frequency response: 20 Hz-20 kHz / ±3dB•
Signal-to-noise ratio: > 65 dB (CCIR) /•
(A-weighted)
Input sensitivity:•
AUX: 1 mV
•
Country DVD
Europe, United Kingdom
Latin America
Australia, New Zealand
Russia, India
China
Asia Pacific, Taiwan, Korea
Video
Signal system: PAL / NTSC•
HDMI output: 480i/576i, 480p/576p, 720p,•
1080i, 1080p
Audio
Sampling frequency:•
MP3: 32 kHz, 44.1 kHz, 48 kHz
•
WMA: 44.1 kHz, 48 kHz
•
Constant bit rate:•
MP3: 112 kbps - 320 kbps
•
WMA: 48 kbps - 192 kbps•
Dimensions (WxHxD):•
HTS3510: 96 x 162 x 96 (mm)
•
HTS3520:•
Center: 160.9 x 95 x 92 (mm)
Front/Rear: 95 x 160.9 x 87 (mm)
Weight:•
HTS3510: 0.68 kg
•
HTS3520:
•
Center: 0.77 kg
Front/Rear: 0.56 kg/each
Cable length:•
Center: 3 m
•
Front: 4 m
•
Rear: 10 m
•
Laser specification
Type: Semiconductor laser GaAIAs (CD)•
Wave length: 645 - 665 nm (DVD), 770 -•
800 nm (CD)
Output power: 6 mW (DVD), 7 mW•
(VCD/CD)
Beam divergence: 60 degrees.•
Radio
Tuning range: FM 87.5-108 MHz (50/100•
kHz)
Signal-to-noise ratio: FM 50 dB•
Frequency response: FM 180 Hz ~ 10 kHz•
/ ±6dB
USB
Compatibility: Hi-Speed USB (2.0)•
Class support: UMS (USB Mass Storage•
Class)
File system: FAT12, FAT16, FAT32•
Maximum memory support: < 160GB.•
Main Unit
Power supply:•
Asia Pacific/Latin America/India: 110-
•
240V, ~50-60Hz
China: 220-230V, ~50-60Hz
•
Russia: 230V, ~50Hz
•
Power consumption: 100 W•
Standby power consumption: < 0.9 W•
Dimensions (WxHxD): 360 x 58 x 320•
(mm)
Weight: 2.84 kg•
Subwoofer
Impedance: 8 ohm•
Speaker drivers: 165 mm (6.5”) woofer•
Frequency response: 40 Hz-150 kHz•
Dimensions (WxHxD): 120 x 307 x 369•
(mm)
Weight: 3.84 kg•
Cable length: 4.3 m•
Speakers
System: full range satellite•
Speaker impedance: 8 ohm (center), 4 ohm•
(Front/Rear)
Speaker drivers: 3” full range•
Frequency response: 150 Hz-20 kHz•
HTS3520/55/X78:
1-4

HTS3520/51: 1-5

1-6

HTS3520/94:
1-7

Speakers
System: full range satellite•
Speaker impedance: 8 ohm (center), 4 ohm•
(Front/Rear)
Speaker drivers: 3” full range•
Frequency response: 150 Hz-20 kHz•
Dimensions (WxHxD):•
HTS3510: 96 x 162 x 96 (mm)
•
HTS3520:
•
Center: 160.9 x 95 x 92 (mm)
Front/Rear: 95 x 160.9 x 87 (mm)
Weight:•
HTS3510: 0.68 kg
•
HTS3520:
•
Center: 0.77 kg
Front/Rear: 0.56 kg/each
Cable length:•
Center: 3 m
•
Front: 4 m
•
Rear: 10 m
•
Laser specification
Type: Semiconductor laser GaAIAs (CD)•
Wave length: 645 - 665 nm (DVD), 770 -•
800 nm (CD)
Output power: 6 mW (DVD), 7 mW•
(VCD/CD)
Beam divergence: 60 degrees.•
1-8

Product Specification
HTS3520/98:
1-9

1-10

Safety instruction
1. General safety
Safety regulations require that during a repair:
. Connect the unit to the mains via an isolation transformer.
. Replace safety components indicated by the symbol ,
only by components identical to the original ones. Any
other component substitution (other than original type)
may increase risk of fire or electrical shock hazard.
Safety regulations require that after a repair, you must
return the unit in its original condition. Pay, in particular,
attention to the following points:
. Route the wires/cables correctly, and fix them with the
mounted cable clamps.
. Check the insulation of the mains lead for external
damage.
. Check the electrical DC resistance between the mains
plug and the secondary side:
1) Unplug the mains cord, and connect a wire between
the two pins of the mains plug.
2) Set the mains switch the “on” position (keep the
mains cord unplug).
3) Measure the resistance value between the mains
plug and the front panel, controls, and chassis
bottom.
4) Repair or correct unit when the resistance
measurement is less than 1M
¡
.
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit “off”, and remove the wire between
the two pins of the mains plug.
2.Laser safety
This unit employs a laser. Only qualified service personnel
may remove the cover, or attempt to service this device
(due to possible eye injury).
Laser device unit
Type :SemiconductorlaserGaAlAs
Wavelength : 650nm (DVD)
: 780nm (VCD/CD)
Output power : 7mW (DVD)
:10mW(DVD/CD)
Beam divergence: 60 degree
Note: Use of controls or adjustments or performance of
procedure other than those specified herein, may result in
hazardous radiation exposure. Avoid direct exposure to
beam.
Safet
y
instruction, Warnin
g
& Notes
1-11

Warning
1.General
. All ICs and many other semiconductors are susceptible to
electrostatic discharges (ESD). Careless handing during
repair can reduce life drastically. Make sure that, during
repair, you are at the same potential as the mass of the
set by a wristband with resistance. Keep components and
tools at this same potential. Available ESD protection
equipment:
1) Complete kit ESD3 (small tablemat, wristband,
connection box, extension cable and earth cable)
4822 310 10671.
2) Wristband tester 4822 344 13999.
. Be careful during measurements in the live voltage
section. The primary side of the power supply , including
the heat sink, carries live mains voltage when you
connect the player to the mains (even when the player is
“off”!). It is possible to touch copper tracks and/or
components in this unshielded primary area, when you
service the player. Service personnel must take
precautions to prevent touching this area or components
in this area. A “lighting stroke” and a stripe-marked
printing on the printed wiring board, indicate the primary
side of the power supply.
. Never replace modules, or components, while the unit is
“on”.
2. Laser
. The use of optical instruments with this product, will
increase eye hazard.
. Only qualified service personnel may remove the cover
or attempt to service this device, due to possible eye
injury.
. Repair handing should take place as much as possible
with a disc loaded inside the player.
. Text below is placed inside the unit, on the laser cover
shield:
Notes: Manufactured under licence from Dolby
Laboratories. The double-D symbol is trademarks of Dolby
Laboratories, Inc. All rights reserved.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN, AVOID EXPOSURE
TO BEAM.
1-12

 6HUYLFH+LQWV
 &$87,21
&+$5*('&$3$&,7256217+(6(592%2$5'0$<'$0$*(7+('5,9(
(/(&7521,&6:+(1&211(&7,1*$1(:'5,9(7+$7¶6:+<%(6,'(67+(6$)(7<
0($685(6/,.(
  6:,7&+2))32:(56833/<
  (6'3527(&7,21
$'',7,21$/$&7,2160867%(7$.(1%<7+(5(3$,57(&+1,&,$1
 7KHIROORZLQJVWHSVKDYHWREHGRQHZKHQUHSODFLQJWKHGHIHFWLYHORDGHU

  'LVPDQWOLQJRIWKHORDGHUWRDFFHVVWKH(6'SURWHFWLRQSRLQWLIQHFHVVDU\
   6ROGHUWKH(6'SURWHFWLRQSRLQW    
  'LVFRQQHFWÀH[IRLOFDEOHIURPWKHGHIHFWLYHORDGHU
  3XWDSDSHUFOLSRQWKHÀH[IRLOWRVKRUWFLUFXLWWKHFRQWDFWV¿J
  5HSODFHWKHGHIHFWLYHORDGHUZLWKDQHZORDGHU
  5HPRYHSDSHUFOLSIURPWKHÀH[IRLODQGFRQQHFWLWWRWKHQHZORDGHU
  5HPRYHVROGHUMRLQWRQWKH(6'SURWHFWLRQSRLQW

$77(17,217KHODVHUGLRGHRIWKLVORDGHULVSURWHFWHGDJDLQVW(6'E\DVROGHUMRLQWZKLFKVKRUWFLUFXLWVWKHODVHUGLRGHWRJURXQG
)RUSURSHUIXQFWLRQDOLW\RIWKHORDGHUWKLVVROGHUMRLQWPXVWEHUHPRYHDIWHUFRQQHFWLRQORDGHUWRWKHVHW



 2QO\DSSOLFDEOHIRUGHIHFWLYHORDGHUQHHGHGWREHVHQWEDFNWRVXSSOLHUIRUIDLOXUHDQDO\VLVDQGWRVXSSRUWEDFNFKDUJLQJ 
 HYLGHQFH
 7KLVLVDOVRDSSOLFDEOHIRUDOOSDUWQHUVKLSZRUNVKRSV
(6'SURWHFWLRQSRLQWLVDFFHVVLEOHIURPWRSRIORDGHU
Solder Join
t
1-13

Lead-Free requirement for service
INDENTIFICATION:
Regardless of special logo (not always indicated)
One must treat all sets from 1.1.2005 onwards, according
next rules.
Important note: In fact also products a little older can also
be treated in this way as long as you avoid mixing
solder-alloys (leaded/ lead-free). So best to always use
SAC305 and the higher temperatures belong to this.
Due to lead-free technology some rules have to be
respected by the workshop during a repair:
xUse only lead-free solder alloy Philips SAC305 with
order code 0622 149 00106. If lead-free solder-paste is
required, please contact the manufacturer of your
solder-equipment. In general use of solder-paste within
workshops should be avoided because paste is not easy
to store and to handle.
xUse only adequate solder tools applicable for lead-free
solder alloy. The solder tool must be able
oTo reach at least a solder-temperature of 400°C,
oTo stabilize the adjusted temperature at the
solder-tip
oTo exchange solder-tips for different applications.
xAdjust your solder tool so that a temperature around
360°C – 380°C is reached and stabilized at the solder
joint. Heating-time of the solder-joint should not exceed
~ 4 sec. Avoid temperatures above 400°C otherwise
wear-out of tips will rise drastically and flux-fluid will be
destroyed. To avoid wear-out of tips switch off un-used
equipment, or reduce heat.
xMix of lead-free solder alloy / parts with leaded solder
alloy / parts is possible but PHILIPS recommends
strongly to avoid mixed
solder alloy types (leaded and lead-free). If one cannot
avoid, clean carefully the
solder-joint from old solder alloy and re-solder with new
solder alloy (SAC305).
xUse only original spare-parts listed in the
Service-Manuals. Not listed standard-material
(commodities) has to be purchased at external
companies.
xSpecial information for BGA-ICs:
- always use the 12nc-recognizable soldering
temperature profile of the specific BGA (for
de-soldering always use highest lead-free
temperature profile, in case of doubt)
- lead free BGA-ICs will be delivered in so-called
‘dry-packaging’ (sealed pack including a silica gel
pack) to protect the IC against moisture. After
opening, dependent of MSL-level seen on
indicator-label in the bag, the BGA-IC possibly
still has to be baked dry. This will be
communicated via AYS-website.
Do not re-use BGAs at all.
xFor sets produced before 1.1.2005, containing
leaded soldering-tin and components, all needed
spare-parts will be available till the end of the
service-period. For repair of such sets nothing
changes.
xOn our website:
www.atyourservice.ce.Philips.com
You find more information to:
BGA-de-/soldering (+ baking instructions)
Heating-profiles of BGAs and other ICs used in
Philips-sets
You will find this and more technical information
within the “magazine”, chapter “workshop news”.
For additional questions please contact your local
repair-helpdesk.
Notes
1-14

User Manual
Audio/Video FMHDMI
* Adaptador fornecido como acessório não deverá ser usado nas redes elétricas do Brasil, seu uso é destinado exclusivamente a
outros países da América Latina.
The following excerpt of the Quick Start Guide serves as an introduction to the set.
The complete Direction For Use can be download in different languages from
Philips Customer Contact & Support site: www.p4c.philips.com
2-1
QSG for HTS3520/12/05/55/51/X78/94/98
HDMI Cable for /55/X78, and Power socket transition for /55.

1
1
2-2

SUBWOOFER
REAR
LEFT
REAR
RIGHT
FRONT
RIGHT
FRONT
LEFT
FRONT
CENTER
2
3FM
Cable
2-3

5
1
6
4
AAA
x 2
2
HDMI
Cable
Audio
Cable
2-4

2
USB Settings
TV
HDMI
1
General Setup
General Setup
Screen Saver
Sleep Timer
Display Dim
Disc Lock
DivX(R) VOD Code
Português
English
Español
Auto
OSD Language
2
5
3
6
2-5

3
1
2
3
4
3
1
2
2-6