Philips Colgate SonicPro 70 User manual

SonicPro 70

1
2
11
12
4
3
5
6
7
8
9
10
1

English 6
Español 26
Português do Brasil 46

English
6English
Introduction
Congratulations on your new Philips Colgate SonicPro power toothbrush!
Superior plaque removal, whiter teeth and healthier gums are at your
fingertips. Using a combination of gentle sonic technology and clinically
developed and proven features, you can be confident that you’re getting
the very best clean, every time. Further support and product registration
are available to you at: www.philips.com/welcome.
Welcome to the Philips Colgate SonicPro family!
Intended Use
Philips Colgate SonicPro power toothbrushes are intended to remove
adherent plaque and food debris from the teeth to reduce tooth decay
and improve and maintain oral health. They are intended for consumer
home use. Use by children should be with adult supervision.
Important safety information
Only use the product for its intended purpose. Read this important
information carefully before you use the product and its batteries and
accessories, and save it for future reference. Misuse can lead to hazards or
serious injuries.
Danger
- Keep the charger away from water. Do not place or store the appliance
where it can fall or be pulled into a tub or sink.
- Do not immerse the charger in water or any other liquid.
- After cleaning, make sure the charger is completely dry before you
connect it to the wall socket.
Warning
- This appliance can be used by children and persons with reduced
physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the
hazards involved. Cleaning and user maintenance shall not be made by
children without supervision.
- Children shall not play with the appliance.
- If the appliance is damaged in any way (brush head, toothbrush handle
and charger), stop using it.
- The mains cord cannot be replaced. If the mains cord is damaged,
discard the charger.

7
English
- Always replace the charger with one of the original type in order to
avoid a hazard.
- This appliance contains no user-serviceable parts. If the appliance is
damaged, contact the Consumer Care Center in your country (see
'Warranty and support').
- Keep the cord away from heated surfaces.
- Do not use the charger outdoors or near heated surfaces.
Caution
- Do not clean the brush head, handle, or charger in the dishwasher.
- If you have had oral or gum surgery in the previous 2 months, consult
your dentist before you use this appliance.
- Consult your dentist if excessive bleeding occurs after using this
appliance or if bleeding continues to occur after 1 week of use. Also
consult your dentist if you experience discomfort or pain when you use
this appliance.
- This Philips Colgate SonicPro toothbrush complies with the safety
standards for electromagnetic devices. If you have a pacemaker or
other implanted device, contact your physician or the device
manufacturer of the implanted device prior to use.
- If you have medical concerns, consult your doctor before you use this
appliance.
- This appliance has only been designed for cleaning teeth, gums and
tongue. Do not use it for any other purpose. Stop using the appliance
and contact your doctor if you experience any discomfort or pain.
- This appliance is a personal care device and is not intended for use on
multiple patients in a dental practice or institution.
- Do not use other brush heads than the ones recommended by Philips
Colgate SonicPro.
- Stop using a brush head with crushed or bent bristles. Replace the
brush head every 3 months or sooner if signs of wear appear.
- Avoid direct contact with products that contain essential oils or
coconut oil. Contact may result in bristles dislodging.
Battery safety instructions
- Only use original Philips accessories or consumables. Only use
detachable supply unit HX6100.
- Charge, use and store the product at a temperature between 0°C and
40°C.
- Keep product and batteries away from fire and do not expose them to
direct sunlight or high temperatures.

8English
- If the product becomes abnormally hot or smelly, changes color or if
charging takes longer than usual, stop using and charging the product
and contact Philips.
- Do not place products and their batteries in microwave ovens or on
induction cookers.
- Do not open, modify, pierce, damage or dismantle the product or
battery to prevent batteries from heating up or releasing toxic or
hazardous substances. Do not short-circuit, overcharge or reverse
charge batteries.
- If batteries are damaged or leaking, avoid contact with the skin or eyes.
If this occurs, immediately rinse well with water and seek medical care.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable standards and
regulations regarding exposure to electromagnetic fields.
Radio Equipment Directive
Hereby, Philips declares that electric toothbrushes with radio frequency
interface (Bluetooth) are in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address: www.philips.com/support
The radio frequency interface in this product operates at 13.56MHz.
The maximum RF power transmitted by the appliance is 30.16dBm.
Your SonicPro (Fig. 1)
1 Brush head cap
2 Smart brush head(s)
3 Handle
4 Power on/off button
5 Intensity light
6 Mode/intensity button
7 Modes
8 Brush head replacement reminder light
9 Battery indicator lights
10 Charger
11 Travel case *
12 Micro USB cable *
* Note: The content of the box may vary based on the model
purchased.

9
English
Using your SonicPro
Brushing instructions
1Push the brush head firmly onto the handle. Wet bristles and apply
toothpaste.
Note: It is normal to see a slight gap between the brush head and the
handle. This allows the brush head to vibrate properly.
2Place the toothbrush bristles against the teeth at a slight angle (45
degrees), pressing firmly to make the bristles reach the gumline or
slightly beneath the gumline.
Note: Keep the center of the brush in contact with the teeth at all
times.
3Press the power on/off button to turn on the toothbrush.
45°
4Apply light pressure to maximize SonicPro’s effectiveness and let the
toothbrush do the brushing for you. Gently move the brush head
slowly across the teeth in a small back and forth motion so the longer
bristles reach between your teeth. Continue this motion throughout the
brushing cycle.

10 English
Note: To learn how to brush with specific modes, see ‘Modes’.
5To clean the inside surfaces of the front teeth, tilt the brush handle
semi-upright and make several vertical overlapping brushing strokes
on each tooth.
Note:
- A change in vibration from the handle alerts you when you apply too
much pressure (see Pressure sensor).
- Your toothbrush is safe to use on braces, dental moderations and
dental restorations (fillings, crowns, veneers).
- Do not use your power toothbrush in the shower.
Brush head
Your SonicPro comes with the 2-in-1 brush head for healthier gums and a
deep clean. This brush head is equipped with the BrushSync technology.

11
English
Note: Your tootbrush is compatible with all other Philips Colgate SonicPro
brush heads.
BrushSync Technology
BrushSync technology enables your brush heads to communicate with
your handle using a microchip. This enables the following features:
- Brush head mode pairing
- Brush head replacement reminder
Brushing modes
Your power toothbrush is equipped with up to 4 different modes*: Clean,
Deep Clean+, White+* and Gum health*.
Based on the smart brush head you use, the mode will be selected
automatically.
To manually change the mode, press the mode/intensity button while the
toothbrush is off.
* Note:
- The type and number of modes vary based on the model purchased.
- All brush heads work with each mode.

12 English
- When the Philips Colgate SonicPro toothbrush is used in clinical studies,
it must be used at high intensity, with the EasyStart feature turned off.
Brush head mode pairing
Brush heads with BrushSync technology are equipped with a microchip
which communicates to the handle and automatically pairs it with the
recommended mode and intensity.
Note: If you change modes/intensity, the brush head will remember the
last used setting. If you wish to brush with the recommended setting, you
can find the recommended mode/intensity in ‘Brushing Modes’.
Clean and
Deep Clean+
White+ Gum Health
Benefit Plaque
removal Plaque and surface stain
removal
Plaque
removal and
gum massage
Recommended
intensity level
3 3 3
Total brushing time Clean: 2
minutes
Deep Clean: 3
minutes*
2 minutes and
40 seconds 3 minutes and 20 seconds

13
English
Clean and
Deep Clean+
White+ Gum Health
How to brush Clean: Brush
each segment
for 20 seconds
1
2
3
4
5
6
Deep Clean+:
Brush each
segment for
30 seconds
1
2
3
4
5
6
Brush each
segment for
20 seconds,
1
2
3
4
5
6
then brush
segments 1
and 2 for 20
seconds each.
1
2
Brush each
segment for
20 seconds,
1
2
3
4
5
6
then brush
segments 1, 2,
3 and 4 for 20
seconds each.
1
2
4
3
*Note:
- The modes and brush head type vary based on the model purchased.
- When brushing with the Philips Colgate SonicPro App in 'Deep Clean'
mode, the brushing time is 2 minutes.
Intensity settings
Your power toothbrush comes with 3 different intensity settings: low,
medium and high. When attached to the handle, the smart brush head will
automatically select the recommended intensity. To manually change the
intensity, turn on the handle and press the mode/intensity button.
While toothbrush is ON, press this button to change intensity setting.

14 English
Features
- EasyStart
- Connected Brush experience
- Brush head replacement reminder
- Pressure sensor
- BrushPacer
EasyStart
The EasyStart feature gently increases the power of the handle over the
first 14 brushings to help you get used to the brushing power.
The EasyStart feature works with all modes.
Note: Your toothbrush comes with the EasyStart feature deactivated. To
activate EasyStart, see 'Activating or deactivating features'.
Philips Colgate SonicPro app - Connected brushing
experience
The Philips Colgate SonicPro app pairs with your toothbrush to provide
you with interactive brushing features. By brushing with your Philips
Colgate SonicPro app account, you will be able to:
- Receive brushing suggestions and personalized feedback
- Track your brushing progress over time
To start using the connected brushing features:
1Download the Philips Colgate SonicPro app to your phone.
2Follow the steps in the app setup.
3Pair your toothbrush with the app.

15
English
4Create your account.
5Personalize your app by answering questions about your brushing
habits and interests.
6Start your connected brushing experience.
Note: Make sure your phone’s Bluetooth is turned on when using the
connected brushing features.
Note: If you have any questions while setting up your account, be sure to
review the Philips Colgate SonicPro Privacy Statement, available
throughout the app setup process.
How to brush with the app
1Go to the brushing screen in the app and select 'Start Brushing'.
2First brushing starts on the upper right molar. You can customize your
starting location in 'Settings'.
3Follow the brushing guidance.
Tip: To ensure the best performance of the brushing sensors, keep your
head facing forward.
4Gently begin brushing. The app will highlight the correct segment. The
timer will help you keep track.
5Move your brush head when the highlighted segment changes.
6Repeat, until you finish brushing all segments.
7When you have finished brushing, review and touch up any missed
areas. Follow the in-app instructions on how to use the touch-up
feature.
Brush head replacement reminder
Over time, the handle tracks the wear of your smart brush head by
measuring:
- The overall pressure you apply while brushing.
- The total time you have brushed with your brush head.
Once your brush head is no longer effective, the brush head replacement
reminder will flash amber. This indicates that it is recommended to replace
your brush head.

16 English
Note: Your tootbrush comes with the brush head replacement reminder
activated. To deactivate this feature, see 'Activating or deactivating
features'.
Pressure sensor
Your SonicPro measures the pressure you apply while brushing to protect
your gums and teeth from damage.
If you apply too much pressure, the handle changes its vibration until you
reduce the pressure.
Note: Your toothbrush comes with pressure sensor activated. To
deactivate this feature, see 'Activating or deactivating features'.
BrushPacer
The BrushPacer features indicates when you are supposed to move onto
the next section of your teeth via a brief change in vibration.
The toothbrush turns off automatically at the end of the brushing session.
Charging and battery status
Charging on the charger
1Plug the charger into an electrical outlet.
2Place the handle on the charger.
- When fully charged, all battery indicator lights light up green.
Note: Your handle comes pre-charged for first use. After first use, charge
for at least 24 hours.
Charging with the travel case
Note: Only the following SonicPro handles can be charged in the charging
travel case: HX972G, HX972K, HX972V, HX972P, HX962C. The HX number
can be found on the bottom of your handle.

17
English
Note: The charging travel case requires a USB adapter to charge the
handle. The USB adapter is not included.
1Connect the charging travel case to 5V DC input power either from:
- a UL-listed or certified to ANSI/UL 60950-1 personal computer's
standard USB connector or,
- a UL-listed or certified to ANSI/UL 60950-1 LPS power supply with
USB output port or,
- a UL-listed or certified 1310 Class 2 power supply.
The USB adapter must be a safe extra low voltage source,
compatible with the electrical ratings marked on the bottom of
the device.
2The travel case charges your toothbrush until it is fully charged.
- When fully charged, all battery lights light up green.
Note: Charging the handle with the charging travel case may take longer
than on the charger.
Battery status (handle on plugged in charger)
When the handle is placed on the charger or travel case, the battery
indicator lights flash green based on the current battery level.
Number of flashing lights Battery charge level
1 Low
2 Medium
3 High
Note: When the handle is fully charged, the three battery indicator lights
light up green. After 30 seconds the battery indicator lights switch off.

18 English
Battery status (when handle is not placed on charger)
When removing the handle from the charger or travel case, the battery
indicator lights indicate the status of the battery.
LED color Number of LEDs Battery charge level
Solid green 3 High
Solid green 2 Medium
Solid green 1 Low
Flashing amber 1 (with beeps) Empty or near empty
Activating or deactivating features
You can activate or deactivate the following features of your toothbrush:
- EasyStart
- Brush head replacement reminder
- Pressure sensor

19
English
Step 1: Place the handle on the charger
Step 2: Press and hold power button for:
EasyStart Brush head
replacement
reminder
Pressure sensor
Up to 3 seconds Up to 5 seconds Up to 7 seconds
¯ ¯ ¯
Step 3: Let go of the power button when you hear
1 beep 1 beep, 2 beeps
and then 3 beeps 1 beep and then 2 beeps
¯ ¯ ¯
If you see battery indicator lights flashing green 2 times and
hear low to high triple tones, then the feature has been
activated.
OR
If you see battery indicator lights flashing amber once and
hear high to low triple tones, then the feature has been
deactivated.

20 English
Cleaning
- All parts can be cleaned with a damp cloth or rinsed with warm water.
- Remove the brush head from the handle and rinse it thoroughly.
- Rinse the entire handle, especially the brush head connection, at least
once a week.
Caution: Do not push on the rubber seal at the top of the handle. Gently
clean around the rubber seal.