Philips 383810 User manual

5"
8
5/16"
Pulse Start Metal Halide 320 Watt
Clear Universal Lamp
■Ordering Information
Ordering Code MS320/U/PS
ANSI Designation M132/E
Prod ct N mber 383810
Description P lse Start Metal Halide
Package Q antity 12
■Ph sical Characteristics
B lb Size ED-28
B lb Finish Clear
Base (Nickel Plated Brass) Mog l-Screw
Max. Overall Length (MOL) 8 5/16'' (211mm)
Light Center Length (LCL) 5.0'' (127mm)
Arc Length 1.42'' (36mm)
Arc T be Material Q artz
Max. Permissible B lb Temp. 400ºC (752ºF)
Max. Permissible Base Temp. 210ºC (410ºF)
Max. B lb to Base Eccentricity 3º
Max.Arc T be to Base Eccentricity 3º
■Operating Characteristics (Photometric)
Vertical Horizontal
Rated Initial L mens 31,700 28,800
Mean L mens, Approximate 23,140 21,000
Rated Average Life, Ho rs 20,000 15,000
Correlated Color Temp. (CCT) 3900K 4300K
CIE Chromaticity,Approx. x-.389, y-.397 x-.374, y-.396
Color Rendering Index (CRI) 65 65
Efficacy (lpw) 99 90
■Operating Position
Universal–Enclosed L minaires Only
Note: P lse Start Metal Halide is Designed for Operation on Only Approved
Ballasts with Metal Halide P lse Ignitors.
MS320/U/PS
Lumen Maintenance Operated Base Up
BURNING HOURS
RATED AVERAGE LIFE 20,000 HOURS VERTICAL
100%
80%
60%
40%
20%
0%
0 2000 4000 6000 8000 10000
% LUMEN
MAINTENANCE

Electrical Data (Subject to change without notice)
Warnings, Cautions and Operating Instructions
“WARNING:These lamps can ca se serio s skin b rn and eye inflammation from
short wave ltraviolet radiation if o ter envelope of the lamp is broken or p nct red.
Do not se where people will remain for more than a few min tes nless adeq ate
shielding or other safety preca tions are sed. Certain lamps that will a tomatically
exting ish when the o ter envelope is broken or p nct red are commercially
available.” This lamp complies with FDA radiation performance standard 21
CFR s bchapter J. (USA:21CFR 1040.30 Canada:SOR/DORS/80-381)
If the o ter b lb is broken or p nct red, t rn off at once and replace the lamp to
avoid possible inj ry from hazardo s shortwave ltraviolet radiation. Do not scratch
the o ter b lb or s bject it to press re as this co ld ca se the o ter b lb to crack
or shatter.A partial vac m in the o ter b lb may ca se glass to fly if the envelope
is str ck.
WARNING:The arc-t be of metal halide lamps are designed to operate nder high
press re and at temperat res p to 1000º C and can nexpectedly r pt re d e to
internal or external factors s ch as a ballast fail re or misapplication. If the arc-t be
r pt res for any reason, the o ter b lb may break and pieces of extremely hot glass
might be discharged into the s rro nding environment. If s ch a r pt re were to
happen,THERE IS A RISK OF PERSONAL INJURY, PROPERTY DAMAGE, BURNS
AND FIRE.
Certain lamps that will retain all the glass particles sho ld inner arc-t be r pt re
occ r are commercially available from Philips Lighting Company.
RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE.
Allowing lamps to operate ntil they fail is not advised and may increase the
possibility of inner arc t be r pt re.
CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, PROPERTY
DAMAGE, BURNS AND FIRE RESULTING FROM AN ARC-TUBE RUPTURE THE
FOLLOWING LAMP OPERATING INSTRUCTIONS MUST BE FOLLOWED.
Lamp Operating Instructions:
1) T rn off lamps at least once a week for at least 15 min tes in systems which are
operating on a contin o s basis (24 ho rs/day, 7days/week). FAILURE TO TURN
OFF LAMPS FOR THE MINIMUM RECOMMENDED TIME MAY INCREASE THE
POSSIBILITY OF AN INNER ARC-TUBE RUPTURE.
2) RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE. Allowing lamps
to operate ntil they fail is not advised and may increase the possibility of inner arc
t be r pt re.
3) Use only in an enclosed fixt re capable of withstanding particles of glass having
temperat res p to 1000º C.
4) Before lamp installation/replacement, sh t power off and allow lamp and
fixt re to cool to avoid electrical shock and potential b rn hazards.
5) Use only a xiliary eq ipment meeting Philips and/or ANSI standards.
Use within voltage limits recommended by ballast man fact rer.
A. Operate lamp only within specified limits of operation.
B. For total s pply load refer to ballast man fact rers electrical data.
C. All P lse Start mog l based lamp req ire a socket rated to withstand
a 4000 volt p lse.
6) Periodically inspect the o ter envelope. Replace any lamps that show scratches,
cracks or damage.
7) If a lamp b lb s pport is sed, be s re to ins late the s pport electrically
to avoid possible decomposition of the b lb glass.
8) Protect lamp base, socket and wiring against moist re, corrosive atmospheres
and excessive heat.
9) Time sho ld be allowed for lamps to stabilize in color when t rned on for the
first time.This may req ire several ho rs of operation, with more than one start.
Lamp color is also s bject to change nder conditions of excess vibration or
shock, and color appearance may vary between individ al lamps.
10) Lamps may req ire 5 to 7 min tes to re-light if there is a power interr ption.
11) Take care in handling and disposing of lamps. If an arc t be is broken, avoid skin
contact with any of the contents or fragments.
12) Use this lamp only in fixt res that contain a P lse Start metal halide ballast and
are specifically designed for se with P lse Start metal halide lamps.
Philips Lighting Compan
200 Franklin Square Drive ■P.O. Box 6800
Somerset, NJ 08875-6800
1-800-555-0050
www.lighting.philips.com/nam
A Division of Philips Electronics North America Corporation
Updated 2/02 PSMH 003
Philips Lighting
281 Hillmount Road
Markham, Ontario L6C 2S3
A Division of Philips Electronics Limited
Lamp Watts (Nominal) . . . . . . . . . . . . . . . . . . . . . . . . . 320
Lamp Operating Voltage (rms) (Nominal). . . . . . . . . . . 132
Initial Lamp Voltage Range (rms). . . . . . . . . . . . . . . . . . 120-140
Lamp Operating C rrent (Amps) (rms) (Nominal). . . . 2.65
Lamp C rrent Crest Factor (Maxim m). . . . . . . . . . . . 1.6
Warm- p Time to 90% of O tp t . . . . . . . . . . . . . . . . 2 Min tes
Re-strike Time for Hot Lamp . . . . . . . . . . . . . . . . . . . . 5–7 Min tes
Ballast Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI M132
Ballast Open Circ it Voltage (Minim m) . . . . . . . . . . . . 250 RMS Min.
P lse Peak Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000 Min., 4000 Max.
P lse Width @ 90% Peak (micro sec) . . . . . . . . . . . . . 1.3
P lse Repetition Rate (Minim m) . . . . . . . . . . . . . . . . . 1x/1/2cycle
Minim m Operating Temperat re. . . . . . . . . . . . . . . . . -30ºC
Advance Transformer Ballast N mber . . . . . . . . . . . . . 71A5892
Pulse Start Metal Halide 320 Watt Clear Universal Lamp
Philips
Lighting
Compan