Philips CFI-08100 User manual

200 Franklin Square Drive
P.O. Box 6800
Somerset, NJ 08875-6800
A Division of
Lamp Material Data Sheet (LMDS)
Product: Philips Compact Fluorescent Lamps CFL-i – All Types
ALTO and non-ALTO: SLS, EL/, Genie, and FC Types (All base types)
Philips Lighting Company
LMDS #: CFI – 08100A
Date: 08/10/2009
Page 1 of 2
Section 1. Manufacturer and Contact Information
Philips Lighting Company Division of Philips Electronics North America Corporation
200 Franklin Square Drive
P.O. Box 6800
Somerset, NJ 08875-6800
24 HR Emergency Phone Number: [phone] CHEMTREC
Other Information Calls: [phone] Philips Lighting Technical Information
Section 2. Hazardous Ingredients/Identity Information
These lamps contain the following materials: Exposure Limits in Air
Material (CAS #) OSHA PEL ACGIH TLV PERCENTAGE
mg/m3 mg/m3 by weight
Phosphor Powder
(as Nuisance Dust) 15 10 <2.5%
Yttrium Oxide (as Yttrium) (1314-36-9) 1 1 <0.5%
Barium Carbonate (0513-77-9) 0.5 0.5 <0.1%
Manganese Carbonate (598-62-9) 5 5 <0.1%
Tin (7440-31-5) 0.1 0.1 <0.1%
Indium (7740-74-6) 0.1 <0.07%
Bismuth (7440-69-9) <0.005%
Mercury (7439-97-6) 0.1 0.025 ~0.025%
The Phosphor Powder materials are ceramic phosphors. The ceramics are Barium Aluminate and Yttrium Oxide. The
PEL and TLV are given where available for the base materials. There is no data for the ceramics as mixtures.
Section 3. Physical Properties
Not applicable to an intact lamp. These items are light bulbs in various shapes, configurations, and designs. All contain a
small fluorescent tube (either twisted or bent to shape), a plastic housing (containing an electronic circuit to start the
lamp), and a threaded base for use in standard incandescent lamp sockets (or a pin base for use in a GU24 socket).
Some lamps utilize a glass, or plastic, outer envelop to enclose the fluorescent tube.
Section 4. Fire and Explosion Hazards
Not applicable to an intact lamp. If subjected to extreme heat, the plastic and glass components of the lamp may crack
or melt and the lamp may emit toxic fumes.
Tel: [phone] Philips Electronics North American Corporation

Section 5. Reactivity
Not applicable to an intact lamp.
Section 6. Health Hazards
Not applicable to an intact lamp. Breakage of the lamp may result in some exposure to the phosphor powder and to
elemental mercury. No adverse effects are expected from occasional exposure to broken lamps, but as a matter of good
practice, prolonged exposure should be avoided through the use of adequate ventilation during the disposal of large
quantities of lamps.
Emergency and First Aid Procedures: Apply normal first aid for glass cuts if such should occur through lamp breakage.
Section 7. Lamp Disposal Procedures
Normal precautions should be taken for the collection of glass particles in the event a lamp is broken.
Waste Disposal Method: All compact fluorescent lamps contain some amount of mercury. When a compact fluorescent
lamp is to be disposed, it is subject to the current EPA Toxicity Characteristic Leaching Procedure (TCLP) disposal
criteria. This test is used to determine if an item can be managed of as hazardous or non-hazardous waste.
Philips low-mercury ALTO compact fluorescent lamps are identifiable by their characteristic green logo. Philips ALTO
lamps are TCLP compliant and can be managed as non-hazardous waste. Philips will provide TCLP test data upon
request.
Philips non-ALTO lamps (with black logo) are not TCLP compliant and should be managed as a hazardous waste under
the EPA Universal Waste Rules for fluorescent lamps.
All disposal options should be evaluated with respect to federal, state, and local requirements. Before disposing of waste
lamps, check with federal, state, and/or local officials for current guidelines and regulations. Philips encourages recycling
of its products through qualified recycling facilities.
Section 8. Control Measures
Respiratory Protection: None. NIOSH-approved respirator should be used if large quantities of lamps are being broken
for disposal.
Ventilation: Avoid inhalation of any airborne dust. Provide local exhaust when disposing of large quantities of lamps.
Hand and Eye Protection: Appropriate hand and eye protection should be worn when disposing of lamps and/or handling
broken glass.
Section 9. Regulatory Information
As a product, these mercury-containing lamps, when shipped in the manufacturer’s original packaging, are not regulated
by air, truck, or ocean shipment. As a waste, these lamps may be regulated in various states and local communities.
This safety data sheet does not constitute “knowledge of the waste” in certain jurisdictions.
This document supercedes previous document: LMDS CFI-08100 issued on 06/08/08.
Occupational Health and Safety Administration (OSHA) Material Safety Data Sheet (MSDS) requirements for materials
are not applicable to manufactured articles in which individuals would not be subjected to materials contained in the article
during its normally intended use. The information in this document is provided as a courtesy and is intended to provide
relevant information in the event the articles it covers are encountered during unintended, or abnormal, circumstances.