Philips GC4340/02 User manual

Azur
GC4340, GC4330, GC4325, GC4320, GC4310

2

ENGLISH 4
ESPAÑOL 13
ITALIANO 23
PORTUGUÊS 32
 42
TÜRKÇE 52
GC4340, GC4330, GC4325, GC4320, GC4310

Important
Read these instructions for use carefully before using the appliance and
save them for future reference.
◗Check if the voltage indicated on the type plate corresponds to
the local mains voltage before you connect the appliance.
◗Only connect the appliance to an earthed wall socket.
◗Do not use the appliance if the plug, the cord or the appliance
itself shows visible damage, or if the appliance has been dropped
or is leaking.
◗Check the cord regularly for possible damage.
◗If the mains cord is damaged, it must be replaced by Philips, a
service centre authorised by Philips or similarly qualified persons
in order to avoid a hazard.
◗Never leave the appliance unattended when it is connected to the
mains.
◗Never immerse the iron and the stand, if provided, in water.
◗Keep the appliance out of the reach of children.
◗The soleplate of the iron can become extremely hot and may
cause burns if touched.
◗Do not allow the cord to come into contact with the soleplate
when it is hot.
◗When you have finished ironing, when you clean the appliance,
when you fill or empty the water tank and also when you leave
the iron even for a short while: set the steam control to position
0, put the iron on its heel and remove the mains plug from the
wall socket.
◗Always place and use the iron and the stand, if provided, on a
stable, level and horizontal surface.
◗Do not put perfume, vinegar, starch, descaling agents, ironing aids
or other chemicals in the water tank.
◗This appliance is intended for household use only.
Before first use
C1Remove the heat-resistant protective cover from the soleplate
(GC4340 only). Remove any sticker or protective foil from the
soleplate.
BThe iron may give off some smoke when you use it for the first time.This
will cease after a short while.
ENGLISH4

Preparing for use
Filling the water tank
Never immerse the iron in water.
1Make sure the appliance is unplugged.
C2Set the steam control to position 0 (= no steam).
3Open the cap of the filling opening.
4Tilt the iron backwards.
C5Fill the water tank with tap water up to the maximum level by
means of the filling cup.
Do not fill the tank beyond the MAX indication.
Do not put perfume, vinegar, starch, descaling agents, ironing aids or
other chemicals in the water tank.
◗If the tap water in your area is very hard, we advise you to mix it
with an equal portion of distilled water, or to use distilled water
only.
C6Close the cap of the filling opening ('click').
Setting the temperature
C1Type GC4340 only: remove the heat-resistant protective cover.
Do not leave the heat-resistant protective cover on the soleplate
during ironing.
2Put the iron on its heel.
ENGLISH 5

C3Set the required ironing temperature by turning the
temperature dial to the appropriate position.
Check the laundry care label for the required ironing temperature:
-1Synthetic fabrics (e.g. acrylic, nylon, polyamide, polyester)
-1Silk
-2Wool
-3Cotton, linen
If you do not know what kind or kinds of fabric an article is made of,
determine the right ironing temperature by ironing a part that will not
be visible when you wear or use the article.
Silk, woollen and synthetic materials: iron the reverse side of the fabric
to prevent shiny patches.Avoid using the spray function to prevent
stains.
Start ironing the articles that require the lowest ironing temperature,
such as those made of synthetic fibres.
4Put the mains plug in an earthed wall socket.
C5When the amber temperature light has gone out, wait a while
before you start ironing.
The temperature light will go on from time to time during ironing.
Using the appliance
Steam ironing
1Make sure that there is enough water in the water tank.
2Select the recommended ironing temperature (see chapter
'Preparing for use', section 'Setting the temperature').
C3Select the appropriate steam setting. Make sure that the steam
setting you select is suitable for the ironing temperature
selected:
- 1 - 3 for moderate steam (temperature settings 2to 3)
- 4 - 6 for strong steam (temperature settings 3to MAX)
BThe iron will start steaming as soon as the set temperature has been
reached.
ENGLISH6
LINEN
SILK
NYLON
WOOL
COTTON
MIN
MAX

Ironing without steam
C1Set the steam control to position 0 (= no steam).
2Select the recommended ironing temperature (see chapter
'Preparing for use', section 'Setting the temperature').
Features
Delicate fabric protector (GC4325 only)
The delicate fabric protector protects delicate fabrics from heat
damage and shiny patches.
With the delicate fabric protector you can iron delicate fabrics (silk,
wool and nylon) at temperature settings 3to MAX in combination
with all steam functions available on the iron.
The delicate fabric protector reduces the soleplate temperature
instantly, thus allowing you to iron delicate fabrics safely.
If you do not know what kind or kinds of fabric an article is made of,
determine the right ironing temperature by ironing a part that will not
be visible when you wear or use the article.
C1Put the iron on the delicate fabric protector ('click').
Spray function
You can use the spray function to remove stubborn creases at any
temperature.
1Make sure that there is enough water in the water tank.
C2Press the spray button several times to moisten the article to
be ironed.
Concentrated shot of steam from the special Steam Tip
A powerful shot of concentrated steam helps remove stubborn
creases.The forward-directed concentrated shot of steam enhances
the distribution of steam into every part of your garment.
The shot-of-steam function can only be used at temperature settings
between 2and MAX.
ENGLISH 7

C1Press and release the shot-of-steam button.
Vertical shot of steam
C1The shot-of-steam function can also be used when you hold
the iron in vertical position.
This is useful for removing creases from hanging clothes, curtains etc.
Never direct the steam at people.
Drip stop
This iron is equipped with a drip-stop function: the iron automatically
stops producing steam when the temperature is too low, to prevent
water from dripping out of the soleplate.When this happens you may
hear a sound.
Automatic anti-calc system
C1The built-in anti-calc system reduces the build-up of scale and
guarantees a longer life for the iron.
Electronic safety shut-off function (GC4325/4320 only)
C◗The electronic safety shut-off function automatically switches off
the iron if it has not been moved for a while.
◗The red auto-off light starts blinking to indicate that the iron has
been switched off by the safety shut-off function.
To let the iron heat up again:
- Pick up the iron or move it slightly.
- The red auto-off light goes out. If the temperature of the soleplate
has dropped below the set ironing temperature, the amber
temperature light goes on.
ENGLISH8

- If the temperature light goes on after you have moved the iron, wait
for it to go out before you start ironing.
- If the temperature light does not go on after you move the iron, the
soleplate still has the right temperature and the iron is ready for use.
Alert light and electronic safety shut-off function (GC4340
and GC4330)
The iron is equipped with a blue alert light.
C◗The blue alert light burns as long as the iron is plugged in.
◗The blue alert light starts blinking to indicate that the iron has
been switched off by the safety shut-off function.
To let the iron heat up again:
- Pick up the iron or move it slightly.
- The blue alert light stops blinking. If the temperature of the soleplate
has dropped below the set ironing temperature, the amber
temperature light goes on.
- If the temperature light goes on after you have moved the iron, wait
for it to go out before you start ironing.
- If the temperature light does not go on after you move the iron, the
soleplate still has the right temperature and the iron is ready for use.
Cleaning and maintenance
After ironing
1Remove the mains plug from the wall socket and let the iron
cool down.
2Wipe flakes and any other deposits off the soleplate with a
damp cloth and a non-abrasive (liquid) cleaning agent.
To keep the soleplate smooth, you should avoid hard contact with
metal objects. Never use a scouring pad, vinegar or other chemicals to
clean the soleplate.
3Clean the upper part of the iron with a damp cloth.
4Regularly rinse the water tank with water. Empty the water
tank after cleaning.
Calc-clean function
You can use the calc-clean function to remove scale and impurities.
◗Use the calc-clean function once every two weeks. If the water in
your area is very hard (i.e. when flakes come out of the soleplate
ENGLISH 9

during ironing), the calc-clean function should be used more
frequently.
1Make sure the appliance is unplugged.
2Set the steam control to position 0.
3Fill the water tank to the maximum level.
Do not put vinegar or other descaling agents in the water tank.
C4Select the maximum ironing temperature.
5Put the plug in an earthed wall socket.
6Unplug the iron when the amber temperature light has gone
out.
C7Hold the iron over the sink, press and hold the calc-clean
button and gently shake the iron to and fro.
Steam and boiling water will come out of the soleplate. Impurities and
flakes (if any) will be flushed out.
8Release the calc-clean button as soon as all the water in the
tank has been used up.
Repeat the calc-clean process if the iron still contains a lot of impurities.
After the calc-clean process
- Put the plug in the wall socket and let the iron heat up to allow the
soleplate to dry.
- Unplug the iron when it has reached the set ironing temperature.
- Move the hot iron gently over a piece of used cloth to remove any
water stains that may have formed on the soleplate.
- Let the iron cool down before you store it.
Storage
1Unplug the iron and set the steam control to position 0.
C2Empty the water tank.
ENGLISH10
LINEN
SILK
NYLON
WOOL
COTTON
MIN
MAX