Philips ShoqBox SB300 User manual

SB300
Register your product and get support at
www.philips.com/support
User manual
Portable speaker

1EN
Contents
1 Important 1
2 Your portable speaker 2
Introduction 2
What's in the box 2
Overview of the speaker 2
3 Get started 4
Charge the built-in battery 4
Turn on/o 4
4 Play from Bluetooth devices 5
Connect a device 5
Play from a Bluetooth-enabled
device 5
Control your phone call 6
Reconnect a device 6
Disconnect a device 6
Connect another device 6
Clear Bluetooth pairing information 6
5 Other features 7
Play from external devices 7
Turn the ashing light on/o 7
Adjust volume 7
6 Specications 8
7 Troubleshooting 9
General 9
About Bluetooth device 9
8 Notice 10
Compliance 10
Care of the environment 10
Trademark notice 11

1EN
1 Important
Warning
•Never remove the casing of this speaker.
•Never place this speaker on other electrical
equipment.
•Keep this speaker away from direct
sunlight, naked ames or heat.
• Only use attachments or
accessories specied by the
manufacturer.
• The battery shall not be exposed
to excessive heat such as sunshine,
re or the like.
• Do not place any sources of
danger on the speaker (e.g. lighted
candles).
• The speaker can meet IPX7
waterproof standard only when
the DC IN/AUDIO IN socket cover is
covered seamlessly.
• The speaker supports USB V2.0 or
V1.1 only.
Note
•The type plate is located on the back of the
speaker.

2EN
2 Your portable
speaker
Congratulations on your purchase, and
welcome to Philips! To fully benet from
the support that Philips oers, register
your product at www.philips.com/
welcome.
Introduction
With this speaker, you can enjoy audio
from Bluetooth-enabled devices or
other external devices.
What's in the box
Check and identify the contents of your
package:
• Speaker
• USB cable for charging
• Printed materials
Quick Start Guide
Overview of the speaker
1
2
3
4
5
6
8
7
a Bluetooth Indicator
• Indicate Bluetooth connection
status.
b +/-
• Adjust volume.
c Battery indicator
• Indicate battery status.
d
• Turn the speaker on or o.
e
• While playing, turn the ashing
light on or o.

3EN
f
• Enter Bluetooth pairing mode.
• After Bluetooth connection,
respond to an incoming call.
• Clear Bluetooth pairing
information.
g DC IN
• Charge the built-in battery.
h AUDIO IN
• Connect an external audio
device.

4EN
3 Get started
Always follow the instructions in this
chapter in sequence.
Charge the built-in
battery
The speaker is powered by a built-in
rechargeable battery.
Note
•The micro USB socket is for charging only.
•Rechargeable battery has a limited number
of charge cycles. Battery life and number of
charge cycles vary by use and settings.
1 Flip open the cover on the back of
the speaker.
2 Connect the speaker to AC power
by using the adaptor (not supplied).
The battery LED indicator indicates the
battery status.
Battery Status Battery Indicator
Under charging Solid red
Low battery Flashing red for 10
minutes, then no
light
Fully charged O
Turn on/o
• To turn on the speaker, press and
hold until the blue LED indicator
ashes.
• To turn o the speaker, press and
hold until the blue LED indicator
turns o.
Note
•The speaker switches to standby mode
automatically when being idle for 15
minutes.

5EN
4 Play from
Bluetooth
devices
With this speaker, you can listen to
audio from Bluetooth-enabled devices.
Connect a device
Note
•Any obstacle between this speaker
and a Bluetooth device can reduce the
operational range.
•Keep away from any other electronic
device that may cause interference.
•The operational range between this
speaker and a Bluetooth device is
approximately 10 meters (30 feet).
1 Make sure that the speaker is in
Bluetooth pairing mode.
• For rst-time use, the
speaker enters pairing mode
automatically.
• If the speaker has been paired with
other device before, press and
hold on the speaker for three
seconds to enter pairing mode.
» The Bluetooth indicator ashes
blue quickly.
3 sec.
2 On your Bluetooth device, enable
Bluetooth and search for Bluetooth
devices that can be paired (refer to
the user manual of the device).
3 Select [Philips SB300] displayed
on your device for pairing and
connection. If necessary, input
“0000” as the pairing password.
» After successful pairing and
connection, the speaker beeps
twice, and the Bluetooth LED
indicator turns solid blue.
Bluetooth LED indicator (blue):
Bluetooth
Indicator
Bluetooth Connection
Status
Flashing
quickly (2Hz)
Pairing
Flashing
slowly (1Hz)
Connecting
Solid blue Connected
Play from a Bluetooth-
enabled device
After successful Bluetooth connection,
play audio on your Bluetooth device.
» Music streams from your Bluetooth
device to the speaker.
Philips SB300

6EN
Control your phone call
After Bluetooth connection, you can
control an incoming call with this
speaker.
Button Function
Press to answer an
incoming call.
Press and hold for three
seconds to reject an
incoming call.
During a call, press to end
the current call.
During a call, press and
hold for three seconds to
transfer the call between
your mobile device and the
speaker.
Note
•Music play pauses when there is an
incoming call, and resumes when your
phone call ends.
Reconnect a device
• When you turn on the speaker,
it tries to reconnect the last
connected device automatically;
• If not successful, select [Philips
SB300] on your Bluetooth menu to
start reconnection.
Disconnect a device
• Press and hold for three seconds;
• Turn o the speaker;
• Disable Bluetooth on your device;
or
• Move the device beyond the
communication range.
Connect another device
1 Press and hold for three seconds
to disconnect the currently
connected device.
» The speaker enters Bluetooth
pairing mode.
2 Connect another Bluetooth device.
Clear Bluetooth pairing
information
Press and hold for ten seconds to
clear Bluetooth pairing information.

7
Tip
•When you start music streaming from
a connected Bluetooth device, the
speaker switches to the Bluetooth source
automatically.
Turn the ashing light
on/o
While playing, press to turn the
ashing light on or o.
» When the light is turned on, its color
changes randomly.
Adjust volume
During play, press +/- repeatedly to
increase or decrease volume.
Tip
•You can press and hold +/- to increase or
decrease volume continuously.
•When the volume reaches the maximum,
the speaker beeps twice.
5 Other
features
Play from external
devices
With this speaker, you can also listen
to an external audio device such as an
MP3 player.
Note
•Make sure that music playback through
Bluetooth is stopped.
1 Flip open the cover on the back of
the speaker.
2 Connect an audio input cable (not
supplied) with a 3.5 mm connector
on both ends to
• the AUDIO IN socket on this
speaker, and
• the headphone socket on the
external device.
3 Play audio on the external device
(refer to its user manual).
» The speaker switches to the
AUDIO IN mode.
EN