Philips Elite SRP4219G/07 User manual

Remote
control
user manual
v2 9/21
SRP4219G/07
SRP4229B/07
Universal
Universelle
Audio/Video
Élite
SRP4229B_07 ENG Manual v2.indd 1SRP4229B_07 ENG Manual v2.indd 1 9/2/21 5:03 PM9/2/21 5:03 PM

2
Setup ................................................................................3
Button functions............................................................4
Programming your remote..........................................6
Direct Code Entry.....................................................6
Auto Code Search....................................................8
Controlling combo devices....................................9
Using your remote .......................................................10
Primary audio control...........................................10
Code identication.................................................11
Reset to factory settings.......................................11
Troubleshooting .......................................................... 12
90-day Limited Warranty.......................................... 12
FCC statement ............................................................. 13
Table of contents
For assistance with this
remote, scan here or visit:
byjasco.com/47597i
SRP4229B_07 ENG Manual v2.indd 2SRP4229B_07 ENG Manual v2.indd 2 9/2/21 5:03 PM9/2/21 5:03 PM

3
Your universal remote requires two (2) AAA
batteries (not included). Alkaline batteries are
recommended.
Battery installation
1. On the back of the remote, pull down on
the textured surface and slide battery cover
downward to remove.
2. Match the (+) and (-) marks on the batteries
to the (+) and (-) marks inside the battery
compartment, then insert two (2) AAA
batteries. Be sure to use fresh batteries.
3. Position battery cover slightly below opening
and push upward to lock into place.
NOTE:If your remote stops operating properly,
replace the batteries with new ones.
Battery precautions
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
• Always remove old, weak or worn-out
batteries promptly and recycle or dispose of
them in accordance with local and national
regulations.
Battery saver
Your remote automatically turns o if the buttons
are held down for more than 8 seconds. This will
save your batteries should your remote get stuck
in a place where the buttons remain depressed
(e.g., between sofa cushions).
Code saver
You have up to 10 minutes to change the batteries
in your remote without losing the codes you have
programmed.
Setup
SRP4229B_07 ENG Manual v2.indd 3SRP4229B_07 ENG Manual v2.indd 3 9/2/21 5:03 PM9/2/21 5:03 PM

4
SETUP
OK
INPUT
DVD
TV
STR
AUD
ENTER
112233
445566
778899
00
ABCD
VOL
CH
LAST
STREAM
EXIT 7
13
14
17
19
20
21
18
16
3
4
1
88
9 9
11 11
2
6
5
15
10
12
Button functions
SRP4229B_07 ENG Manual v2.indd 4SRP4229B_07 ENG Manual v2.indd 4 9/2/21 5:03 PM9/2/21 5:03 PM

5
1. Power - Turns devices ON/OFF
2. TV, STR, DVD, AUD - Selects the device
to control
3. Up/down/left/right menu navigation
4. Last channel - Returns to the previously
selected channel
5. Setup - Used to program the remote
6. Channel up/down
7. Home/Guide - Easily access features on
streaming devices, or Guide on cable/satellite
receivers
8. Info/Options - Displays on-screen show/
content information
9. Menu - Displays the on-screen menu
10. Record, play, stop, rewind, fast forward, pause
11. Numbers - Enter numbers for direct channel
selection
12. Dash (-) - Use to select digital channels,
e.g., 4.1
13. Enter - Some devices require enter to be
pressed after channel selection
14. ABCD - Access additional features for DVRs,
cable and satellite receivers
15. DVD/Blu-ray™open/close - Open/close a
player, or List features on cable/satellite
receivers
16. Exit -Exit on-screen menus
17. Streaming app hotkey - Access top apps like
Netix®, Amazon®Prime, Hulu®and more
18. Volume up/down
19. Mute - Mutes sound
20. Ok - Selects menu items for the controlled
device
21. Input - Selects video inputs
Button functions
SRP4229B_07 ENG Manual v2.indd 5SRP4229B_07 ENG Manual v2.indd 5 9/2/21 5:03 PM9/2/21 5:03 PM

6
Programming your remote
Your remote is designed to control multiple audio/
video devices. To use, you will need to program the
remote for your devices. There are two dierent
methods you can use to program the remote,
Direct Code Entry or Auto Code Search.
• The Direct Code Entry method is the
recommended method, as it is the simplest
and quickest method in most cases.
• The Auto Code Search method searches
through all the codes in the remote to nd a
code for your device.
NOTE:This remote comes preprogrammed for
Roku®boxes and Samsung TVs. Press TV for
Samsung TVs and STR for Roku boxes.
Direct Code Entry (recommended)
1. Locate the Code List included with
your remote. Find the section for the
type of device you wish to control,
(e.g., TV, STR, DVD, AUD). Locate the
brand of your device and circle all the
remote codes for the brand.
2. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns on.
Release the SETUP button. The red
light will remain on.
NOTE:The red light will either be a
small light at the top of the remote or
the power ON/OFF button.
3. Press and release the device button
on the remote for the type of device
you wish to control, (e.g., TV, STR,
DVD, AUD). The red light will blink
once and remain on.
NOTE:Any of the device buttons on the
remote can be programmed to control
any of your devices. For example, you
can use the AUX device button on the
remote to control a satellite receiver,
digital converter box, streaming media
player or any device category in the
Code List.
SETUP
SRP4229B_07 ENG Manual v2.indd 6SRP4229B_07 ENG Manual v2.indd 6 9/2/21 5:03 PM9/2/21 5:03 PM

7
Programming your remote
4. Use the number buttons on the
remote to enter the rst 4-digit
remote code you circled in the
Code List in Step 1. The red light
will turn o after entering the
fourth digit
5. Point the remote at the device.
Test the buttons on the remote to
see if the device responds as you
would expect. If the buttons do not
operate the device, return to Step 2
above and use the next code that
you circled for that device.
6. Repeat steps 1 – 5 for each device you wish
to control.
Programming notes:
• Some codes may operate only a few functions
of your device. There may be another code in
the Code List that controls more functions.
Test other codes in the Code List for more
functionality.
• If you do not nd a remote code that works
your device or there are no codes in the
Code List for your device, use the Auto Code
Search method in the next section to program
your remote.
• For combination devices such as a TV/DVD
combo or TV/VCR combo, you may have to
enter a code for each device.
• Write down the remote codes used to
program the remote for future reference.
112233
445566
778899
00
SRP4229B_07 ENG Manual v2.indd 7SRP4229B_07 ENG Manual v2.indd 7 9/2/21 5:03 PM9/2/21 5:03 PM

8
Programming your remote
1. Manually turn on the device you
wish to control.
NOTE:The Auto Code Search process
cannot be used for devices without
power ON/OFF capability. Use Direct
Code Entry in these cases.
2. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns on.
Release the SETUP button. The red
light will remain on.
NOTE:The red light will either be a
small light at the top of the remote or
the power ON/OFF button.
3. Press and release the device button
on the remote for the type of device
you wish to control, (e.g., TV, DVD,
STR, AUX). The red light will blink
once and remain on.
4. With the remote pointed at the
device, press and release the POWER
button on the remote. The remote
will send 10 dierent codes to the
device. The red light will blink once
for each code and remain on after
sending the 10 codes.
Did the device turn o?
• If YES, go to Step 5.
• If NO, repeat Step 4 to test the
next 10 codes.
5. Manually turn the device back on.
6. With the remote pointed at the
device, press and release the
VOL button. The remote will
re-send the rst code of the 10 codes
from Step 4. The red light will blink
once and remain on.
SETUP
VOL
Auto Code Search
Auto Code Search is a process where you can
search through all the codes stored in the remote
to nd a code for your device. It is recommended
that you read through all the steps below to
familiarize yourself with Auto Code Search before
starting the process.
SRP4229B_07 ENG Manual v2.indd 8SRP4229B_07 ENG Manual v2.indd 8 9/2/21 5:03 PM9/2/21 5:03 PM

9
Programming your remote
Did the device turn o?
• If YES, you have found a code for
the device. Press and release the
same device button you pressed
in Step 3. This will store the code
in the remote. Go to Step 7.
• If NO, continue to press and
release the VOL button until
the device turns o to test the
other 9 codes from Step 4. Be sure
to wait approximately 3 seconds
after each VOL button press to
allow the device time to respond
to the code. When the device
turns o, you have found a code
for your device. Press and release
the same device button pressed in
Step 3. This will store the code in
the remote. Go to Step 7.
NOTE:
• The VOL button can be used to
go backwards through each batch
of 10 codes.
• The red indicator light will ash 2
times after testing the rst or last
code in each batch of 10.
7. Use the remote to turn the device
back on. Test the buttons on the
remote to see if the device responds
as you would expect. If the buttons
do not operate the device, return
to Step 2 and repeat this process to
search for a better code to operate
the device.
8. Repeat this process for each device you wish
to control.
Controlling combo devices
Some combo devices (e.g., TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two dierent
device buttons to control both parts of the combo
device. For example, if you have a TV/DVD combo,
you may need to set up one code under the TV
button to control the TV and a separate code
under the DVD button to control the DVD.
VOL
VOL
SRP4229B_07 ENG Manual v2.indd 9SRP4229B_07 ENG Manual v2.indd 9 9/2/21 5:03 PM9/2/21 5:03 PM

10
Using your remote
Primary Audio Control
The Primary Audio Control feature allows you to
select a single device that the volume buttons
always control. For example, the remote can be
in TV mode while the volume buttons control
the volume on your audio receiver or sound bar
instead of your TV.
Enabling Primary Audio Control
1. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns on.
Release the SETUP button. The red
light will remain on.
2. Press and release the device button
(TV, AUD, etc.) on the remote for the
device you wish to control
the volume.
3. Press and release the MUTE button.
4. Press and release the VOL button.
The red light will blink twice and
turn o.
Disabling Primary Audio Control
1. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns on.
Release the SETUP button. The red
light will remain on.
2. Press and release the device button
(TV, AUD, etc.) programmed to control
the Primary Audio Control feature.
3. Press and release the MUTE button.
4. Press and release the VOL button.
The red light will blink twice and
turn o.
SETUP
SETUP
VOL
VOL
SRP4229B_07 ENG Manual v2.indd 10SRP4229B_07 ENG Manual v2.indd 10 9/2/21 5:03 PM9/2/21 5:03 PM