Philips SRP5018 User manual

SRP5018
Always there to help you
Register your product and get support at
www.philips.com/support
User manual
GrayTurqoise Duotone
Black / PMS300
Question?
Contact
Philips
Question?
Contact
Philips
Question?
Contact
Philips

English
EN 1
Contents
1 Your universal remote 2
Introduction 2
Overview of the universal remote 2
Supported devices 4
2 Get started 5
Insert batteries (not included) 5
3 Use your universal remote control 10
Learning 10
4 Notice 12
Notice of compliance 12
5 Service and support 14
Frequently asked questions 14
Need help? 14
Contents

2 EN
1 Your universal remote
Congratulations on your purchase, and welcome to Philips!To fully
benet from the support that Philips offers, register your product at
www.philips.com/welcome
Introduction
With the universal remote, you can operate up to 8 different devices.
Overview of the universal remote
a : power on or off.
b Device selection buttons
a
b
c
d
e
f
g
h

English
EN 3
c : play
: fast forward
: rewind
: pause
: stop
: record
d Shortcut to the streaming services, pre-programmed as below:
Blue STREAM:Vudu
White STREAM: Netix
Green STREAM: Amazon
e INFO: displays on-screen channel information.
GUIDE: displays the program guide.
OK: conrm your selection.
EXIT: exit from the menu.
MENU: menu on or off.
TREBLE/BASS: select the sound preference.
/ / / : up/down/left/right.
f INPUT: select available source inputs (antenna, cable, etc.).
CH+/CH-: go to the next/previous channel.
: mute
: volume up
: volume down
g PAGE+/PAGE-: go to the next/previous page.
LIVE: displays live TV programs.
LIST: displays a list of recorded programs.
LAST: return to the previous tuned channel.
BACK: go back one menu level.
A/B/C/D: context sensitivity buttons (A - yellow, B - blue, C- red,
D - Green).
h Digit buttons
ENTER: conrm the digit button selection.
(-): selects between one and two-gure channel numbers.
Note
• Shortcuts to streaming services can be re-programmed to other services through
learning (see 'Use your universal remote control' on page 10).

4 EN
Supported devices
Device name Description
TV TV, DTV
BD DVD player/recorder, Blu-ray player
STB(CBL/SAT) Cable box, satellite receiver, IPTV, DVR, HDTV
decoder and TiVo
STR Streaming devices, Apple TV, Roku, Sony,WD TV,
Netgear
SB Sound bar, home theater, audio system
VCR Video cassette player/ recorder
AUX Auxiliary equipment, media center PC, others

English
EN 5
2 Get started
Insert batteries (not included)
Warning
• Check the battery polarity when inserting in the battery compartment. Incorrect
polarity may damage the product.
Caution
• Risk of explosion! Keep batteries away from heat, sunshine or re. Never discard
batteries in re.
• Risk of decreased battery life! Never mix different brands or types of batteries.
Note
• When you replace the batteries, all user settings will be retained in the memory of
the universal remote for 5 minutes.

6 EN
Set up the universal remote
You must rst set up the universal remote before operating your
devices.
Manual registration
1 Switch on your device.
2 Press and hold the device selection button (e.g. TV) for 5 seconds
until the red LED is on.
3 Look up the 5-digit code for your brand in the code list. Codes
are listed by the device type and brand name. The most popular
code is listed rst.

English
EN 7
4 Enter the rst 5-digit code using the digit buttons.
5 If the light is off, a valid code is saved. Otherwise, the light will ash
once, and then remains on for code re-entry.
6 Operate the device with the universal remote. If your device
responds correctly, it means you have entered the right code.
Otherwise, repeat from step 2, and enter the second code on the
list.
Note
• It is possible sometimes that your device only responds to some of the buttons. In
such case, set up with the next code in the code list, and try operating your device
again.
• You may also x the buttons which are not functioning properly by using the learning
feature (see 'Use your universal remote control' on page 10).

8 EN
Auto registration
1 Switch on your device.
2 Press and hold the device selection button (e.g.TV) for 5 seconds
until the red LED is on.
3 Point at your device with the universal remote.Then press and
release to start searching the code for your brand. A different
infrared signal is sent every 2 seconds as the universal remote
searches, indicated by a red ash.